Question about 1996 Nissan 200SX

1 Answer

After clutch replacement in 97 200sx, shifter linkage not alignin

Replaced clutch in 97 200sx. shifter linkage is approximately 1 inch out of alignment and car will not shift.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 2,920 Answers

Have the linkage reset. its not very hard to do.

Posted on Jan 17, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

When changing down from 4 to 3 the shifter will not engage


This could be a number of issues when it comes to manual transmission and clutches. Your shifter linkage may have gotten bent or now is not alligned properly or your clutch my be getting down to replacement time. It sounds more like you need to inspect your linkage but i dont know what type of car/truck ur referring to so its harder to make a for sure diagnosis.

Apr 30, 2016 | Cars & Trucks

1 Answer

Shift linkage diagram


Your linkage has come undone,climb under and reset.

Feb 02, 2014 | Nissan Cars & Trucks

1 Answer

Replace throwout barrings location install rattle when in gear.


get a service manual on CD over on ebay for about 5 bucks. jack car way up, drop the drive shaft, disconnect shifter and clutch linkage, unbolt the bell housing from the transmission and remove, unbolt pressure plate and take off flywheel, have flywheel resurfaced and reinstall, install new clutch and pressure plate, replace throwout bearing, put transmission and bell housing back in, connect shifter linkage and clutch cable or hydraulic, put drive shaft back in and you are done.

Jun 29, 2011 | 1996 Ford F150 Regular Cab

3 Answers

Automatic gear shift in 94 toyota tercel stuck


what is stuck?

the linkage or the cable from the shifter to the trans.?

block the tires so the car can not roll away...
open the hood and remove the cable from the shifter on the transmission.
see if you can manualy move the shifter on the trans.
if that moves... you may need to replace the cable (shift linkage)

Feb 19, 2011 | 1994 Toyota Tercel

1 Answer

NEED TO LOCATE ANOTHER CLIP TO REPLACE THE ONE THAT HAS BROKEN OFF THE LINKAGE. sMALL PIECE OF PLASTIC ABOUT 1 INCH IN LENGTH. 5 speed 95 Saturn SL2 LOCATED IN OR AS CLOSE TO Eden North Carolina ...


If you are writing about the shifter linkage, go to ebay and find yourself a saturn shifter repair kit.
this is a common problem, and you can do it yourself if you can get the console out. kit is less than 20 bucks.

Oct 18, 2010 | Saturn SL2 Cars & Trucks

1 Answer

Hard time getting car in gear


Sounds like your clutch may be in need of a replacement. If you cut the engine off does it go into gear easily? Then it's not the linkage.

Feb 19, 2010 | 1992 Honda Accord

1 Answer

After starting the car and pressing on the clutch, my shifter wont go into any gears, i go to put it in first and the shifter itself wont go in, what could cause this


If the shifter feels loose, the shifter linkage / damper to the gearbox became disconnected, or broken. These parts are serviceable, and should be replaced when shifting ceases to be accurate, and gears are hard to find. If the shifter feels normal, then the clutch is out of adjustment and not disengaging completely, or there is a failure of some sort inside the gearbox.

Dec 13, 2009 | 1993 Toyota MR2

1 Answer

Shifter linkage will not align on 97 200sx with standard tranny


you may have the wrong transmission type. the shifters are sort of universal on those cars. like the 5 speed can fit the se or se-r.

Jan 17, 2009 | 1996 Nissan 200SX

3 Answers

Saturn shifter linkage


Check the cable clips at the trans. Sometimes these clips come out and won't shift. Horseshoe clips that hold the cable housing.

Dec 21, 2008 | 2002 Saturn VUE

Not finding what you are looking for?
1996 Nissan 200SX Logo

Related Topics:

280 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

70387 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...