Question about 1995 Jeep Wrangler

1 Answer

1995 jeep wrangler water pump removal

How do you rmove the fan and pulley to get to the water pump?

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert that hasĀ over 500 points.


    An expert who has answered 200 questions.

  • Expert
  • 318 Answers

Remove fan belts first, then removed fan pulley bolts these are on the front center of the fan hub,,,remove these bolts.
Then remove the fan, and hub off the front of the water pump,,then remove the coolant hoses,,make sure you use a drain bucket to catch all of the antifreeze.
Then remove the water pump mounting bolts,,and gently pry off the water pump.
Then go get a new one.
Before install,,make sure you take a scraper and clean off any old gasket material first before installing the new gasket.
Then re-install the new pump.

Posted on Jan 16, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

About water pumps

most of the water pumps on cars had a hub pressed onto the pump shaft and 4 small bolts holding the pulley onto that hub
even viscous fan hubs ( fan clutch) is bolted to the hub pressed onto the shaft
comment with a photo of the water pump that has the bolt in the middle and comment on the engine make and model

Oct 17, 2015 | Cars & Trucks

1 Answer

Changing power steering motor

Remove the serp belt. Use a power steering pump pulley remover to remove the pulley. Remove the three bolts that hold the pump to the bracket. Rmove the high pressure line and the return line.

Jul 29, 2012 | 1994 Ford Aerostar Extended

1 Answer

Leaking antifreeze from the fan pully. is the fan pully the water pump

The water pump will be directly behind the fan pulley. The fan pulley mounts onto the water pump shaft. So no the fan pulley is not the water pump.
Safe Journey's,

Aug 17, 2011 | 2005 Dodge Ram 1500

2 Answers

Replace water pump on 1997 gmc jimmy 4.3 litre

there are four nuts that you must remove at the front of the pulley between the fan. remove fan, fan shroud,loosen accessory belts. remove water pump pulley and the pump bolts will be exposed. check belts for replacement while you have them loose. reverse procedure to install.

Apr 29, 2010 | 1997 GMC Jimmy

1 Answer

How do i change a water pump on 1996 grand cherokee limited V8

I'll assume you have a 4.0l

The 4.0L engine is equipped with a reverse rotation (counterclockwise) water pump. The word REVERSE is stamped or imprinted on the cover of the viscous fan drive and on the inner side of t he fan. The letter R is stamped onto the water pump impeller. When replacing water pump, ensure proper pump is installed. Installation of the wrong water pump will cause engine overheating.

NOTE:On models with 4.0 L engine, front grill must be removed to access radiator draincock. Draining cooling system can be accomplished by removing drain plug from side of block as well as by loosening radiator draincock. Drain plug is located on lower left side of engine block.

Disconnect negative battery cable. Drain cooling system. Disconnect electric cooling fan connector. Remove electric cooling fan and electric fan shroud assembly (if equipped).
Loosen, but do not remove, 4 water pump pulley-to-water pump hub bolts and 4 viscous fan-to-idler pulley nuts. Remove accessory drive belt. Remove 4 viscous fan to idler pulley nuts, and remove fan and shroud together.
Remove 4 water pump pulley bolts and remove pulley. Remove power steering pump and bracket. Disconnect heater hoses and lower radiator hose at water pump. Remove 4 water pump retaining bolts. Remove water pump.

to install just reverse procedures

Apr 05, 2010 | 1996 Jeep Grand Cherokee

1 Answer

Is there a special tool t o remove the water pump on a 1998 s-10 the bolys wont budge and they seem to have a shallow head on them

IF you are working on a 4 cylinder engine (2.2L), and if you have taken off all the preliminary stuff (fan, hoses, etc.) you probably know that the pulley under the fan is NOT the water pump pulley. The water pump pulley is just down and to the right (as you face the car) from the pulley that the fan rides on. There shouldn't be anything special about the bolts that hold the water pump in. A good socket wrench ought to handle the job.
If you are working on a 4.3L, then the water pump IS under the fan pulley. Shouldn't be anything special about those bolts either.
Hope this helps you.

Oct 25, 2009 | 1997 Chevrolet S-10 Pickup

1 Answer

How do you take fan off to get to water pump

A special fan tool is required to remove the fan from the water pump. Yes it does unscrew. One part of the tool holds the bolts of the pulley while the other part unscrews the large nut on the water pump. Tool rental is available at some auto parts stores.

Apr 24, 2009 | 1995 Dodge Ram

1 Answer

F150 1990 waterpump replacrment where do I start

5.0L, 5.8L and 7.5L Engines
See Figures 1, 2, 3, 4 and 5

0900c15280262ad7.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 1: Removing the pulley from the water pump shaft may be easier if you use belt tension to hold the pulley

0900c15280262ad8.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 2: Loosen the clamp and remove the hoses at the water pump

0900c15280262ad9.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 3: Unbolt the water pump from the timing chain cover

0900c15280262ada.jpg enlarge_icon.gifenlarge_tooltip.gif : Remove the water pump from the timing chain cover

: Make sure the gasket mating surfaces are clean and dry
  1. Drain the cooling system.
CAUTION When draining the coolant, keep in mind that cats and dogs are attracted by ethylene glycol antifreeze and are quite likely to drink any that is left in an uncovered container or in puddles on the ground. This will prove fatal in sufficient quantity. Always drain the coolant into a sealable container. Coolant should be reused unless it is contaminated or several years old.
  1. Remove the bolts securing the fan shroud to the radiator, if so equipped and position the shroud over the fan.
  2. Disconnect the lower radiator hose, heater hose and by-pass hose at the water pump. Remove the drive belt(s), fan, fan spacer and pulley. Remove the fan shroud, if so equipped.
  3. Loosen the alternator pivot bolt and the bolt attaching the alternator adjusting arm to the water pump. If applicable, remove the power steering pump bracket from the water pump and position it out of the way.
t may be easier to remove the pulley from the water pump shaft by using belt tension to hold the pulley prior to removal.
  1. Remove the bolts securing the water pump to the timing chain cover and remove the water pump.
To install:
  1. Coat a new gasket with sealer and install the water pump. Tighten the bolts to 18 ft. lbs. (24 Nm).
  2. Install the power steering pump bracket.
  3. Connect the lower radiator hose, heater hose and by-pass hose at the water pump.
  4. Install the fan shroud, if so equipped.
  5. Install the pulley, fan spacer, fan and drive belt(s).
  6. Fill the cooling system.

Apr 07, 2009 | 1990 Ford F150

1 Answer

Serpentine belt diagram for a 5.9 diesel with air and 9 pulleys

196759.jpg The 5.9L diesel engine accessory drive system (with a/c) consists of :
  1. Generator Pulley (1)
  2. Water Pump Pulley (2)
  3. Idler Pulley (3)
  4. Power Steering Pump Pulley (4)
  5. Radiator Fan Pulley (5)
  6. Crankshaft Pulley (6)
  7. Automatic Tensioner (7)
  8. A/C Compressor Pump Pulley (8)
CAUTION: When installing the accessory drive belt, the belt must be routed correctly. If not, engine may overheat due to water pump rotating in wrong direction. Refer to or for correct engine belt routing. The correct belt with correct length must be used.
1. Position drive belt over all pulleys except water pump pulley. 2. Attach a 1/2 inch ratchet to tensioner.

196757.jpg The 5.9L diesel engine accessory drive system (without a/c) consists of :
  1. Generator Pulley (1)
  2. Water Pump Pulley (2)
  3. Idler Pulley (3)
  4. Power Steering Pump Pulley (4)
  5. Radiator Fan Pulley (5)
  6. Crankshaft Pulley (6)
  7. Automatic Tensioner (7)
3. Rotate ratchet and belt tensioner clockwise. Place belt over water pump pulley. Let tensioner rotate back into place. Remove ratchet. Be sure belt is properly seated on all pulleys.

Sep 13, 2008 | 2008 Dodge Ram 3500

Not finding what you are looking for?
1995 Jeep Wrangler Logo

Related Topics:

584 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts


Level 3 Expert

77186 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides