Question about Cars & Trucks

1 Answer

Clutch pedal goes to floor and half works on my b2200 1987 mazda pick-up

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 5,475 Answers

If the clutch is hydraulic operated, you need to bleed the clutch at the slave cylinder, down on the transmission housing. Bleed it just like you bleed brakes of air in the line-open bleeder valve, someone pushes clutch pedal slowly to floor, close valve, and repeat until fluid comes out valve in a steady stream. Make sure the clutch reservoir is full before starting. It uses regular brake fluid.
If not hydraulic, it would be cable operated. Adjust the cable until clutch pedal is right.

Posted on Dec 29, 2012

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad
mcalkins3
  • 123 Answers

SOURCE: Clutch pedal goes to the floor, then after pulling it up there is pressure...

There is either air in the system or a leak in the clutch slave cylinder. Check your fluid make sure it is full and the cap is tight.

Posted on Sep 18, 2008

  • 160 Answers

SOURCE: Clutch Pedal to Floor

slave cylinder needs replaced

Posted on Nov 12, 2008

  • 1 Answer

SOURCE: clutch pedal suddenly goes to

I found that having a wood stick on the clutch pedal down to the floor all night (the other end of the stick held by the seat. oh yeah !!! ) would help to ease shifting for the first hour the next morning, then it would come back stiff and hard to engage in gear.

Posted on Nov 12, 2008

  • 566 Answers

SOURCE: Clutch pedal low near floor, can the clutch be adjusted?

hi the clutch on accent is hydraulic operation so if pedal is very low on disengaging clutch ? you may have a problem with the hydraulics 1st thing to check is fluid level? this is the reservoir that feeds both brakes and clutch but is seperaterated inside if fluid low? top up and bleed the slave cyl however if fluid low indicates a leak ? possibly slave cyl? if no loss of fluid ? then prob may be fault in the master cyl ? check fluid come back with any update please ps if this problem has just occured? check for leaks ?

Posted on Feb 02, 2009

  • 4088 Answers

SOURCE: no pressure clutch pedal goes straight to the floor 1988 holden r

If hydraulic actuated mechanism, loss of fluid, defective master cylinder or slave cylinder at the clutch. Missing pin or other part between slave cylinder and clutch arm. Loose or broken slave cylinder mounting. Missing pin or broken part between pedal and master cylinder. If mechanical linkage, look for broken components or missing pins at moving joints. If you tried to shift into gear with engine running, you may have damaged the transmission gears.

Posted on Aug 11, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1996 Mazda MX6 Clutch pedal has no push back from floor but still shifts


I am not a mazda guy but it sounds like the pressure plate is bad. Have you check the clutch linkage to be sure something did not slip or break. If so I would be looking at the clutch pressure plate.

May 18, 2017 | Mazda Cars & Trucks

1 Answer

My 1995 manual mazda astina horn keeps beeping when i step on the brake? The clutch seems to be sinking into the floor. Are these related and how do i stop my car beeping at innocent people?


Hi, it sounds like you have air getting into your clutch slave cylinder as thats what causes the pedal to sink to the floor when you have air in the system . As for the horn your brake pedal could be touching a bare horn cable that must be some were on the car floor or outside the car . You will have to check inside and out side for a bare wire next to the brake pedal.

Jan 12, 2016 | Mazda Cars & Trucks

1 Answer

Clutch wont return


Does the clutch pedal not return?

Oct 07, 2013 | Cars & Trucks

1 Answer

Cluch pedal lost pressure


The clutch master cylinder reservoir is on the firewall under hood near the brake master cylinder. It has a round black screw on cap as I recall. Use Dot 3 or 4 brake fluid.

Jun 21, 2012 | Mazda 626 Cars & Trucks

1 Answer

I have a 94 dodge stealth and when u press the clutch it just stays on the floor. I have replaced both the clutch master cylinder and slave cylinder but it has fixed the problem yet.


  • Okie dokie,,,they have a really hard bleed success rate.. you can do it by your self ...follow my steps...
  • make sure the pedal is off the floor in the up position
  • use the 10mm unscrew the bleeder screw on the slave cyl about 2 full revoloutions
  • pour fluid in the clutch res start to look down watch it come out the bleeder screw, wait a few seconds and tighten the screw.
  • keep filling the resevoir..it can be messy then put the top cap on the resvoir snug...
  • now you bleed, untighten the bleeder screw a 1/4 turn then go push on your clutch pedal, it if does not go down loosen another 1/4 turn...
  • if the pedal hits the floor>>>>tighten the bleeder screw first then pick-up the peadal...
  • make sure the resevoir is half full ....
  • okay loosen the bleeder screw 1/4 to 1/3 turn again, push the peadal to the floor... let it go all the way down.
  • then go tighten the bleeder screw , and pick up the pedal....
  • keep an eye on your resevoir ...
  • note if you ever remove the clutch cap to fill you must bleed the system..the cap does not hold pressure but it does provide a suction...!!!

May 21, 2010 | 1994 Dodge Stealth

2 Answers

My clutch pedal is stuck to the floor??


It is most likely a hydraulic clutch, and it is most likely leaking at the clutch slave cylinder. Check the clutch master cylinder for fluid, it should be a small master cylinder looking thing with a fill cap next to the brake master cylinder and booster unit. If it is empty fill it with the same dot 3 brake fluid that you use for your brake master cylinder, and make sure that you are pouring the fluid into the clutch master cylinder reservoir and not the rubber seal that should be under the fill cap. After filling the clutch master cylinder up with fluid, then try and pump up the clutch pedal. It might take a while to pump up hydraulic pressure, and you might also have to work the pedal a few times by hand at first.

Also, you might have to bleed the clutch at the slave cylinder if it will not build up enough pressure to release the clutch.

Apr 28, 2010 | 1988 Mazda RX-7

1 Answer

My cluch keeps stiking to the floor in my 1989 mazda mx6


check all mechanical parts of clutch pedal make sure there is no catching or draging in its joint lube if possible also check the spring that pulls the clutch pedal back up make sure not damaged or worn out, A different problem may be in your hydrolic clutch system, such as a bad slave cylinder or your system may just need bleeding, if you have a problem with your hydrolics when the clutch goes to the floor and stays you will not be able to disengage your clutch as well until you pull the clucth back up and pump it a few times.

Apr 03, 2010 | 1989 Mazda MX-6

1 Answer

Will not go into gear


The hydraulic clutch command has failed - either at the pedal pump or at the clutch cylinder. Verify first that the line to the clutch cylinder isn't severed; if it isn't the disconnect it, plug it so it doesn't leak and try to press the pedal -if you can the the pedal pump is faulty, if you can't it's the cylinder. 
Either replace the corresponding seals or replace the entire part.

Apr 01, 2010 | 2002 Mazda Miata

1 Answer

Clutch pedal suddenly goes to the floor, no longer [dis]engaging the clutch


I found that having a wood stick on the clutch pedal down to the floor all night (the other end of the stick held by the seat. oh yeah !!! ) would help to ease shifting for the first hour the next morning, then it would come back stiff and hard to engage in gear.

Aug 07, 2008 | 2007 Mazda B4000

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

238 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

78289 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14405 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...