Question about 2001 GMC Yukon XL

1 Answer

U-joint repalcement for 2001 yukon xl

Can someone tell me how difficult it is to replace a rear end u-joint in my 2001 GMC yukon xl?

Posted by on

  • Anonymous Mar 14, 2014

    how to replace u joints on a 2001 gmc yukon



1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 6 Answers

Mark your drive shaft coincidenly with the rear axle and tranny. Remove drive shaft. Press out the old u joints and press in the new. You will need a torch for heat and a lot of patience. Have fun!

Posted on Jun 20, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

What causing the very hard loud banging noise in the rear end or in the driveline

Is there someone trapped in your trunk?
Could be your differential. Don't drive as it will really damage things.
If you are lucky its just a bad bearing on the drive shaft , those X things Universal joint. .
See u-tube on how to test a U joint.
There are needle bearings on all 4 ends of U joint.

So she said "whats a joint like you doing in a car like this??"

Sep 06, 2014 | 2001 GMC Yukon XL

1 Answer

Can i switch a 2001 gmc yukon danli xl rear end drive shaft with a 2001 gmc yukon xl

Yes, chances are they are identical. The Denali possibly has an aluminum shaft but there is no reason that you cannot interchange.

May 14, 2014 | Cars & Trucks

1 Answer

When putting truck in reverse 2001 yukon sle clunk noise in transfer case

double check u-joints before suspecting internal problem with transfeer case. Coupling between transmission and transfeer case could be worn, as well as rear slip joint on tail shaft. If not rebuilding the transfeer case yourself, get plenty of refferences before hiring some one to overhall transfercase. InMrFixIt

May 19, 2011 | 2001 GMC Yukon XL

1 Answer

I have an engine code PO332 knock sensor 2 circuit low imput bank 2 what is this problem .the car is a 2001 gmc yukon xl .

The most likely cause of your code is a bad rear knock sensor. You should check the knock sensor wiring harness for corrosion. But if that checks out the sensor will have to be replaced. The knock sensor is under the intake manifold, although it's not too difficult to remove. Both knock sensors should be replaced along with the wiring harness, just because of labor involved in gaining access to the sensors. You could try clearing the code, it may stay off for a long time.

May 23, 2010 | 2001 GMC Yukon XL

1 Answer

2001 GMC Yukon XL


Mar 23, 2010 | 2001 GMC Yukon XL

2 Answers

Gmc yukon stuck in 4 wheel drive

check all fuses if good repalce the actawaiter on the front endand it will unlock you can take it out for now and back up it will unlock too

Feb 27, 2010 | 2001 GMC Yukon XL

1 Answer

Rear view mirrors on my GMC Yukon not folding in

how do i fix the ball joints in the front end of a ford 94 aorstar

Aug 18, 2009 | 2003 GMC Yukon XL

1 Answer

Noise in rear end 2001 gmc yukon xl

broken ring gear, defective U-joint, i would go with having the U-joints checked.

Jan 09, 2009 | 2001 GMC Yukon

1 Answer

Light replacement

Just reach behind the bumper and grab the light/electrical harness and twist is either way and then it should pull out put in a new 194 bulb and you are set.

Jan 08, 2009 | 2001 GMC Yukon XL

Not finding what you are looking for?
2001 GMC Yukon XL Logo

Related Topics:

814 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts


Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides