Question about 2000 Chrysler Town & Country

1 Answer

I have a 2000 Town and Country and the brake lights aren't working. I know about the brake light switch, but I want to check the fuse first. Problem is, I can't find it. There are no fuses that I can find related to the brake lights either under the hood or in the interior fuse panel.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 979 Answers

Look under the hood where the fuses are. You should also find relay switches in the same compartment. They usually are silver. This could be your problem. Next, try checking the fuse panel cover and see if the diagram says where they are. There may be a fuse panel on the passenger side of the car. There is on efor the brake lights somewhere. If you don't locate it, check your owner's manual or call the dealer.

Posted on Jan 17, 2009

  • Bill Dickerson
    Bill Dickerson Jan 17, 2009

    Look at the comments I put above.

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2000 Chrysler Town & Country Tail lights and dash lights won't work


If the brake lights and turn signal lights work, then there may be a bad fuse. Check the fuse box.

Mar 21, 2013 | Chrysler Town and Country Cars & Trucks

1 Answer

1998 chrysler town &country brake lights dont work but the 3rd one does


do your dash lights go out too? .. corroded wires (you can do an insulation breakdown test), or its grounding out in the console, but that would most likely blow the fuse. check to make sure u r looking at the right fuse too, wires can be connected to other random components, for example you may find your horn doesnt work either. and being as you have 3 brake lights, it may be possible they are on 2 diff fuses

hope this helps some!

Feb 23, 2012 | 1998 Chrysler Town & Country

1 Answer

Rear brake lights not working 2005 chrysler town and country


check fuses but first refer to owners manual to see proper disconnection of battery neg. first -- obtain acess to brake lights and use dvom ''digital volt ohm meter '' to test continuity to brake lights

Dec 15, 2011 | 2005 Chrysler Town & Country

1 Answer

Brake lights on 1999 Chrysler town and country van does not work, any suggestions


Check fuses, wires and bulbs, finally check brake switch, generally is located backside brake peddal.

May 11, 2011 | 1999 Chrysler Town & Country

1 Answer

My brake lights wont work at all light bulbs has been replaced and fuses been checked its a 1996 chrysler town & country


Brake light switch can be checked with a test light. Since the 3rd brake light is not working That's probably the problem.

Feb 15, 2011 | 1996 Chrysler Town & Country

1 Answer

My stop lights wont work. the lights come on but when i press the brake nothing happens they wont work. i checked the bulbs and fuses they are all working.


Did you check the brake Switch ? Maybe it could be the problem Also what do you mean by The lights comes on ? Good luck

Dec 17, 2010 | 1996 Chrysler Town & Country

1 Answer

No brake lights, new bulbs. where is fuse box in 2001 town & country


If both of your brake lights are out including the third light above the rear door you should check 1: brake switch located behind brake pedal. 2: relays under hood although not a likely problem. 3: trailer wiring if there is any. Most likely it will be the first though as it controls all brake lights.

Sep 08, 2010 | 2001 Chrysler Town & Country

2 Answers

Brake lights not working on my chevy malibu


Check fuse/relay and then check the brake switch under the dash close to the brake pedal. It tells the brake lights to come on when you apply the brakes.

May 01, 2009 | 2000 Chevrolet Malibu

1 Answer

Brake lights not working


BRAKE LIGHT SWITCH LOCATED ABOVE THE BRAKE PEDAL

Jan 13, 2009 | 2000 Chrysler Town & Country

1 Answer

My 2001 Town & Country Break Light is not working.


David, is it one brake light, or both not working? If it's both, check the brake light switch (mounted high on the brake pedal). Let me know what u find.

Nov 28, 2008 | 2001 Chrysler Town & Country

Not finding what you are looking for?
2000 Chrysler Town & Country Logo

371 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

60769 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

chargerhp
chargerhp

Level 3 Expert

813 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...