Question about 2000 Ford Expedition

2 Answers

How to reset my remote starter system

My ford explorer don't start ,and the controlers don't work

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Master
  • 416 Answers

1. Unplug all connectors from the module.
. Press and hold the programming button while inserting the 4-PIN
standard connector.
3. The LED will begin to fl ash red. Immediately release the programming button.
The LED will turn on solid for seconds to confi rm module reset.
4. Plug remaining connectors and return to: STEP 1: SELECT INSTALLATION MODE

Good Luck

Posted on Jan 17, 2009

×

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 221 Answers

Hese instructions may also be valid for other years and models.This procedure clears the transmitter codes and creates new ones, so you must program all remotes at the same time, even if one or more is already working.Enter the car, and close all doors.Each of the following steps must be completed within five seconds of completing the previous step. If you take longer or make a mistake, start the entire procedure over again.Insert the key into the ignition, and hold one remote in your left hand. Whenever the instructions say to press the LOCK button, you should press the lock button on the remote for about a second and then release it.Perform each of the following three steps in order, then repeat all three steps two more times, for a total of three times each:1. Turn the ignition switch to the ON position, marked II
2. Press the LOCK button. 
3. Turn the ignition switch to the Off position, marked I.Do this three times!Next, turn the ignition switch to the ON position (II) for a fourth time.Press the LOCK button again. The door locks should now make a cycling sound, indicating that the system has entered Programming Mode.Press the LOCK button one more time to program this remote. If you have other remotes to program, press the LOCKbutton on each one in turn. The door locks should make the cycling sound after you press LOCK on each remote. You may program up to three remotes, and they must all be programmed within ten seconds of each other.Turn the ignition off and remove the key. The remotes are now programmed and may be tested.If you've got a trunk/hatch release, hold the button for this function for a few seconds. 

Posted on Jan 17, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need a wiring digram for a 2004 Ford Explorer starting system


Sorry but I can't help with a diagram.

I think your car could be a CANbus system where there is no direct connection between the starter switch and the starter motor. Starting is likely to be controlled by a relay which is energised by an ECU if the immobiliser has been disarmed, the starter switch only serving to send a signal to a nearby computer for starting to take place.

If this is your system it is possible to check the switch, relay, starter in the traditional manner but glitches in the system will need specialist diagnostic equipment to locate.

Apologies if I have guessed wrongly...

Aug 10, 2016 | 2004 Ford Explorer

1 Answer

How do i reset a 99 explorer factory alarm


you need the remote control to do it if you disconnected the battery and then reconnected it when the alarm goes off you have to press the disarm button otherwise the alarm goes into theft mode and will not start buy the remote control if you need it now and you can program it into the system once in and the pats system has it stored you will then be able to start your car again good luck

Feb 17, 2015 | 1999 Ford Explorer

2 Answers

Troubleshooting starter system


Dirty battery cables or faulty starter. Do the lights stay on bright while starting?

Mar 29, 2014 | 2002 Ford Explorer Sport Trac

2 Answers

2004 ford explorer will not turn over with key but remote starter switch makes it turn over


Its a good possibility that the Anti-theft is interferring with the circuit. If you have an extra ignition key, use that in case the password chip in your regular FOB has detriorated.

There is a brake sensor which is on the upper brake pedal. It interlocks with the starter to prevent starting without having your foot on the brake pedal. Check your brake lights for operation. If the brake lights stay dark with your foot on the pedal, the switch is broke or knocked out of position. A common problem.

Next, there are small wires for the starter solenoid. You can use a test light on one removed wire and ground the test light to the vehicle, the other end in the small wire. Turn the keyswitch to start, with brake pedal pressed and see if it lights up. If it does light up, the starter solenoid may be bad.

Battery level. Ford Anti-theft and some say Battery-saver, can cause both starting and charging problems. A fully charged battery can be at 13.2V- 13.6V. When Ford systems detect low voltage it can activate the Anti-theft, battery-saver, and even disconnect the charging system to allow the battery to completely drain. In some cases the Anti-theft drops starter voltage to around 7V so the starter will not spin. Have the battery tested.

I know of 2004 trucks that were jump started and showed charging, then after 5-10 minutes they lost the charging system. Some people lost the charging system at 70MPH and drove until they stalled. All because of the automatic features built into the trucks. A new battery fixed the problem. Your problem could stem from this.

May 28, 2012 | 2004 Ford Explorer

2 Answers

My 2003 Ford explorer has a Ford remote starter and it


no take it 2 dealer ask a mechanic if theres a trick or does it need to be re proged

Jan 13, 2010 | 2003 Ford Explorer

2 Answers

Remote Starter won't work!!!


start by disconnecting battery for 15 minutes. if that doesn't work find the box under your dash by the fuse box that has the spare ignition key in it. make sure the alarm system is getting a good signal from the spare keys computer ship which is inside of it. thats the only way they work.other than that look up programming sequence online. best of luck.

Dec 11, 2009 | 2002 Ford Explorer

1 Answer

2004 ford explorer will not start after battery been replace and remote is working


You should get the started tested out of the car. If that's good check the starter relay. If thats not it then you can check the voltage drop and the resistance on the battery cable from the battery down to the starter( the positive cable).

Jul 28, 2009 | 1998 Ford Explorer

1 Answer

2001 explorer sport wont start


the security system has locked out.. you will have to take it to the dealer for them to unlock the system, its the only way

Nov 13, 2008 | 2001 Ford Explorer Sport Trac

Not finding what you are looking for?
2000 Ford Expedition Logo

Related Topics:

37 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

61037 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...