Question about 2007 Chevrolet Equinox LS New Cars

1 Answer

Software program Hello , I wont to ask about the software program that can use to connect the engine of chevy with computer to check it and see the data of your engine and reset some things ,anybody has this software ??Thanks for help..

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,509 Answers

Most of the time mechanics use a scanner as the programs are (garded) by the vehical manufactures OTC , Snap-on tools. You want a unit that will see the data stream not just retreive and reset codes. Lap-top programs can be shopped for on the internet but the dianostic machaines (scanners) have trobleshooting and different dianostic cables and you may decide that if your going to make this kind of investment in tools them you had better be ready to make a living at it. Alot of stops don't have a laptop program because of the casts ( most dealers have a manufactures interface ) Until there is somekind of breakthough the cast is too high and the updates can be higher

Posted on Aug 21, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I replaced the TCM in my 2005 Chevy colbolt, light come on but car won't start, turn key and anti theft icon comes on but doesn't stay on


TCM ? transmission control module ? Did you have it programmed ? Reprogram the TCM. Refer to Control Module References for programming and setup information.
Transmission Control Module Programming and Setup
The transmission control module (TCM) must be programmed with the proper software/calibrations. Ensure that the following conditions exist in order to prepare for TCM programming:
• The battery is fully charged.
• The ignition switch is in the RUN position.
• The Techline equipment cable connection at the data link connector (DLC) is secure.
Program the TCM using the latest software matching the vehicle. Refer to up-to-date Techline equipment user instructions.
If the TCM fails to program, proceed as follows:
3.1. Ensure that the TCM connection is OK.
3.2. Inspect the Techline equipment for the latest software version.
3.3. Attempt to program the TCM. If the TCM still cannot be programmed properly, replace the TCM.

Feb 08, 2017 | 2005 Chevrolet Cobalt

1 Answer

On a 94' chevy 350, what controls the air/fuel ration with the timing


The engine computer ,with inputs from engine sensors ! Mass air flow sensor , map sensor , coolant temp sensor , Throttle position sensor , crankshaft position sensor , cam sensor etc.... through software programmed into the PCM .

Sep 04, 2015 | Cars & Trucks

1 Answer

I have a 2000 Chevy Blazer. The check engine light is not on. It starts up fine and drives fine, but when I come to a stop it stalls. starts up fine and drives fine no backfires or puttering wont idle


fuel filter or fuel pump chevy didn't add fuel pressure sensing to its ck engine computer till 2011

and sorry to tell ya but blazers have a common prob with fuel pumps going bad , just ask a parts guy on how many he sells a year , you;ll get the sad story

Apr 20, 2015 | Cars & Trucks

2 Answers

2006 cheevy colorado reduced powereduced power wont run 2006 chevy colorado pick up code 600 and 601


Those are communication and internal computer failures. You likely need a new PCM

Jan 01, 2015 | 2006 Chevrolet Colorado

2 Answers

CRANK ANGLE SENSOR


Try checking the computer. Some of them were located behind the glove box. If you can open it, look at the computer chips. If one is burnt you will see it.

Nov 20, 2013 | Chevrolet Cars & Trucks

2 Answers

ASTRA DIESEL1.7 CDTI 2006 WONT RESTART WHEN WARM RUNS FIN ALL DAY BUT WONT START AGAIN FOR 1-2 HRS


Common rail engine controlled by a computer ,for some reason it sounds like a temperature sensor faulty but what one and where? Best advice here is ask at the dealer or a bosch agent as it will need the right software to locate the fault

Apr 14, 2013 | Cars & Trucks

1 Answer

Is the car locking system programed into the key or engine software? I had my key socket exchanged recently, after a while I had a message that "immobilizer failed check the manual". The car...


key programming is seperate on older vehicles with a seperate transponder and transponder reader but integrated on newer models ,return car to garage and ask them to look at it again but if it was a software upgrade on the computer then their are new laws within the EEC regarding the self locking of cars and some member countries have been lobying against it and want it removed from cars as its dangerous in a accident ,so i honestly couldnt say as to weither this vehicle was re-programmed to current europeon norms,personally after getting burnt trying to get some kids out of a locked car in a accident and watch them burn to death as the gas tank went up and i couldnt get close enough with anything in my hand to smash the window glass iam in favour or removing self locking doors

Apr 06, 2011 | Volvo S40 Cars & Trucks

1 Answer

Hello. i have a 2000 E 270 CDI automatic transmission mercedes-benz. i want to reset the transmission and i don't know how. if u pls help me solve this. thank u


I can advice you only this can do in Mercedes dealer workshop, By Mercedes Benz diagnostic computer, you ask them you need to software update and reset your adaptation data in your transmission and engine control units, when you do the transmission you have to do the engine software update too otherwise it can make software clash between two control modules, if software version different, is this information helped you?

Oct 20, 2010 | 1999 Mercedes-Benz E-Class

1 Answer

I have recently changed the cluster on my 2004 Chevy Trailblazer but it's asking me for a code, how can i find that code and how do i input it in order to get the gauges working?


Hello and welcome. the dash cluster has a internal processor just like a home computer. the cluster has to be programmed with software for it to function correctly. programming requires a GM tech 2 scan tool, a service programming system and access to GM software. any GM dealer can program the cluster, it will cost between $50.00 and $100.00 to have it programmed

Sep 11, 2010 | 2004 Chevrolet TrailBlazer

Not finding what you are looking for?
2007 Chevrolet Equinox LS New Cars Logo

103 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

70346 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6864 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...