Question about 1992 Honda Accord

1 Answer

Where is the valve cover? - 1992 Honda Accord

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 740 Answers

TOP OF THE ENGINE - where sprk plug wires go into the top of the engine thats your VALVE COVER...

Posted on Jan 16, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2004 Bmw x5 valve cover torque specs


valve cover gasket torque spec? - Bimmerforums

www.bimmerforums.com/.../showthread.php?...valve-cover...torque-spe...
Dec 7, 2012 - Remember the little rubber grommets around the cover bolts? ... Location: alabama; Posts: 5,537; My Cars: 2002 bmw 325 ... Torque spec for the M52 valve cover bolts is 89 inch-pounds / 7.4 ... 1976 - 1989 (E24) · 2004+ (E63, E64) ... 2012+ X1 (E84) · 2003+ X3 (E83,F25) · 1999+ X5, X6 (E53, E70, E71). Valve Cover Bolt Torque Specs
Oct 25, 2014
Valve cover screw torque specs?
Nov 9, 2012
leaking valve cover gasket
Dec 29, 2011
How specific for torque specs?
Dec 27, 2011
More results from www.bimmerforums.com

Nov 06, 2015 | Cars & Trucks

Tip

Simple steps to replace the Valve Cover Gaskets on a Jaguar XJ8?


Replace the valve cover gasket if the valve cover gaskets are leaking or if they're worn. The procedure is as follows:--
1)First carefully remove the nuts holding the valve cover to the engine head.2
2)Then pull the valve cover off from the engine head .
3)You can use flat-tip screwdriver to remove the valve cover.
4)It will be very dirty inside so you will have to clean the mating surfaces on both the engine head and the valve cover.
5)Take your time and clean it completely.

6)You can use a bead of RTV sealant on both mating surfaces.

7)Then carefully seat the gasket to top of the engine head.
8)The gasket can only be fitted in one way. So fit it properely.
9)Then tightly Press the valve cover to the gasket
10)And tighten the valve cover nuts secure.

This will help.Good Luck.

on Mar 10, 2010 | Jaguar XJ8 Cars & Trucks

1 Answer

Valve cover won't come off


Follow the detailed procedure mentioned in the link below to remove replace VALVE cover:----
Click the link below:---
VALVE COVER GASKET REMOVAL GUIDE http://technoanswers.blogspot.in/2012/06/valve-cover-gasket-removal-guide.html

-----------
For more help on these issues,check the link below:---
Car oil leaks from valve cover gasket? http://schematicsdiagram.blogspot.com/2011/12/car-oil-leaks-from-valve-cover-gasket.html

--------
Lexus RX: Tapping noise under Valve Cover At Low RPM? http://technoanswers.blogspot.in/2012/04/lexus-rx-tapping-noise-under-valve.html
---------- How to replace Timing Belt,Water pump And Valve Guides on Mitsubishi Montero http://repairhelpcenter.blogspot.com/2012/10/how-to-replace-timing-beltwater-pump.html

----------
2000 Toyota Solara: Valve Cover Gasket Replacing? http://technoanswers.blogspot.in/2012/04/2000-toyota-solara-valve-cover-gasket.html

----------
Valve Cover Keeps Cracking? http://schematicsdiagram.blogspot.in/2012/04/valve-cover-keeps-cracking.html

----------
These details will help.
Thanks.

Nov 23, 2012 | 2006 Subaru Forester

1 Answer

Can't get valve cover off to replace the PVC valve.


RECHECK MAKE SURE ALL VALVE COVER BOLTS BEEN REMOVED. LOOK AT THE NEW VALVE COVER GASKET COUNT BOLT HOLES IN NEW GASKET IF YOU COUNT SAME AMOUNT BOLT HAS BEEN REMOVED. VALVE COVER STUCK TAKE A RUBBER HAMMER TAP VALVE COVER TO BREAK THE SEAL.DONT PRY VALVE COVER YOU WILL DAMAGE VALVE COVER AND SEAL SURFACE CAUSING YOU TO GET A OIL LEAK.

Aug 09, 2011 | 2008 Hyundai Elantra

2 Answers

How to replace valve cover gasket


Remove the valve cover, which is a simple bolt on component. Remove the old gasket and install the new one.

May 13, 2011 | 2004 Suzuki Forenza

1 Answer

Leaking valve cover gaskets - repair estimate $1000.00. Is it worth it?


no it is not worth that much, you can do it yourself for about 20-40 dollars (price of the gaskets)

follow these for better instructions go to www.autozone.com and register to become a member
this will give you access to their repair database there you can specify your car and get repair info.

Removal & Installation2.0L Spi Engine
  1. Loosen the clamp and disconnect the engine air cleaner to valve cover hose from the valve cover.
  2. Remove the two ignition wire separators from the valve cover. Position the spark plug wires aside.
  3. Remove the three valve cover bolts and remove the valve cover and gasket.

To install:

CAUTION Do not use abrasive grinding discs to remove gasket material; only use manual scrapers. Do not scratch or gouge aluminum sealing surfaces or oil leaks may occur.

NOTE Do not use any sealer with a silicone-type gasket.
  1. Install the three valve cover bolts and remove the valve cover and gasket.
  2. Install the two ignition wire separators from the valve cover.
  3. Tighten the clamp and disconnect the engine air cleaner to valve cover hose from the valve cover.

2.0L Zetec Engine
  1. Disconnect the crankcase ventilation hose from the fitting on the valve cover.
  2. Disconnect the wiring connector at the oil control solenoid.
  3. Disconnect the speed control (if equipped) and the accelerator control cable.
  4. Position aside the accelerator cable.
  5. If equipped, disconnect the speed control cable from the bracket and position aside.
  6. Remove the ignition wires from the spark plugs.
  7. Remove the bolts and position the upper timing belt cover away from the valve cover.
  8. Remove the valve cover.
  9. Fully loosen the ten bolts.
  10. Remove the valve cover and valve cover gasket.
  11. Inspect the valve cover for damage. Install new cover as required.
    CAUTION Do not scratch or gouge aluminum sealing surfaces or oil leaks may occur.
  12. Clean and inspect the sealing surfaces of the valve cover and the cylinder head. Both surfaces must be clean and flat.

To install:
  1. The valve cover gasket and the valve cover must be installed and the bolts tightened to specification within four minutes of sealant application.
  2. Apply a 0.1 inch (3mm) bead of silicone sealant in two places where the front camshaft bearing cap meets the cylinder head.
  3. Install the valve cover.
  4. Position the valve cover gasket.
  5. Position the valve cover.
  6. Tighten bolts in the sequence shown.

    0996b43f80204dc3.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. The proper torque sequence for the 2.0L DOHC Zetec engine

  7. Install the upper timing belt cover bolts.
  8. Install the ignition wires.
  9. Connect the oil control solenoid connector.
  10. Connect the crankcase ventilation hose.
  11. Connect the speed control (if equipped) and the accelerator control cables.
  12. If equipped, connect the speed control cable to the bracket.



May 13, 2011 | 2001 Ford Escort ZX2

2 Answers

Valve cover is leaking oil on my 2000 1.9 TDI Passat. Have changed the gasket but still leaking badly. Have been told to change whole cover but VW want £120,00 Any ideas?


will try to help.if it's only the valve cover leaking,i'm guessing they sold you the rubber one that says ne rtv sealant needed. take your back off, try not to break the rubber seal when removing!clean the top of head where gasket goes. clean the valve cover really good!clean the grooves out that the gasket slides into. buy some blue trv glue, apply a thin coat to top of head, let it setup while you apply another thin coat to valve cover, let set 10mins. apply gasket to valve cover making sure to push the gasket into the grooves on valve cover. don't worry about neatness. let the valve cover set on a hard surface with the gasket against the hard flat surface[such as a garage floor,or clean driveway] after10 more minutes install the valve cover,make sure and take your time. place valve cover onto motor,than hand start each bolt to insure thay are going into the prope bolt holes. after you have each bolt hand started, start at center of valve cover snugging the bolts down to motor. do not crank down or apply excessive force when tightening those bolts. you should see some of that blue rtv glue coming out around the valve cover when applying torque to the valve cover bolts. only secure them snug at first. let car set for 15mins. start car and look for leaks around the cover, do not over tighten those bolts but you may need to look for a leak, go to bolt closest to leak and turn it 1/4 at a time until leak stops. but if you do this step by step, you'll not have a leak issue. you may have pinched the gasket when you replaced it. hope this helps and thank you for choosing fixya.com

Dec 27, 2010 | Volkswagen Passat Cars & Trucks

5 Answers

Head Gasket?? Valve cover Gasket???


most likely it is the valve cover gasket. it covers the valve train where there is alot of oil to lube the top of the motor. if the head gasket was leaking it may have more signs of running poorly. also having coolant leaks also. so i will have to say valve cover gasket. now usally you may have a oil burning smell with it depending on the area of the lek but not always.

the valve cover can easily be seen when the hood is open. it is right on the top and where it meets the clyinder head is where the gasket is and the leak can be seen.

if you have more question please ask.

Nov 12, 2009 | 1997 Geo Tracker 2 Door

2 Answers

Oil leaking out of valve cover gasket


It is a Valve Cover Gasket. You can get a new one at any Auto Parts Store. To make this repair last longer, Do not get the Cheap one, Get a Felpro Gasket and it will Quadrupel the Gasket Life. Please Rate My Response! Thanks!

Jan 30, 2009 | 2001 Kia Sportage

2 Answers

I need to replace the valve cover gasket on my voltswagon jetta


you probably mean the valve head gasket.

In this case this is serious work and you should contact a local VW dealership or mechanic and have them do this work for you to insure a job well done. If you simply mean your Valve cover, then this is no big deal and can be done by taking out the 4 screws found at the corners of the valve cover and then simply lifting the cover free and replacing it with a new one/tightening the screws back down.

hope this helps :)

May 17, 2008 | 1992 Volkswagen Jetta

Not finding what you are looking for?
1992 Honda Accord Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

61037 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...