Question about 2002 Toyota 4Runner

2 Answers

Toyota 4 runner

Hey guys I have 92 4 runner 3 liter 4 wheel drive. When I start it up I have bad knock in motor. When it warms up it goes away unless you put strin on vechile. Wondering if its known problem with these motors or if any ideas what it may be. Thanks joe

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

If this vehicle is an automatic, it could be a case of loose toque-converter bolts?
Have you ever had the transmission or engine replaced or any other major service on either? If so then have that checked first. Some good ma & pa shops will give a free estimate without lyinjg to you. Get a second and third opinion if necessary.

Posted on Dec 15, 2011

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 2,920 Answers

It sounds likem you have a rod knocking in your motor i dont know if its a known problem or not but it does sound like a rod trying to go out

Posted on Jan 17, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

Hello need info on how many oil liters do I need for the oil change toyota 4 runner V6


this toyota 4 runner takes 5.2 liters of oil and the correct oil is 5W 30 motor oil. hope this helps.

Jun 18, 2010 | 2004 Toyota 4Runner

1 Answer

Starter removal on a 1990 toyota 4 runner. Where


it is not fun w/o lift look behind passenger wheel you will need to raise front end remove wheel ,remove skid pan,and of course battery ends if 4wd I highly reccomend a lift good luck and please rate this

May 05, 2010 | 1990 Toyota 4Runner

1 Answer

Window will not roll up on 1990 toyota 4 runner


no power or no ground ??
try running a hot line to the motor

run a pair of wires from the batterie 1 pos 1 neg speaker wire will do

unplug the window motor and run it direct pos on 1 wire neg on the other flip the wires to change motor direction
if motor works then it's eithor a bad ground or a bad wire or a bad reley

Jan 01, 2010 | 1990 Toyota 4Runner

1 Answer

Can the engine bearings be changed without taking the engine out.


They can but it is not an easy job at all to try to do in the van.

Dec 14, 2009 | 1995 Toyota 4Runner

1 Answer

Where is located the KNOCK SENSOR in the 1987


The knock sensor is located on the right side (passenger) of the motor near the back, its a one wire connector probably either black or blue the sensor goes directly into the block

Sep 20, 2009 | 1987 Toyota 4Runner

1 Answer

Whining engine


It could be a pully bearing going bad, or your power stearing pump. next time you start it when it's cold try moving your steering wheel left to righ and see if there is any changes. The next time try removing your belt before you start it and see if the noise goes away. The belt could be warn out and hard itll it warms up and soften up. Start with a new belt. Good luck

Apr 06, 2009 | 1997 Toyota 4Runner

1 Answer

1990 toyota 4runner 4x4 wont lock in front wheels


your drive shaft thats turning is mabe broke or your automatic 4x4 lockers could be bad

Feb 24, 2009 | 1990 Toyota 4Runner

1 Answer

1993 Toyota 4Runner-Knocking noise-front end-cold weather


This is Caused By the Grease in the Spindle Bearings Getting frozen. Get it Greased up really Well and you Might need to Repack the Bearings on this side to Stop this and Stop further Damage to the Spindle.

Jan 17, 2009 | 1993 Toyota 4Runner

1 Answer

1992 explorer automatic hubs.Button in dash does not engage $ whe


I have the same problem with my 92' four liter explorer. I believe it has something to do with the transfer case motor behind the tranny. Under a pinch, I tapped on and around the transfer case
and tf motor, and the four-wheel drive engaged. I suspect it might be from loose wiring or a bad contact of some sort.

Nov 29, 2008 | 1992 Ford Explorer

1 Answer

92 toyota 4 runner


Low or no Transmission Oil, or
The Torque Converter gone bad, or
The Hydraulic Pump inside the transmission driven by the Torque Converter gone bad.

Sep 14, 2008 | 1992 Toyota 4Runner

Not finding what you are looking for?
2002 Toyota 4Runner Logo

168 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

70346 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6869 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...