Question about 2001 Chevrolet Cavalier

2 Answers

My power steering pump just went out on my z24 - fluid to the top of the res. - Looking to replace the pump and pressure hose; is this a difficult process?

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Mine needs to be replaced also, and i sure hope these "so called mechanics" give you a real answer, and not one that says remove belts, pulley so on, because on mine 2001 cav z24 2.4 there is NO belts attached to it, they are on completely opposite sides of the engine.

Posted on Aug 03, 2012

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,990 Answers

#1 it is Over Full, You should have just enough in it too read on the Check Level Cap. Over Filling will Wear out the Seals. #2 It is NOT an Easy Repair and is Time Consuming and Frustrating, If you attempt this Repair, BE PATIENT, You will get it.

Posted on Jan 17, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How involved is it to replace a power steering pump on a 2007 Explorer 4.0?


Power Steering Pump - 4.0L Special Tool(s) Installer Set, Teflon® Seal
211-D027 (D90P-3517-A) or equivalent Material Item Specification MERCON® V Automatic Transmission Fluid
XT-5-QM (or XT-5-QMC) (US); CXT-5-LM12 (Canada) MERCON® V
Item Part Number Description 1 388898 Teflon® seal 2 - Pressure line-to-pump fitting (part of 3A719) 3 W700839 Power steering pump bolts (3 required) 4 3A674 Power steering pump 5 W503924 Pressure line bracket-to-engine bolt 6 3691 Power steering pump supply hose 7 W503924 Power steering pump supply hose bracket bolt
Removal
NOTICE: While repairing the power steering system, care should be taken to prevent the entry of foreign material or failure of the power steering components may result.

  1. Using a suitable suction device, remove the power steering fluid from the reservoir.
  1. With the vehicle in NEUTRAL, position it on a hoist. For additional information, refer to Section 100-02.
  1. Remove the power steering pump pulley. For additional information, refer to Power Steering Pump Pulley - 4.0Lin this section.
  1. Remove the pressure line bracket-to-engine bolt.
  1. Remove the power steering pump supply hose bracket bolt.
  1. Release the power steering pump supply hose clamp and disconnect the hose.
  1. Disconnect the pressure line-to-pump fitting.
    • Remove and discard the Teflon® seal.
  1. Remove the 3 bolts and the power steering pump.
Installation
  1. NOTE:A new Teflon® seal must be installed.Using the Teflon® Seal Installer Set, install a new Teflon® seal to the pressure line fitting.
  1. Position the power steering pump and install the 3 bolts.
    • Tighten to 25 Nm (18 lb-ft).
  1. Connect the pressure line-to-pump fitting.
    • Tighten to 75 Nm (55 lb-ft).
  1. Connect the power steering pump supply hose.
  1. Install the power steering pump supply hose bracket bolt.
    • Tighten to 11 Nm (97 lb-in).
  1. Install the pressure line bracket-to-engine bolt.
    • Tighten to 11 Nm (97 lb-in).
  1. Install the power steering pump pulley. For additional information, refer to Power Steering Pump Pulley - 4.0Lin this section.
  1. Fill the power steering system. For additional information, refer to Section 211-00.

Apr 13, 2016 | Ford Cars & Trucks

3 Answers

Power steering fluid leaking. change hose? change pump? Re clamp?


If the hose itself is leaking (not the connection/end) , replace the hose. If the hose is more than 5 years old, I'd probably just replace it. If it's the low pressure hose (return) and it's leaking at the junction, you can probably replace the clamp. If it's the high pressure hose (with the machine-formed hose ends) then replace the hose - a clamp is unlikely to withstand the pressure and you don't want to take the chance of it blowing off when you're turning.

Oct 17, 2015 | Cars & Trucks

1 Answer

Power steering hose


Your steering pump will suffer badly.

Aug 29, 2012 | 1988 Chevrolet Cavalier Z24

2 Answers

Replace power steering pump on 06 chevy uplander


I just finished replacing mine.

It is much easier if you do these steps:

1. Remove the serpentine belt.
2. Remove the nuts holding the main fuse box over the battery.
3. Remove the reinforcing bar over the battery.
4. Remove the battery.
5. Remove the windsheild washer tank.
6. Now you have access to remove the pump pulley. Without removing the stuff, it may be possible, but it will be extremely difficult.
7. Remove the pump pulley.
8. Loosen the high pressure hose fitting.
9. Remove the return line clamp.
10. Remove the power steering pump mounting bolts.
11. Remove the high pressure hose fitting.
12. Remove the power steering pump while sliding off the low pressure hose.
13. Remove the clips holding the reservoir on the pump.
14. Remove the reservoir.
15. Install new o-ring on the reservoir.
16. Install reservoir on new pump.
17. Install clips to hold reservoir on pump.
18. Install new o-ring on high pressure fitting.
19. Place new pump in position while sliding on low pressure hose.
20. Loosely attache high pressure fitting.
21. Tighten pump to mounts.
22. Tighten high pressure fitting.
23. Install clamp on low pressure hose.
24. Install power steering pulley.
25. Install washer reservoir.
26. Install battery.
27. Install reinforcing cross member.
28. Install fuse panel.
29. Install serpentine belt.
30. Bleed the power steering system.

Jul 08, 2012 | 2006 Chevrolet Uplander

1 Answer

On a 99 Olds Alero, in the return lines of the power steering hoses, which place does the high pressure hose attach to?


RETURN TURN LINE GOES TO THE LEFT OF RACK PINION AND HIGH PRESSURE HOSE GOES TO THE RIGHT OF RACK PINION.LOOKING AT POWER STEERING PUMP HIGH PRESSURE HOSE THICK HOSE SCREWS INTO POWER STEERING PUMP.WHILE LOW PRESSURE HOSE HAS A HOSE WITH A CLAMP THE LOW PRESSURE HOSE HOOKS TO TOP OF POWER STEERING PUMP.LOW PRESSURE DONT SCREW INTO POWER STEERING PUMP IT IS HELD IN PLACE BY A HOSE SMALL CLAMP.

Jun 24, 2011 | 1999 Oldsmobile Alero

1 Answer

Is it very difficult to change the power steering pump in a 2004 kia sedona?


  1. Remove the Power Steering belt.
  2. Disconnect the power steering hoses from the power steering pump. Take caution as there may be some pressure.
  3. Remove the bolts holding the Power Steering pump to the pump mount.
  4. Install the new Power Steering pump.
  5. Reconnect the power steering hoses.
  6. Reconnect the Power Steering belt.
  7. Top off with fluid.
  8. Start up the vehicle.
  9. Turn the wheel to the left.
  10. Top off with fluid.
  11. Turn the wheel all the way to the right.
  12. Top off with fluid.
  13. Repeat the last 4 steps until the fluid level doesn't change much, and is topped off.

Feb 18, 2011 | 2006 Kia Sedona

1 Answer

Show me how to replace power steering pressure hose on 1995 GMC Yukon


It's very easy, undo screw one end from back of power steering pump, no need to remove pump, and unscrew other end of hose from steering gear box, replace hose and top off with power steering fluid, when you undo power steering hose have a pan to catch the power steering fluid that will drip out.

Aug 17, 2010 | GMC Yukon Cars & Trucks

3 Answers

I have a 97 taurs with a steering problem. It makes a humming noise that gets louder the faster I go. It pulls to the right, an when I go around a left corner it feels like it just doesn't want to turn...


check to see if you have power steering fluid. if your low fill it up. (most cases thats all it is) check around for any leaks or parts to the power steering unit for and damage (hoses, pump, rer, rack and pinion, any seals or such. you might have a leak somewhere. when your looking for leaks fill the res up with power steering fluid. turn the car on. and have someone turn the wheel so get the fluid to build up pressure in the system.

Oct 12, 2009 | 1997 Ford Taurus

1 Answer

How to r&r powersteering pump 1998 mercury grand marquis


Hopfully this will be ALL you need Besides Pulley REMOVAL TOOL It can be Rented @ AutoZONE

REMOVAL
  1. Remove drive belt.
  2. Raise vehicle on hoist. WARNING: TURN AIR SUSPENSION SWITCH (LOCATED IN LUGGAGE COMPARTMENT) OFF TO PREVENT VEHICLE DAMAGE OR PERSONAL INJURY.
  3. Remove power steering pressure hose bracket.
  4. Disconnect electrical connector at power steering control valve actuator.
    1. Install Steering Pump Pulley Remover T69L-10300-B on the pulley hub. CAUTION: Do not apply in-and-out pressure on the power steering pump shaft. Pressure will damage the internal thrust areas.
    2. Hold the small hex-head and rotate the tool nut counterclockwise to remove the power steering pump pulley.
    3. Disconnect power steering pressure hose at power steering pump and drain fluid into a container.
    4. Disconnect power steering return hose at power steering pump and drain fluid into a container.
    5. Remove four retaining bolts and power steering pump and power steering pump pulley assembly.
    6. Remove power steering pressure switch from pump.
    INSTALLATION
    1. Position the power steering pump on the mounting bosses of engine block and install the bolts at the side of the power steering pump. Tighten to 20-30 Nm (15-22 ft. lbs.).
    2. Connect the power steering reservoir pump hose to the power steering pump and reposition the hose clamp to power steering pump inlet fitting.
    3. Replace power steering pressure hose O-ring.
    4. Install the power steering pressure hose to the power steering pump fitting. Tighten the tube nut with a tube nut wrench rather than with an open-end wrench. Tighten to 34-46 Nm (26-33 ft. lbs.). NOTE: Swivel or end play of the power steering pressure hose end is normal and does not indicate a loose fitting.
    5. Place the power steering pump pulley on the power steering pump shaft and install Power Steering Pump Pulley Replacer T91P-3A733-A. The small diameter threads on the tool should be engaged in the power steering pump shaft. CAUTION: Do not apply in and out pressure on the shaft. Pressure will damage the internal rotating group.
    6. Hold the small hex-head and rotate the tool nut clockwise to install the power steering pump pulley on the shaft. CAUTION: Do not apply in and out pressure on the shaft. Pressure will damage the internal rotating group. NOTE: The power steering pump pulley face must be flush within 0.25 mm (0.010 inch) of the end of the pump shaft.
    7. Remove the Power Steering Pump Pulley Replacer T91P-3A733-A.
    8. Remove the shipping tube nut from power steering pump housing prior to installation.
    9. Connect electrical connector to power steering control valve actuator.
    1. Install power steering pressure hose bracket.
    1. Lower the vehicle.
    2. If equipped, turn the air suspension ON.
    3. Install drive belt on the power steering pump pulley.
    4. Fill the power steering pump reservoir with Power Steering Fluid Motorcraft MERCON(r) ATF.

Oct 04, 2009 | 1998 Mercury Grand Marquis

1 Answer

How to replace Power Steering Pump 95 Town Car


  1. Disconnect power steering pump return line and allow power steering pump fluid to drain into a suitable container.
  2. Disconnect power steering pump pressure hose from pump fitting.
  3. Disconnect drive belt from power steering pump pulley, remove pulley, then remove pump.
  4. Reverse procedure to install. Torque pump to mounting bracket bolts to 30-45 ft lb.

Jan 23, 2009 | 1995 Lincoln Town Car

Not finding what you are looking for?
2001 Chevrolet Cavalier Logo

134 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...