Question about 1994 Isuzu Rodeo

1 Answer

My door locks don't work, and my remote will only open the driver

All my door lock buttens stopped working even with the remote. I can open the driver door with the remote, but that is the only one that will open. Every other door I have to open and close manually and the driver door witl only open with the remote, not lock.... .

Posted by on

  • warfield846 Jan 30, 2009

    my remote will not open my new car door

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 9 Answers

Check door switch connection under door pad in drivers door. Sounds like the electrical connection that sends power from the main door (drivers side) to other door has failed or wiggled loose.

Posted on Feb 02, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Central locking 2005 subaru liberty stopped working on 2 doors


1. Replace battery in remote
2. Replace sensor at rhf door lock (it is inside of door)

Apr 30, 2014 | Cars & Trucks

1 Answer

2004 honda accord driver side lock won't open remote


driver side has most use and breaks down quickest.
Typically, the lock wears, and should be oiled using graphite powder, not oil, as with most outdoor locks.
However, in winter moisture turns to ice and freezes lock.
In this case, try to squirt lock de-icer (usually this is methyl alcohol or some other type).
Don't use an alcohol (such as from drugstore) that also contains water.
that would make matters worse.
If you spray enough lock deicer or even a high-quality penetrating oil, you may be able to work key and lock to a point where you can turn it.

Don't force key rapidly or too strongly, as it will bend, and may break off in lock.

You can spray some alcohol or penetrating fluid on the key to work it into the lock better.
Sometimes, you can get at a frozen lock mechanism by spraying down into **** between window and metal door from above lock.
Sometimes, you might find that the door itself is frozen,
or the lock latch is frozen, and not the key-tumbler.
In this case, you can try body-checking (not kicking) the door,
to loosen the frozen edges around door and window.
If you can get into car from other side, you can sometimes open it from inside to break ice-jam.

If this is an electrical problem
(only remote doesn't work)
The likely cause is broken wire in wire-harness from car body to door.
There will usually be a group of wires either inside a cable or bundled in a rubber tubing, going from car to door at front between hinges.
Here is where the electrical connection will be broken,
because the wires break eventually as they get flexed over and over.

IN this case, the only permanent fix is to find the wire (it will be color-coded), and replace at least 6 inches of that wire (it will probably be broken inside insulating sheath.)
Alternately, there may be an open-circuit at connector to door-latch solonoid. Here you might get lucky if you get inside door-cover off and wiggle or re-insert the plug connector.
Also possible that solenoid is just burnt out or open-circuit.
In that case it must be replaced, for the remote signal to effectively open door lock.

Jan 26, 2012 | 2004 Honda Accord

1 Answer

Doors wont lock. Windows won't work. Car thinks the door is locked because when I open the hood alarm goes off. Security light is flashing when doors are closed. Locks don't engage when driving...


Window fuse's and relay's may be up under driver or passenger side dash or behind glove box, under the hood and even under the seats, and finally on the ends of the dash. All passenger power windows and locks are controlled thru and get power from the master control switch on the drivers door. Could be a broken wire in the rubber boot going from the door to the body. You will have to eliminate each till you find the culprit. Check that all switches return to neutral when released. It could also be the body control module.

Aug 28, 2011 | 2003 Volkswagen Jetta TDI

2 Answers

How do I get my key remote to lock/unlock my toyota rav4 2002 model? I changed the battery because I thought that was the problem but it is still not working. The red light on the remote comes on but then...


You will need to try reprogramming the remote 1st, below is the complete procedure. If the reprogram doesn't restore function then you will need the dealer to test the keyless entry system, you may have a bad module or remote (only applies if both remotes don't work).

Start with the key out of the ignition, drivers door is open all others closed and
drivers door is unlocked.

2. Perform these steps within 5 seconds.
A. Insert the key into the ignition(Do NOT Turn) Pull key out.
B. Insert the key into the ignition(Do NOT Turn) Pull key out.

3. Perform these steps within 40 seconds.
A. Close then open the drivers door.
B. Close then open the drivers door.
C. Insert the key into the ignition(Do NOT Turn) Pull key out.

4. Perform these steps within 40 seconds.
A. Close then open the drivers door.
B. Close then open the drivers door.
C. Close the drivers door
D. Insert the key into ignition and leave it in ignition.
E. Turn the ignition to ON (Do NOT Start) then back to OFF.
F. Remove the key from the ignition.

5. Within 3 seconds, the power door locks should lock then unlock automatically
indicating successful entry into programming mode.
Return to step 1 if the locks do not cycle at this point.

6. Perform these steps within 40 seconds.
A. Press the lock and unlock buttons on the remote simultaneously for 1.5 seconds.
B. Immediately after letting go of the lock and unlock buttons,
Press the lock button by itself and hold for 2 seconds. Within 3 seconds, the door
locks should lock and then unlock once indicating successful programming. If
the door locks cycle twice, repeat steps A and B in step 6 as the remote was
not accepted.
C. Repeat steps A and B in step 6 for each new remote.

7. Open drivers door.

Aug 24, 2011 | 2002 Toyota RAV4

2 Answers

2000 Toyota Sienna Minivan car alarm goes off.


1. Start with key out of the ignition, drivers door is open all others closed and
drivers door is unlocked.

2. Insert key into ignition (Do not turn) and pull it out.
3. Perform these steps within 40 seconds.
A. Using the power door lock switch on drivers door perform 5 lock/unlock cycles starting
with lock. Use an even pace and try to go about one cycle per second.
(1 cycle = 1 lock and 1 unlock.)
B. Close, then open drivers door.

4. Perform these steps within 40 seconds.
A. Using the power door lock switch on drivers door perform 5 lock/unlock cycles starting
with lock. Use an even pace and try to go about one cycle per second.
(1 cycle = 1 lock and 1 unlock.)
B. Insert the key in the ignition cylinder.
C. Turn the ignition to ON (Do NOT Start) then back to OFF.
D. Turn the ignition to ON (Do NOT Start) then back to OFF.
E. Remove the key from the ignition.

5. Within 3 seconds the power door locks should cycle automatically indicating successful entry
into programming mode. Return to step 1 if the locks do not cycle at this point.

6. Perform these steps within 40 seconds.
A. Press the lock and unlock buttons on the remote simultaneously for 1 second.
B. Immediately after letting go of the lock and unlock buttons,
Press the lock button by itself and hold for 2 seconds. Within 3 seconds the door locks
should cycle once indicating successful programming. If the door locks don't cycle or
cycle twice, repeat steps A and B, your remote has not been accepted.
C. Repeat steps A and B in step 6 for each new transmitter.

7. Close drivers door.

Apr 25, 2009 | Chevrolet Malibu Cars & Trucks

3 Answers

The Lexus car remote key control model ES300


try this:

1. Start with key out of ignition, drivers door is open all others closed and
drivers door is unlocked.

2. Insert key into the ignition (DO NOT Turn) and Pull key out.
3. Perform these steps within 40 seconds.
A. Using the power lock switch on the drivers door, perform 5 lock/unlock cycles
starting with lock. Use an even pace and try to go about one cycle per second.
(1Cycle = 1 lock and 1 unlock).
B. Close, then open drivers door.

4. Perform these steps within 40 seconds.
A. Using the power lock switch on the drivers door, perform 5 lock/unlock cycles
starting with lock. Use an even pace and try to go about one cycle per second.
(1Cycle = 1 lock and 1 unlock).
B. Insert the key in the ignition cylinder.
C. Turn the ignition to ON (Do NOT Start) then back to OFF.
D. Remove the key from the ignition.

5. Press any button on remote for a minimum of 1 second.
System should now lock and unlock doors once.

6. Close and open drivers door.

7. Press any button on remote for a minimum of 1 second. System should now lock and
unlock doors. Once to confirm programming, twice to indicate programming failed.

8. Repeat steps 5, 6 and 7 for additional remotes.

Mar 23, 2009 | 1997 Lexus ES 300

3 Answers

Program remote control for mazda mpv 2002


Courtesy of: forums.mazdaworld.org

Try this, it works on several 2002 models:


Step 1: Open drivers door and leave open.

Step 2: Lock and unlock the drivers door using the power door lock switch on the door.

Step 3: Insert key into the ignition.

Step 4: Turn key to on position and return to off position. (IMPORTANT - use ON position NOT ACC position). Do this 3 times within 10 seconds. Leave key in the ignition.

Step 5: Open and close the drivers door 3 times. (Door should be left open after this step).

Step 6: ECU should respond by locking and unlocking the doors.

Step 7: Press any button on remote #1. ECU responds by locking and unlocking the car doors.

Step 8: Press any button on remote #2 (etc.) Each time the ECU will respond by locking & unlocking the doors.

Step 9: Remove the key from the ignition and the ECU will respond a final time with a series of door locks and unlocks. You're done

Dec 06, 2008 | 2000 Mazda MPV

1 Answer

Driver side door lock stopped working


sounds like the lock motor is locked up or probably broken connectors yo have to open the door panel to check this out.

Nov 14, 2008 | 2001 Volkswagen Jetta TDI

1 Answer

2001 Ford Taurus door locks


The electric motor that pulls the lock button up and down has failed, you will need to pull the door panel to replace it. Yes it is fairly common.

Jul 28, 2008 | 2003 Ford Windstar

Not finding what you are looking for?
1994 Isuzu Rodeo Logo

Related Topics:

836 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...