Question about 2002 Toyota Camry

Open Question

2004 Lexus GX470 can't set auto door unlocking function

The auto door locking function is working but when I try to program the doors to auto unlock when the car is in park, it will not work. I followed the manual instructions which say to 1. put ignition in the "on" position 2. within 10 seconds push and hold the power door locking switch to "unlock" position for 5 seconds

locks should unlock and lock if this is done properly. I tried multiple times and have no success. Any ideas?

Thanks,
Garrett

Posted by on

6 Suggested Answers

emissionwiz
  • 60792 Answers

SOURCE: Single power door lock does not work

If it doesn't work from master switch then the door lock motor actuator will need to be replaced, this requires pulling the door panel.

Posted on Sep 20, 2008

bad_dog1
  • 104 Answers

SOURCE: drivers door power lock wont work.

Either the wring going to that motor or the motor itself is bad.

Posted on Mar 09, 2009

  • 5 Answers

SOURCE: Need to know how to adjust the door auto lock function.

Not an easy fix! The door lock function was designed to lock doors only. you can however, disable this lock feature by simply cutting the light blue automatic door lock signal wire on the 6-wire harness plug connector located on the chime module (In component center).

Posted on Mar 15, 2009

icarus_26
  • 4 Answers

SOURCE: 1998 Toyota Avalon with power door locks, front

Check this site out
you need the passenger side door lock assembly kit.
There is one posted for sale in the US on this site. just scroll down for the following information and link
Used 1998 Toyota Avalon passenger door lock assembly 1998 Toyota Avalon
passenger door lock assembly
this is the part that surrounds the lock driver side. Car color is green cary, North Carolina 27513
The solenoid or actuator arm for the door lock assembly is probably not working to full spec.

Hope this helps.

Posted on Apr 22, 2009

  • 1 Answer

SOURCE: Drive Door lock only works manually

It is not that hard to fix. Actuater is sold as part of the assembly. You can't just replace it by itself. Order the part online for a lot less than dealer. I learned that when the passenger side did the same thing a couple months later and I saved $150 on line. Remove the inside door panel. Remove lock assembly from door. Remove door handle.

Posted on Apr 24, 2009

  • 574 Answers

SOURCE: 1998 Toyota 4runner driver side power door lock problem.

probably gonna have to take the door panel off. You say it wont unlock or lock with the key? if thats the case its probably broke inside the door.

Posted on Aug 23, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Doors dont lock with secrity fob


The receiver for the fobs is located in the rear hatch, and it needs to be reprogrammed to the fobs. Try the following procedure;

1. Close all the vehicle doors.
2. Insert the ignition key into the ignition lock cylinder.
3. Press and hold the door unlock switch.
4. While holding the door lock switch in the unlock position, cycle
the ignition ON, OFF, ON, OFF.
5. Release the door unlock switch. The doors will lock and unlock to
confirm the program mode.
6. Press and hold the LOCK button and the UNLOCK button
simultaneously on one transmitter. After a delay of approximately 15
seconds, the doors will lock and unlock to confirm the programming of
that transmitter.
7. Repeat the previous step to program up to four transmitters.
8. Turn the ignition switch to the RUN position in order to exit the
keyless entry transmitter mode.
9. Operate the transmitter functions in order to verify correct
system operation.

Sep 05, 2012 | 2004 Chevrolet TrailBlazer

1 Answer

Lexus ES300 door auto lock and unlock does not work


i have a 1997 lexus es300 having problems with unlocking the doors and the trunk with the keyless remote the doors will lock with the keyless remote

Apr 09, 2012 | 2000 Lexus ES 300

1 Answer

2004 lexus gx470 rear door won't open...I can hear the lock click when I press the alarm key but the door will not open


Try opening door manually from inside, once open and make sure child safety switch (near lock mechanism isn't between on/off) They're known for jamming between settings. If that doesn't work then you'll have to remove inside door panel and access latch mechanism.

Mar 02, 2011 | 2004 Lexus GX 470

1 Answer

Doors won't lock with remote on my 2002 Lexus GS 300.


are you sure the battery is good in the remote? if so try putting the key in the driver door lock and locking and unlocking the doors three times in a row. if this dosent work i suggest taking it to an experienced lexus shop.

Oct 06, 2009 | 2002 Lexus Gs 300

1 Answer

Un work of the doors auto control lexus


1. sitting in driver seat, with driver's door OPEN, press lock/unlock button ON THE DRIVERS DOOR to lock all doors, then manually unlock driver door only.
2. Insert YOUR key in ignition, DO NOT TURN, then remove key.
3. Using the same lock/unlock button ON THE DRIVERS DOOR, slowly press lock-unlock in 5 cycles
4. Shut door.
5. Open door.
6. Using the same lock/unlock button ON THE DRIVERS DOOR, again slowly press lock-unlock in 5 cycles
7. With the door open insert your key into the ignition, turn to 'on' position (DON'T START), wait 5 seconds. Turn off and remove key.
8. Locks should cycle once (Car will lock and then unlock once by herself). If they don't cycle or they cycle more than once, do steps 1-7 over.
9. Now using the remote, push lock button, hold for one second, then release the button. The locks should cycle once. If not, start over and go slower.
10. Close the door.
11. Open the door.
12. Press the lock button on the remote. The locks should do a lock-unlock cycle.
13. Close the door
14. Press the lock button on the remote, the doors should lock.
15. Press unlock button and the doors should unlock.

Long beep to follow if successful.

Jun 16, 2009 | 1996 Lexus LS 400

1 Answer

Need the steps to programme the remote


Remote Programming Instructions

1. Driver's door OPEN and unlocked, all other doors closed and locked.

2. Insert YOUR key in ignition, DO NOT TURN, remove key.

3. Using the MANUAL lock/unlock button ON THE DRIVERS DOOR, slowly press lock and unlock 5 times (count the lock 5 times and unlock 5 times).

4. Shut door.

5. Open door.

6. Using the lock/unlock button ON THE DRIVERS DOOR, slowly press lock and unlock 5 times (count the lock 5 times and unlock 5 times).

7. With the door open insert your key into the ignition, turn to on position (DON'T START), wait 5 seconds. Turn off and remove key.

8. Locks should cycle once (Car will lock and then unlock once). If they don't cycle or they cycle more than once, do steps 1-7 over.

9. Now using the remote, push lock button, hold for one second,
release. The locks should cycle once. If not, start over and go slower.

10. Close the door. Open the door. Press the lock button on the remote. The locks should cycle. Close the door. Press the lock button on the remote, the doors should lock. Press again and the doors should unlock.

Jun 02, 2009 | 1995 Lexus LS 400

3 Answers

The Lexus car remote key control model ES300


try this:

1. Start with key out of ignition, drivers door is open all others closed and
drivers door is unlocked.

2. Insert key into the ignition (DO NOT Turn) and Pull key out.
3. Perform these steps within 40 seconds.
A. Using the power lock switch on the drivers door, perform 5 lock/unlock cycles
starting with lock. Use an even pace and try to go about one cycle per second.
(1Cycle = 1 lock and 1 unlock).
B. Close, then open drivers door.

4. Perform these steps within 40 seconds.
A. Using the power lock switch on the drivers door, perform 5 lock/unlock cycles
starting with lock. Use an even pace and try to go about one cycle per second.
(1Cycle = 1 lock and 1 unlock).
B. Insert the key in the ignition cylinder.
C. Turn the ignition to ON (Do NOT Start) then back to OFF.
D. Remove the key from the ignition.

5. Press any button on remote for a minimum of 1 second.
System should now lock and unlock doors once.

6. Close and open drivers door.

7. Press any button on remote for a minimum of 1 second. System should now lock and
unlock doors. Once to confirm programming, twice to indicate programming failed.

8. Repeat steps 5, 6 and 7 for additional remotes.

Mar 23, 2009 | 1997 Lexus ES 300

1 Answer

Power locks not working right


Hey, this might work.....get in truck, close doors, put key in ignition in lock position.....hold down the door lock button on driver side door control and wait for the lock control to be displayed on the information screen(odometer read-out).....it should say like lock 1, lock 2, lock 3, lock 4.....or something, I always reset mine to LOCK 1, to do this hold the odometer reset button on dash for a sec or two til it changes settings, then release, repeat till you get to LOCK 1, then quickly press and release odometer reset button to exit program, this is the function to lock doors over 15 mph and when out of park and to unlock doors when returned to park......yours' might be set to another function number....try it out, let me know if this helps.........good luck!

Nov 10, 2008 | 2004 Chevrolet Colorado

Not finding what you are looking for?
2002 Toyota Camry Logo

Related Topics:

368 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

60769 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...