Question about 1995 Ford F350

2 Answers

Fading brake pedal

I have a 1995 ford f-350 diesel 2 wheel drive dually , and when i push on the brake pedal the pedal will slowly go to the floor I have replaced the master cylinder, pads and rear shoes including all the hardware front and rear, Ihave checked the vaccume at the booster and have plenty, I also replaced the check valve that goes into the booster, collectivly I have ran 2-3 gallons of brake fluid the system and no air in the system, afterall that Istill have the same problem that I started with. I pull a trailer alot between april and october and as of now I can barely stop the truck letalone the trailer and truck. any help would be appreciated

Posted by on

  • 2 more comments 
  • aarnold3car Jan 17, 2009

    pedal is stiff when the brakes are first applied then pedal will start going to the floor. no fluid leaks and the pads adjusted up

  • aarnold3car Jan 18, 2009

    the truck has a proportioning valve that threads in the rear port of the master cylinder and a rear anti lock brake valve on the frame 1 foot under the master cylinder. There is also a rear ABS sensor (R.A.B.S.) in the center and on top of the rear end housing

  • work4it1 May 11, 2010

    ok well does it have abs at all or a load/height proportioning valve on the frame rail any where ?

  • work4it1 May 11, 2010

    Make sure that the rear shoes are adjusted up. I take it that there are no leaks ? the next step is to take a vise grip and pinch off the rear brake hose at the diff see is this makes the pedal hard if not try it on the front one wheel at a time .

×

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 196 Answers

Perfect well at this point i would say that tha abs valve is bypassing fluid. If you can un hook the line that comes into the abs valve and plug it and try and bleed the system where you cap the line going into the abs valve. If you get a good pedal after pluging the line going into the abs valve this tells me that the abs valve is bypassing fluid give it a try i have ran into this a few time and the abs valve has been bad. Also can you rate this sluton also i do hits on my own free time thanks good luck

Posted on Jan 18, 2009

  • Custom tbird May 28, 2012

    I've gone threw several master cylinders and the pedal still goes to the floor even after all new pads shoes rotars and drums but the master cylinder doesn't lose break fluid plz help i can't figure this out

×

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 3 Answers

Sounds like a bad master

Posted on Jan 17, 2009

  • lowlife1972 Jan 19, 2009

    it also could be the master leaking off inside i had the same issue on a 98 suburban

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

95 f350 hard brake pedal


did you get your brakes fixed? If so what was wrong?

Nov 05, 2011 | 1995 Ford F350

1 Answer

1994 F350 7.5 Dually 2wd I replaced the master cylider with a rebuilt. New rear hubs and shoes. I have bled the systen 2 separate times per repair manual. There is no brake fluid leaking any where....


I have the same problem,, put all new brake components on truck, needed it anyway,, found out that the booster is not designed for a diesel application,, ford made a model change for the diesel,, number from ford is F 5 T Z - 2005 CA a zero loss booster,, have ordered on will put on when arrives, $240. good luck,,

Sep 12, 2010 | 1994 Ford F350 Crew Cab

1 Answer

1994 Ford F 350 4X4 Diesel. Brake pedal goes to


You need to crawl under the truck and inspect each brake line for leaks. You also need to check wheel cylinders and calipers. The chances are pretty good that you will find a small leak in a line or a wheel cylinder leaking, pay close attention to the rear of the truck because that is normally where these problems occur. Hope this helps.

Jul 10, 2010 | 1994 Ford F350 Crew Cab

1 Answer

Brake fade on a 1988 ford E350 motorhome


You might want to google recalls on the internet.
( http://www.recalls.gov/nhtsa.html )

I remember one such on that or the F-53 chassis.

Jun 02, 2010 | 2007 Ford E-350 Super Duty Length XLT

1 Answer

Hi, I have a 1997 Ford F-350 diesel and the brake


common problem! replace the brake booster! and vacuum pump!

Jun 02, 2010 | 1997 Ford F350 Crew Cab

1 Answer

83 Ford F350diesel dually truck brake problems


you must have a leak in your brakes! check your brake fluid! They may work for now but after all your brake fluid is pushed out they wont work. You better take a look underneath and get someone to press on the brakes to see where it is leaking out. You can keep toping up the brake fluid and that might get you by for a while.

Dec 28, 2009 | 1982 Ford F 350

1 Answer

1992 Ford F350 Dually Diesel Truck Brake System problem.


Adjust your rear brake shoes. Then rebleed the system. Start at the master cylinder Bleed master first then the wheel furthest away from the master (right rear then left rear then right front then left front. Do that and your pedal should be good.

Nov 28, 2008 | 1992 Ford F350

2 Answers

1989 Ford F350 2 wheel drive dually 460 ci gas motor


5 Inspect Brake Fluid Type Brake fluid loss or contamination grey_line.gif 10 Inspect Master Cylinder (Brake System) Worn or leaking brake master cylinder. grey_line.gif 11 Inspect Brake Power Booster Damaged booster vacuum line/check valve, or diaphram

Nov 24, 2008 | 1989 Ford F 350

Not finding what you are looking for?
1995 Ford F350 Logo

1,027 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...