Question about 1998 Audi A4

1 Answer

Audi A4 Hi, Not able to take old battery out and insol new one should be easy but do not know how. Have new one ready for replacement, have disconected the old one out but apart from being able to perform sliding movement from left to right not able to pull it out?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has answered 20 questions.

  • Expert
  • 99 Answers

There should be either an allen key or a 13mm head bolt holding the battery clamp at the front of the battery. If this is removed, it should come out ok with a shake. i would advise help to lift the battery out as it can damage your back due to the location near the bulkhead.


Posted on Jan 21, 2009

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

May driver side power window will not let up is it my switch

you need gas replace your window motor but before you do that try to pull the window up and down if it moves then your window probably came disconected from everything thats an easy fix also you can test the window motor by puting a battery charger to the connections if the motor works it may be your switch I doubt its your switch its very rare that those go bad I have replaced a lot of window motors they are quick and easy good luck with your singing career

Dec 22, 2012 | Cars & Trucks

1 Answer

2001 BMW X 5 replace battery now it wont start

Starter solenoid. Put a new starter on it and try it out.

May 05, 2010 | 2005 BMW X5

1 Answer

I need to know how to replace the rear main seal in a 1993 jetta toinght i all ready have the parts

short answer is the transmission has to come out then its easy after that just pull the old seal out and tap the new one in place

Mar 14, 2010 | 1993 Volkswagen Jetta

2 Answers

No start

INFO: Sounds like you may have blown a fuseable link. RECOMENDATION AND LOCATION: Check the fuse block located on the drivers side fenderwell, in this location you will find fuses and fusible links. This is a wire with which seems to have a thick insolation on it. To test you can pull the wire to see if it still hase a wire in it, if the link is blown there will be only insolation. . Hope this tip helps.


Mar 02, 2010 | 1992 Ford Escort 4 Door

2 Answers

How to switch out the battery

Remove Negative terminal first, then positive terminal. Battery will have some type of tie down or block at base with a bolt you will have to remove. Remember how it goes back together. Remove battery.
Install new battery and tie down or block. Install Positive terminal then Negative terminal.
Remember to never touch both Positive and negative terminals with a metal object (ie..ratchet, wrench etc) this can cause injury and/or permanent damage to a new battery.

Nov 27, 2009 | 1995 Eagle Vision

1 Answer

Change radiator

Hi ,
Yes you do have to remove the bumper and ,Air-con rad(do not disconect!!)move to offside carefully still attached and Power steering cooling pipe(do not disconect) move to nearside.Lots to undo but easy enough if car raised on axle stands or ramp.

Jul 11, 2009 | Audi A5 Cars & Trucks

1 Answer

Chevy blazer tahoe v6 4.3 vortec won't even give me a light

any losen weire araund starter?on starter hawe 3gray fusebel link weire and hawe to conect with same weire from batt big red weire.if are conected chek gray 3 weire by sleigty poling on weire and see if is brocken samtime brick iseide under insolation and yu cant see disconect batt before inspection

Mar 12, 2009 | 1993 Chevrolet S-10 Blazer

1 Answer

Need to replace number 1 sensor

Hi, it is very easy to change but have go repair shop, first when u get sensor, they have to heat the sensor with gas light that use in welding, the neck right from where it tied the manifold and put small engine oil, then start losing it, and dont forget to remove the battery terminal when doing the work,when it lose then disconect the wire that is connected to the point where it is connected and fix the new one by tieting it firmly to the position and fix back the wire and battery head and start the car u will see that the check engine light is gone



Dec 31, 2008 | 2001 Ford Windstar

1 Answer


Hi ,replaing your sterter can be easy ,disconect your battery positive cable disconect the big cable at the starter, then the small one ,now remove the two screws that hold the starter in place,just take it out ,installation is the reverse procedure .. good luck......

Aug 06, 2008 | 2004 Chevrolet Cavalier

1 Answer

Need to replace positive battery cable

ok disconect the old one complety from the battery FIRST then the starter motor, on your new positve put you conectors on then connect to the starter motor FIRST then to you battery make sure there all tight then your ready to go

Jun 08, 2008 | 1987 Nissan Pathfinder

Not finding what you are looking for?
1998 Audi A4 Logo

Related Topics:

77 people viewed this question

Ask a Question

Usually answered in minutes!

Top Audi Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers


Level 3 Expert

70374 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

13564 Answers

Are you an Audi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides