Question about 2002 Chevrolet Tracker

2 Answers

Replacing an engine in a 2002 chevrolet tracker

I have all the bell housing bolts out and can't get the engine to seperate. do i have to do anything to the torque converter?

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

I know this is not a solution but im about to pull the motor in mine.. you dont have to remove the tranny with the motor do you??

Posted on May 29, 2010

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 3 Answers

There is bolts you have to take out of the flywheel that bolts to the torque converter

Posted on Jan 18, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is crank position sensor on 2002 chrysler town andcountry


the sensor is located in the trans bell housing were the trans bolts to the engine, there is a 3 wire electrical connector. I believe its on the top of the bell housing on the firewall side.

Aug 28, 2014 | 2002 Chrysler Town & Country

1 Answer

Replace Slave Cylinder 2002 VW transporter


The heading is replace slave cylinder of 2002 vw transporter. Why would you be removing the tranny to do this job as the slave cylinder is on the outside of the bell housing. IT is normal to remove the bell housing with the tranny as they are normally one unit as the bolts are inside and cannot be reached until the tranny is on the ground. Having said that, if there are 4 bolts in a flange outside the tranny proper and the bell housing is tightened with these bolts then you can remove the tranny separate to the bell housing.

Nov 25, 2013 | Cars & Trucks

2 Answers

2002 dodge intrepid bell housing bolts


Buy one bolt from dealer --then the rest at a better
price else where

You know the width of the trans flange & the depth
of the engine threaded hole, so you need to be a little
short, so not to bottom out

Learning how to measure metric threads is something
you got to learn

You need a chart & know how to do the math as well, to
convert decimal to metric

Working on a car today is not like the 1960's

You need a micrometer & a vernier caliper

I use them almost every week,helps of coarse
if you stared out a machinist I guess

Oct 20, 2012 | 2002 Dodge Intrepid

1 Answer

Where is the thermostat on a 2002 chevy tracker


follow the upper radiator hose from the radiator to engine,you should see a dome like housing,it is under it!

Oct 12, 2012 | 2002 Chevrolet Tracker

1 Answer

Where is the coolant thermostat located on the 2002 Tracker with 2.5L V6 engine?


follow your upper radiator hose till it meets the motor.the metal piece that this clamps to is the thermostat housing,under this housing is the thermostat

Jan 24, 2011 | 2002 Chevrolet Tracker

2 Answers

I pulled all the bellhousing bolts..motor mount bolts...and can't seperate the 4 speed granny transmission from the engine block...what's the problem..everything is lose but won't seperate..


The input shaft (on the front of the trans) is inserted into the clutch plate, so the trans has to move straight backward (or the engine has to move straight forward) about two or three inches to separate the two, before either one can move up or down.

Make sure that you can get them to rotate slightly with respect to each other, to make sure that there is not one more bolt somewhere that is still holding them together.

If you are pulling the engine, make sure that you have already removed the radiator, otherwise when you pull the engine forward, it could go too far and smash the radiator.

Oct 10, 2010 | Dodge D150 Cars & Trucks

2 Answers

Where is the crankshaft sensor located on the 1999 Chevrolet Tracker?


I have a 99 chevy tracker and mine is behind the starter.

Sep 10, 2010 | 1999 Chevrolet Tracker

1 Answer

Thermostat


  1. Disconnect the negative battery cable.
  2. Drain the cooling system.
  3. Remove the three bolts and position the A/C compressor aside.
  4. Remove the radiator hose clamp from the thermostat housing.
  5. Remove the radiator hose from the thermostat housing.
  6. Remove the three bolts and the thermostat housing.
  7. Remove the thermostat and the O-ring from the thermostat housing.
  8. Clean any corrosion or debris from the thermostat housing.
  9. Clean the mating surfaces.
  10. Inspect the thermostat.

To install:

WARNING Position the air bleed valve on the thermostat toward the top of the engine.
  1. Install the thermostat in the described position to the cylinder head.
  2. Install a new thermostat O-ring.
  3. Install the thermostat housing.
  4. Secure the thermostat housing with three bolts and tighten to 12 ft. lbs. (16 Nm).
  5. Install the A/C compressor and secure with three bolts. Tighten the A/C compressor bolts to 17 ft. lbs. (23 Nm).
  6. Install the radiator hose and clamp to the thermostat housing.
  7. Fill the radiator with approved coolant.
  8. Connect the negative battery cable.
  9. Start the engine.
  10. Allow the coolant to attain operating temperature (both hoses feel warm and the coolant is flowing through the radiator).
  11. Check for leaks in the cooling system.
  12. Shut off the engine.
  13. Install the radiator cap.



Short answer is that it is located in the housing that the TOP radiator hose is attached to at the engine block.


Thanks for using FixYa - a FixYa rating is appreciated for answering your FREE question.

Apr 05, 2009 | 2002 Chevrolet Tracker

Not finding what you are looking for?
2002 Chevrolet Tracker Logo

Related Topics:

235 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

64286 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...