Question about 2000 Chevrolet Venture

1 Answer

Front wipers don't park right

After a winter storm, my wipers still work, but stop in up position rather than under hood.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Expert
  • 45 Answers

Put them into the off position, then unscrew them there will be on a cog place them were they should bethen screw them back, just check the cog first make sure there are no teath are missing on it.

Posted on Jan 17, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2007 Pontiac g6 wipers stay in upright position


Hey Derek , here is how the wipers park position is suppose to work !
Windshield wiper motor park operation is controlled by the body control module (BCM) using an input from the park switch within the wiper motor assembly. The BCM monitors the windshield wiper motor park switch circuit to determine if the windshield wiper blades are at the bottom of the glass. The circuit will be pulled to ground by the wiper motor park switch while the windshield wiper motor is operating. When the wiper switch is turned to the OFF position while the wiper motor is somewhere in mid-cycle, the BCM will continue to operate the motor until the wipers reach the park position. If the ignition is turned OFF while the wipers are in mid-cycle, the wipers will stop immediately where they are. The BCM will park the wipers the next time the ignition is turned ON.
The wipers will not park when they are commanded ON and OFF with a scan tool. The BCM will park the wipers the next time the wiper switch is turned ON and OFF.
The BCM provides stall protection for the wiper motor by monitoring the park switch. If the park switch does not transition for 3 seconds while the wipers are operating, the BCM will assume that the wiper motor is stalled, and will de-energize the wiper relay until the wiper switch is cycled OFF and ON again.
Check for a voltage signal on the yellow wire at the wiper motor assembly , this is signal to the BCM ! If there is no signal you need to replace the windshield wiper motor assembly ? If there is a signal need to have Tech 2 scan tool hooked up to see if The BCM is the problem ! Relay #39 an #40 are the high an low wiper relays in the under hood fuse block ! Do you have a volt meter ,do you know how to do electrical testing ?

Sep 21, 2015 | Pontiac Cars & Trucks

1 Answer

Windshield wipers stop working


At the base of the wiper arm there is a plastic cap,pop this off ,underneath there is a nut that holds the arm in place ,if it gets loose the post will turn inside the blade.Just turn the wipers off and tighten the nuts with the blade in the parked position.

Jan 23, 2012 | 2003 Chevrolet Impala

1 Answer

The windshield wipers to my Ford focus stopped working today. They worked for a little while & then stopped in the up position. You can hear the motor working but they don't move. You can move them...


Your wiper linkage has come off the wiper motor. To reconnect the linkage, first remove the wiped arms, the remove the wiped cowl. The wiper cowl bolts are located under the hood and screws through the spaces in the cowl. Reconnect linkage, reinstall cowl, reinstall wiped arms.

Jul 05, 2011 | 2006 Ford Focus

1 Answer

My windshield wipers stopped working right after winter storm. the driverside one works only if i pull it halfway up the windshield what do i do to fix this


there are plastic bushings on the end of the wiper arms ...called wiper transmission...most places will tell you they dont sell them...keep looking cause they do.....they only snap in and then press on the arms

Mar 06, 2010 | 1998 Ford Expedition

2 Answers

Wipers do not work in intermittent position. They do work in low and high speeds but do not automatically return to the park position. They stop wherever you turn the switch off.


i belive that your wiper switch has gone out on the intermittent side. this is a very common problem.
I hope this helps you
Thanks
Please leave rating

Apr 21, 2009 | 2000 Isuzu Amigo

1 Answer

ES350 Winshield wipers will not tuck under the hood


Yes... u can just pull them back down into position. the wipers on ur car has to positions winter (up) and Summer (down). just push them down and they will snap into the down position

Apr 05, 2009 | 2007 Lexus ES 350

1 Answer

I changed the wiper motor out.  They worked without the blades on, but after installing the blades they tried to move down toward the hood.  I think the motor still works but it seems the shafts are just...


you may of fitted the blades when the wiper motor wasnt in park

ok remove wiper arms turn ignition on turn on wipers then turn of by wiper swicth not key motor will stop in park position fit wiper arms in positon try and your done

Jan 08, 2009 | 1997 Acura TL Series

Not finding what you are looking for?
2000 Chevrolet Venture Logo

Related Topics:

146 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

60792 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...