Question about 1991 Geo Tracker

1 Answer

I just bought a 1991 chevy tracker and it needs engine oil, but i have no idea where to put the oil in, i used to have a 78 bronco and it was alot easyer to tell.

Posted by on

  • yadayada
    yadayada May 11, 2010

    the fill is on the valve cover.

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 318 Answers

The top of the engine will have a plastic or metal cap,,usually say's "OIL" will be in the middle of your engine.

Posted on Jan 16, 2009

2 Suggested Answers

  • 1 Answer

SOURCE: where do i put the engine oil in my chevy tracker

hey there, i own a 92 sunrunner and a 93 geo tracker. on both of them the oil fill cap is in the center of the engine block, closer to the fire wall. it sits a bit lower than other pieces and is inconspicuous. the check oil stick is in the front of the engine bay and has a little heart shaped piece of rubber at the top. good luck, hope this helped.

Posted on Apr 05, 2009

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need to replace an oil pressure sensor and a oil pan gasket on a 1999 Chevrolet Tracker. Which part should I replace first?


Collette, do oil pressure sensor first to make sure oil pressure is good in case it is not, then maybe you will have to change oil pump when pan off if found to be defective. Check the attached links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
2000 Chevy Tracker Oil Pan Removal Engine Mechanical Problem 2000
Removing oil pan in 2000 chevy tracker
Fix Your Chevy With Your Own Hand
Chevy Tracker Oil Pressure Switch

Jul 28, 2016 | Chevrolet Tracker Cars & Trucks

1 Answer

How to replace the tps on a 1991 tracker? the one i bought has 4 wires the one on the tracker has 6 wires


the 1991 G16a has a pig tail connector, must have 4 wires.
and shares the Injector connector (tricky pin pulls, and all)
that connector you gander is the injector /TPS connector
it has 6 pins but only 4 are for TPS. (yellow /.red are injector)
see page 3 below, for what all this means. last link below.


try to keep in mind, your car has a VIN engine code U (not 6) code 6 , has no pig tail, TPS.
GM uses U code to say, engine is 8valves, TBI, G16a , my guess, (no photos) is your bought TPS is
with tails, and is correct for your 8v engine.

Install, (need feeler gauges to do it)
it's not just thrown on to the car, it must be calibrated.
or the idle switch WILL fail.(and more)
one maker of this TPS is here: (hard to find)
SMP makes one. sMP #TH-147 is for 8V tbi.

http://www.fixkick.com/buy-parts.html#TPS
do not use 16valve parts on your car.

here is the calibration steps.
http://www.fixkick.com/sensors/tests/TPS-testing.html#8v_FSM_cal

the factory page is here
http://www.fixkick.com/TPS/TPS-p91.JPG

http://www.fixkick.com/TPS/TPS-p92.jpg

and page 3 here
http://www.fixkick.com/TPS/TPS-p93.JPG

the last page shows the tricky pin pulls....


you must pull the old pins.' one by one.
then put in then new TPS pins , in the same places of old
matching COLORS.
then do the calibration steps above, using feeler gauges.
same basic steps, from 1989 to 1998.
in 1999 they calibrate it to 0.5vdc, only.
later years, it auto-calibrates.
if the new TPS fails to cure the problem
post the symptoms, and win.

Jun 17, 2016 | 1991 Geo Tracker

1 Answer

Where is the oil pump located on a 2000 chevy tracker


THE 1.6L ENGINE OIL PUMP FRONT OF CRANKSHAFT TIMING COVER.YOU HAVE TO REMOVE CRANKSHAFT PULLEY AND WHOLE TIMING CHAIN COVER.YOU HAVE TO REMOVE OIL PAN TO REMOVE OIL PUMP PICK UP TUBE AND SCREEN.. THE 1.8L ENGINE OIL PUMP IN THE OIL PAN.YOU HAVE TO REMOVE OIL PAN TO REMOVE OIL PUMP FROM ENGINE.

Dec 08, 2010 | 2000 Chevrolet Tracker

1 Answer

Oil pressure keeps dropping? when i turn 1991 ford bronco on the pressure reads fine sometimes than it drops and the engine starts to tap. where is the pump located and how do you chANGE IT OUT?


You'll have to drop the oil pan and you will see your oil pump...Not much to replacing it either the hardest part is dropping the pan good luck and have fun wrenching...

Apr 25, 2010 | 1991 Ford Bronco

1 Answer

In my 1991 ford bronco where to I put and how much refrigerant oil to do i use


U cannot put oil in separately--it is added when you put in the refrigerant, under pressure.

Jul 15, 2009 | 1991 Ford Bronco

1 Answer

Changing rear end seal on 2000 Chevy Tracker


http://www.kick-fix.com/engine/engine-rear1.jpg

i bet a photo speaks 1M works.

next question will be how do i get there.
nut shell
oil of of tranny, oil of of xfr case.
all prop shafts off.
cross members off tranny.
tranny lift in place.
shifters all removed.(center console off)
unbolt bell housing from motor.
bingo, tranny is out.

or , put jack under tranny
pull motor.


Apr 11, 2009 | 2000 Chevrolet Tracker

3 Answers

Where do i put the engine oil in my chevy tracker


if you open the hood and look in it should be on your right hand side in the front part of the motor good luck ray

Jan 16, 2009 | 1991 Geo Tracker

2 Answers

Not getting oil pressure with first start up of day.


Sounds like the oil pump check valve is not holding pressure on the system.  It should not bleed down significantly. after 30 seconds the oil pump has regained the necessary pressur eto quiet the engine.  This is not a task I would recommend for a DIYer.

Dec 17, 2008 | 2000 Chevrolet Tracker

1 Answer

1991 tracker fuel regulator


Usually take it to a garage to have this type of test done,,,but be warned,,,if you have a lot of gasoline mixed in with your oil,,you can burn out engine components real fast here.

Oct 12, 2008 | 1991 Geo Tracker

Not finding what you are looking for?
1991 Geo Tracker Logo

Related Topics:

75 people viewed this question

Ask a Question

Usually answered in minutes!

Top Geo Experts

yadayada
yadayada

Level 3 Expert

63801 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Geo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...