Question about 1996 Mitsubishi Mirage

1 Answer

I need the component diagram for the starter on the car and what is the specs for it . ty

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Mitsubishi Master
  • 14,338 Answers


Posted on Dec 30, 2012

Testimonial: "thank you for the assistance!"

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I need torque specifications with diagram for a 1998 2.2 Isuzu pickup. Can anyone help?

Could you be more specific on what component of your vehicle you need torque specs for ?

Nov 19, 2016 | Isuzu Cars & Trucks

1 Answer

What would make a 1988 ford ranger, motor 2.3. 5 speed run good till it warms up then it dies, & won't start till it cools off?ty

Could be a massive intake air leak being caused by a defective egr valve.
Could be just about anything and it will need similar checks to an engine when it is a cold non-starter with verification of the essentials of spark, fuel, compression and timing.

Lots of components can become temperature temperamental.
Good luck!

Feb 17, 2015 | 1988 Ford Ranger

1 Answer

2007 Duramax Diesel. Change flywheel and starter. Starter Grinding again. What else can be wrong?

My lb7 does this intermittently and I also have replaced the starter many times. After seeing internet postings by hundreds of owners spending many thousands of dollars "to beat a dead horse." It is obvious that gm's design specs of components involved with starter engagement is very poor engineering. This spec allows an accumulation of tolerances of components to be outside of limits. Any engineer worth his salt would have recognized the problem immediately. Since all duramax trucks are prone to this with no proper permanent fix offered by gm, a lawsuit instituted against gm is the only action that will force them to solve the problem.

Apr 24, 2012 | Cars & Trucks

3 Answers


You can test power to the starter, or to starter relay, or to any component with a voltmeter.

Jun 16, 2010 | Cadillac Eldorado Cars & Trucks

1 Answer

Puting vac hoses back on and carberater on a 1984

The engine and emission control system covered by this information operate on a combination of vacuum and electrical signals; they are extremely prone to malfunctions due to improper vacuum connections. If a component does not receive vacuum at the correct time, it cannot function when needed. When working under the hood, pay close attention to the routing and placement of every hose.


Fig. 1: The vacuum hoses are usually numbered for easy identification


Fig. 2: Vacuum hose routing-1984-85 carbureted Prelude


Fig. 47: Emission component schematic-1984-85 carbureted Prelude

Hope this helped; TY for using Fixya (remember comment and rated this).

Apr 01, 2010 | 1984 Honda Prelude

1 Answer

How do i replace a starter for a bmw 325i 2001

What engine size and model do you have?
You can go to and register for full free online repair manual. It has diagrams and step by step directions on how to replace the starter and the torque specs and everything else you could need for this car.

copy and paste in your internet address bar in a new tab:

Nov 11, 2009 | 2001 BMW 325

1 Answer

Need wiring diagram for 1990 ford f-250 4x4 diesel. the glow plug system

If you are looking for a complete wiring harness diagram then faxonautoliterature has the original Ford service manual for your truck which has complete diagrams in it. If you are looking for components to check then Haynes Diesel Engine Repair Manual, part # 10330 has good diagrams of components and terminals pinpointed for testing purposes as well as the specs for those tests and a good diagnostic section. Hope this helps.

Oct 18, 2009 | 1990 Ford F250

2 Answers

Where is the starter on a ford focus se 2001do you have a diagram i recieved no manual with the car......ty

For around $50 you could have your own manual.

I have two(a clean one and the dirty garage copy)HAYNES repair manual for Ford Focus2000 and 2001, couldn't be a better investment next to a code reader.

Aug 04, 2009 | 2001 Ford Focus

1 Answer

I need torque specs for head bolts on 1992 merc benz 230 e

hello,230e with engine 102.982,cylinder head bolt,double hexagonal socket m12, stage 1, 55 newton meter,stage 2 90 degrees stage 3 90 degrees,4 pcs. bolt with m8 tighten to 25 nm.ref. technical data year 1993,ty

Apr 17, 2009 | 1992 Mercedes-Benz E-Class

1 Answer

Front dif torque specs 91 silverado

german specs.......GOODNTIGHT

Dec 16, 2008 | 1991 Chevrolet K1500

Not finding what you are looking for?
1996 Mitsubishi Mirage Logo

Related Topics:

65 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts


Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides