Question about 1996 Ford Explorer

1 Answer

I do not have heat on the floor position of the EATC

EVERY TIME I SWITCH TO FLOOR DOESN'T WORK .EVERYTHING ELSE DOES OK

Posted by on

  • b_zelenin Jan 18, 2009

    fan works,heat works on vent and defrost. is an automatic heat system

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 149 Answers

Maybe the fans aren't working.

Posted on Jan 16, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What's the fuse number for the heater in a 2003 Lincoln Navigator? The display won't come on nor will the heat/ac. Thx


Located in the central junction box . Fuse F1.13 10amp. CJB - under right side of dash .

F1.8 10 Electronic Automatic Temperature Control (EATC) module (19980), Exterior

rear view mirror, left, Exterior rear view mirror, right

F1.5 7.5 Powertrain Control Module (PCM) (12A650), Deactivator switch, Third row

folding seat relay, left, Third row folding seat relay, right, Power lift gate

module, Brake pedal position switch (13480), Sunload sensor (19E663),

Clock (15000), Function selector switch assembly, front, Electronic Automatic

Temperature Control (EATC) module (19980). Don't think you have a fuse problem ! More then likely the HVAC control module is bad , they do go bad
Don't




Jan 05, 2016 | Lincoln Cars & Trucks

1 Answer

I have changed the radiator, heater core and the thermostat in my 1997 ford F150 but I am still blowing out cold air


THE TEMPERATURE BLEND DOOR STUCK OR BLEND DOOR ACTUATOR MOTOR FAULTY,YOU NEED TO DO A EATC DIAGNOSTIC TEST TO GET FAULT CODE SEE WHY YOU ARE NOT GETTING HEAT.TO DO A DIAGNOSTIC TEST FIRST WARM ENGINE UNTIL IT GET 120 DEGREES.WITH ENGINE OFF IGNITION SWITCH ON SIMULTANEOUSLY PRESS OFF AND FLOOR BUTTON THEN WITHIN 2 SECONDS PRESS AUTOMATIC BUTTON SELF TEST TAKE UP 20 SECONDS INDICATING BY BLANK DISPLAY WINDOW ON THE EATC MODULE. IF DISPLAY IS BLANK FOR MORE THAN 20 SECONDS OR IF CODE 888 IS DISPLAYED GO TO EATC SYSTEM TEST UNDER TESTING IF NO CODES ARE DISPLAYED AND SYSTEM IS NOT OPERATING PROPERLY GO TO SYMPTOM DIAGNOSIS IF CODES DISPLAY RECORD CODES. BEFORE TURNING IGNITION OFF EXIT SELF DIAGNOSTIC.BY PRESSING DEFROST BUTTON EXIT THE SELF DIAGNOSTIC PRESS BLUE BUTTON. IF ALL FAIL LET A GARAGE CHECK IT OUT.BUT ALSO CHECK COOLANT SYSTEM IF COOLANT SYSTEM VERY LOW YOU HAVE NO HEAT PROBLEMS.

Oct 19, 2011 | 1997 Ford F150 Regular Cab

1 Answer

Heat and aircondition.My heat and air only work on number 5


Sounds like a "fan motor speed controller" or FMSC.
Either that module has gone out...or we're not getting the signal from the control panel sometimes called the EATC.

Lincoln has an EATC (for electronic air temp control)...GMC has something similar.
There is a way to run a diagnostic test of the EATC but am having trouble finding it for GM models.

If EATC test is done and fails...it will tell you it failed and would need replacing.
If EATC passes...it will tell you it passed and the fan motor speed controller would be at fault.

Usually, when a speed controller fails, the blower motor either doesn't turn OR it runs full blast.
Both parts EATC and the FMSC are expensive.
Since yours is running full blast...at least its providing air.
I'd try to run a diagnostic check to be for sure and maybe your parts might be less expensive and available at your local parts store.

Hope this helps...

Aug 13, 2011 | 2004 GMC Envoy

1 Answer

Need location of rear blower relay 2001 expedtion


Here is the order of checking....

Power Distribution Box Description
Position 114 30AMP** for Climate Control Auxiliary Blower

** MaxiFuse


Passenger Compartment Fuse Panel
Position 7 5AMP for Aux A/C Blower Relay (via fuse 22)
Position 24 10AMP for EATC Module, EATC Blower Relay, Climate Control Switch Assembly (Feeds Fuse 7)


Also, additional details about fuses could find in ford.com/maintenance/owners_manuals

Hope helps.

Feb 04, 2011 | 2000 Ford Expedition

2 Answers

My air conditioner does not work on my 2005 f150. All the display lights turn on at the same time and none of the buttons will control air or heat. Please advise.


I would start with disconnecting the EATC / EMTC ( Electronic Automatic / Manual Temperature Control ) panel.
776465b.jpg
Open the ash tray, and pull each lower corner out, they are held on with spring clips. Working your way up the center trim panel, there are 6 ( 3 on each side- black circles in the picture above ).
When you get to the top, be cautious, the Passenger side airbag deactivation lamp has small wires on it, don't pull too hard ( green circle above )
On the back of the EATC / EMTC panel are 2 cam over connectors ( blue circles in the picture above ), release the cam tab, and they will disconnect.
When you reconnect it, it will default to off. Next is to run the self test calibration process ( pay attention to the temperature range ).

I have found some times the EATC / EMTC panel will just freeze up, and disconnecting it, and recalibrating it will make it work again. Few of them have not seen a problem again in 2+ years.
Electronic Automatic Temperature Control Module On-Demand Self-Test The EATC module on-demand self-test will retrieve on-demand (hard fault) DTCs only, it will not retrieve continuous DTCs. Continuous DTCs can be cleared when exiting the EATC module on-demand self-test. Make sure to retrieve continuous DTCs by carrying out the Electronic Automatic Temperature Control Module - Retrieve Continuous DTCs procedure before clearing any continuous DTCs.


•The EATC module on-demand self-test will not detect concerns associated with data link messages like engine coolant temperature or vehicle speed signals. A diagnostic tool must be used to retrieve these concerns.
•The EATC module on-demand self-test will detect concerns in the system control functions and will display on-demand (hard fault) DTCs for concerns that are present during the self-test. The vehicle interior temperature should be between 4°-38°C (40°-100°F) when performing the self-test. If the temperatures are not within the specified ranges, false DTCs may be displayed.
•The self-test can be initiated after cycling the ignition switch from OFF to ON. Normal operation of the climate control system stops when the self-test is activated.
•To enter the self-test, press the OFF and DEFROST buttons simultaneously and release, then press the AUTO button within 2 seconds . The display will show a flashing blower icon for 20 seconds , after which all vacuum fluorescent segments will be displayed if there are no on-demand DTCs present. If DTCs are present the EATC module will display "00 00" and then on-demand DTCs. Record all DTCs displayed.
•If any DTCs appear during the self-test, carry out the diagnostic procedure. Refer to the Electronic Automatic Temperature Control Module Diagnostic Trouble Code Index and follow the ACTION for each DTC given. See: Diagnostic Trouble Code Descriptions
•If a condition exists but no DTCs appear during the self-test, GO to Symptom Chart Condition: The EATC System Is Inoperative, Intermittent or Incorrect Operation. See: Symptom Related Diagnostic Procedures
•To exit the self-test and retain all DTCs, press any button except DEFROST. The EATC module will exit the self-test and retain all DTCs.
•To exit the self-test and clear all DTCs, press the DEFROST button. The EATC module will exit the self-test and all DTCs will be cleared.
•Always exit the self-test before powering the system down (system turned OFF). Once the self-test is exited, the ignition switch must remain ON for at least 30 seconds to allow the door actuators to automatically recalibrate.
•Continuous DTCs will be deleted after 80 ignition switch ON cycles after the intermittent fault occurs.

Electronic Automatic Temperature Control Module - Retrieve Continuous DTCs
The EATC module will retrieve only continuous (intermittent and hard) DTCs when carrying out this procedure.


•Retrieval of continuous DTCs can be initiated after cycling the ignition switch from OFF to ON. Normal operation of the climate control system stops when retrieving continuous DTCs.
•To retrieve continuous DTCs, press the OFF and DEFROST buttons simultaneously and release, then press the RECIRC button within 2 seconds . All vacuum fluorescent segments will be displayed if there are no continuous DTCs present. Continuous DTCs are indicated by the presence of the degrees Celsius symbol (°C) on the EATC module display. Record all DTCs displayed.
•If any DTCs appear, carry out the diagnostic procedure. Refer to the Electronic Automatic Temperature Control Module Diagnostic Trouble Code Index and follow the ACTION for each DTC given. See: Diagnostic Trouble Code Descriptions
•If a condition exists but no DTCs appear, GO to Symptom Chart Condition: The EATC System Is Inoperative, Intermittent or Incorrect Operation. See: Symptom Related Diagnostic Procedures
•To exit and retain all continuous DTCs, press any button except DEFROST. The EATC module will exit the retrieved continuous DTCs mode and retain all continuous DTCs.
•To exit and clear all continuous DTCs, press the DEFROST button. The EATC module will exit the retrieve continuous DTCs mode and all continuous DTCs will be cleared.
•Always exit the procedure before powering the system down (system turned OFF). Once the procedure is exited, the ignition switch must remain ON for at least 30 seconds to allow the door actuators to automatically recalibrate.
•Continuous DTCs will be deleted after 80 ignition switch ON cycles after the intermittent fault occurs.

Electronic Automatic Temperature Control (EATC) Module and Electronic Manual Temperature Control (EMTC) Module Cold Boot Process The purpose of the cold boot process is to allow the EATC or EMTC module to re-initialize and calibrate the door actuators. To carry out the cold boot process, follow the steps below.

1.Turn the ignition switch to the OFF position.
2.Disconnect the EATC or EMTC module electrical connectors.
3.Wait one minute .
4.Connect the EATC or EMTC module electrical connectors.
5.Turn the ignition switch to the ON position.
6.Select any position except OFF on the EATC or EMTC module. The EATC or EMTC module will now initialize and calibrate the mode doors. Calibration of the mode doors will take approximately 30 seconds .

May 04, 2010 | 2005 Ford F-150

2 Answers

Where is the electronicnautomatic temperature control module located on a 05 ford 150


I assume you have checked all fuses. It could be the heater control switch , the blower motor resister , I would start testing if power is getting pass the switch to the blower motor.

Nov 28, 2009 | 2005 Ford F-150

1 Answer

Heater displays everything but you cannot turn anything on ac will not turn on neither will the heat the buttons will not even light up please help


From the equipment description, I take this to be a EATC ( Electronic Automatic Temperature Control ) system.

You can try to run the EATC diagnostic test & recalibrate ( once you have confirmed it is not a fuse )

Electronic Automatic Temperature Control Module On-Demand Self-Test The EATC module on-demand self-test will retrieve on-demand (hard fault) DTCs only, it will not retrieve continuous DTCs. Continuous DTCs can be cleared when exiting the EATC module on-demand self-test. Make sure to retrieve continuous DTCs by carrying out the Electronic Automatic Temperature Control Module - Retrieve Continuous DTCs procedure before clearing any continuous DTCs.


•The EATC module on-demand self-test will not detect concerns associated with data link messages like engine coolant temperature or vehicle speed signals. A diagnostic tool must be used to retrieve these concerns.
•The EATC module on-demand self-test will detect concerns in the system control functions and will display on-demand (hard fault) DTCs for concerns that are present during the self-test. The vehicle interior temperature should be between 4°-38°C (40°-100°F) when performing the self-test. If the temperatures are not within the specified ranges, false DTCs may be displayed.
•The self-test can be initiated after cycling the ignition switch from OFF to ON. Normal operation of the climate control system stops when the self-test is activated.
•To enter the self-test, press the OFF and DEFROST buttons simultaneously and release, then press the AUTO button within 2 seconds . The display will show a flashing blower icon for 20 seconds , after which all vacuum fluorescent segments will be displayed if there are no on-demand DTCs present. If DTCs are present the EATC module will display "00 00" and then on-demand DTCs. Record all DTCs displayed.
•If any DTCs appear during the self-test, carry out the diagnostic procedure. Refer to the Electronic Automatic Temperature Control Module Diagnostic Trouble Code Index and follow the ACTION for each DTC given. See: Diagnostic Trouble Code Descriptions
•If a condition exists but no DTCs appear during the self-test, GO to Symptom Chart Condition: The EATC System Is Inoperative, Intermittent or Incorrect Operation. See: Symptom Related Diagnostic Procedures
•To exit the self-test and retain all DTCs, press any button except DEFROST. The EATC module will exit the self-test and retain all DTCs.
•To exit the self-test and clear all DTCs, press the DEFROST button. The EATC module will exit the self-test and all DTCs will be cleared.
•Always exit the self-test before powering the system down (system turned OFF). Once the self-test is exited, the ignition switch must remain ON for at least 30 seconds to allow the door actuators to automatically recalibrate.
•Continuous DTCs will be deleted after 80 ignition switch ON cycles after the intermittent fault occurs.

Electronic Automatic Temperature Control Module - Retrieve Continuous DTCs
The EATC module will retrieve only continuous (intermittent and hard) DTCs when carrying out this procedure.


•Retrieval of continuous DTCs can be initiated after cycling the ignition switch from OFF to ON. Normal operation of the climate control system stops when retrieving continuous DTCs.
•To retrieve continuous DTCs, press the OFF and DEFROST buttons simultaneously and release, then press the RECIRC button within 2 seconds . All vacuum fluorescent segments will be displayed if there are no continuous DTCs present. Continuous DTCs are indicated by the presence of the degrees Celsius symbol (°C) on the EATC module display. Record all DTCs displayed.
•If any DTCs appear, carry out the diagnostic procedure. Refer to the Electronic Automatic Temperature Control Module Diagnostic Trouble Code Index and follow the ACTION for each DTC given. See: Diagnostic Trouble Code Descriptions
•If a condition exists but no DTCs appear, GO to Symptom Chart Condition: The EATC System Is Inoperative, Intermittent or Incorrect Operation. See: Symptom Related Diagnostic Procedures
•To exit and retain all continuous DTCs, press any button except DEFROST. The EATC module will exit the retrieved continuous DTCs mode and retain all continuous DTCs.
•To exit and clear all continuous DTCs, press the DEFROST button. The EATC module will exit the retrieve continuous DTCs mode and all continuous DTCs will be cleared.
•Always exit the procedure before powering the system down (system turned OFF). Once the procedure is exited, the ignition switch must remain ON for at least 30 seconds to allow the door actuators to automatically recalibrate.
•Continuous DTCs will be deleted after 80 ignition switch ON cycles after the intermittent fault occurs.

Electronic Automatic Temperature Control (EATC) Module and Electronic Manual Temperature Control (EMTC) Module Cold Boot Process The purpose of the cold boot process is to allow the EATC or EMTC module to re-initialize and calibrate the door actuators. To carry out the cold boot process, follow the steps below.

1.Turn the ignition switch to the OFF position.
2.Disconnect the EATC or EMTC module electrical connectors.
3.Wait one minute .
4.Connect the EATC or EMTC module electrical connectors.
5.Turn the ignition switch to the ON position.
6.Select any position except OFF on the EATC or EMTC module. The EATC or EMTC module will now initialize and calibrate the mode doors. Calibration of the mode doors will take approximately 30 seconds .

Nov 27, 2009 | 2005 Ford F-150

1 Answer

My Air panel just blinks power on and off. Is


Try the self test and calibrate for the HVAC panel :

Electronic Automatic Temperature Control Module On-Demand Self-Test The EATC module on-demand self-test will retrieve on-demand (hard fault) DTCs only, it will not retrieve continuous DTCs. Continuous DTCs can be cleared when exiting the EATC module on-demand self-test. Make sure to retrieve continuous DTCs by carrying out the Electronic Automatic Temperature Control Module - Retrieve Continuous DTCs procedure before clearing any continuous DTCs.


•The EATC module on-demand self-test will not detect concerns associated with data link messages like engine coolant temperature or vehicle speed signals. A diagnostic tool must be used to retrieve these concerns.
•The EATC module on-demand self-test will detect concerns in the system control functions and will display on-demand (hard fault) DTCs for concerns that are present during the self-test. The vehicle interior temperature should be between 4°-38°C (40°-100°F) when performing the self-test. If the temperatures are not within the specified ranges, false DTCs may be displayed.
•The self-test can be initiated after cycling the ignition switch from OFF to ON. Normal operation of the climate control system stops when the self-test is activated.
•To enter the self-test, press the OFF and DEFROST buttons simultaneously and release, then press the AUTO button within 2 seconds . The display will show a flashing blower icon for 20 seconds , after which all vacuum fluorescent segments will be displayed if there are no on-demand DTCs present. If DTCs are present the EATC module will display "00 00" and then on-demand DTCs. Record all DTCs displayed.
•If any DTCs appear during the self-test, carry out the diagnostic procedure. Refer to the Electronic Automatic Temperature Control Module Diagnostic Trouble Code Index and follow the ACTION for each DTC given. See: Diagnostic Trouble Code Descriptions
•If a condition exists but no DTCs appear during the self-test, GO to Symptom Chart Condition: The EATC System Is Inoperative, Intermittent or Incorrect Operation. See: Symptom Related Diagnostic Procedures
•To exit the self-test and retain all DTCs, press any button except DEFROST. The EATC module will exit the self-test and retain all DTCs.
•To exit the self-test and clear all DTCs, press the DEFROST button. The EATC module will exit the self-test and all DTCs will be cleared.
•Always exit the self-test before powering the system down (system turned OFF). Once the self-test is exited, the ignition switch must remain ON for at least 30 seconds to allow the door actuators to automatically recalibrate.
•Continuous DTCs will be deleted after 80 ignition switch ON cycles after the intermittent fault occurs.

Electronic Automatic Temperature Control Module - Retrieve Continuous DTCs
The EATC module will retrieve only continuous (intermittent and hard) DTCs when carrying out this procedure.


•Retrieval of continuous DTCs can be initiated after cycling the ignition switch from OFF to ON. Normal operation of the climate control system stops when retrieving continuous DTCs.
•To retrieve continuous DTCs, press the OFF and DEFROST buttons simultaneously and release, then press the RECIRC button within 2 seconds . All vacuum fluorescent segments will be displayed if there are no continuous DTCs present. Continuous DTCs are indicated by the presence of the degrees Celsius symbol (°C) on the EATC module display. Record all DTCs displayed.
•If any DTCs appear, carry out the diagnostic procedure. Refer to the Electronic Automatic Temperature Control Module Diagnostic Trouble Code Index and follow the ACTION for each DTC given. See: Diagnostic Trouble Code Descriptions
•If a condition exists but no DTCs appear, GO to Symptom Chart Condition: The EATC System Is Inoperative, Intermittent or Incorrect Operation. See: Symptom Related Diagnostic Procedures
•To exit and retain all continuous DTCs, press any button except DEFROST. The EATC module will exit the retrieved continuous DTCs mode and retain all continuous DTCs.
•To exit and clear all continuous DTCs, press the DEFROST button. The EATC module will exit the retrieve continuous DTCs mode and all continuous DTCs will be cleared.
•Always exit the procedure before powering the system down (system turned OFF). Once the procedure is exited, the ignition switch must remain ON for at least 30 seconds to allow the door actuators to automatically recalibrate.
•Continuous DTCs will be deleted after 80 ignition switch ON cycles after the intermittent fault occurs.

Electronic Automatic Temperature Control (EATC) Module and Electronic Manual Temperature Control (EMTC) Module Cold Boot Process The purpose of the cold boot process is to allow the EATC or EMTC module to re-initialize and calibrate the door actuators. To carry out the cold boot process, follow the steps below.

1.Turn the ignition switch to the OFF position.
2.Disconnect the EATC or EMTC module electrical connectors.
3.Wait one minute .
4.Connect the EATC or EMTC module electrical connectors.
5.Turn the ignition switch to the ON position.
6.Select any position except OFF on the EATC or EMTC module. The EATC or EMTC module will now initialize and calibrate the mode doors. Calibration of the mode doors will take approximately 30 seconds .

Nov 02, 2009 | 2004 Ford F150

1 Answer

2007 F-150 Supercrew Lariat Cabin Air Filter


According to the shop manual you do not have one.
Air Distribution and Filtering adobe.gif Printable View (79 KB) NOTE: The air distribution system of this vehicle cannot be equipped with a cabin air filter.
There are 2 sources of air available to the air distribution system:
  • Outside air
  • Recirculated air
Recirculated air is automatically used when the electronic manual temperature control mode selector is set in the MAX A/C or OFF modes and can be selected in any mode other than MAX A/C, OFF or DEFROST by selecting the RECIRC button. Recirculated air is available in all modes except DEFROST. If the vehicle is equipped with an electronic automatic temperature control (EATC) system, recirculated air is used in OFF and is available in all modes except DEFROST. RECIRC mode is a timed function in FLOOR and FLOOR/DEFROST.
Air distribution within the vehicle is determined by the electronic manual temperature control (EMTC) function selector switch position, or is controlled by the EATC system in the AUTOMATIC mode. The air distribution mode on EATC vehicles may be overridden by the driver if desired. Air distribution doors are used to direct airflow within the heater core and evaporator core housing and the plenum chamber. An electronic mode door actuator is used to position these air distribution doors. One air inlet mode door is used to switch between FRESH or RECIRC air inlet. An electric actuator is used to position the air inlet mode door.
Air enters the passenger compartment from the:
  • instrument panel A/C registers.
  • heater outlet floor ducts.
  • windshield defroster duct.
  • side window demisters.
  • center flow-through console (if equipped).
Passenger compartment air is exhausted from the vehicle through open windows or body air vents.

Mar 08, 2009 | 2007 Ford F-150 Harley Davidson

1 Answer

Heat


replace the blower motor controller. ford part # 19e624.call your local ford parts store to get it. I am a ford technition and this is a common problem but the new part has been revised so it will last a lot longer. 9 times out of 10 this fixes the problem and a new EATC is not needed.

Feb 01, 2009 | 2002 Ford Crown Victoria

Not finding what you are looking for?
1996 Ford Explorer Logo

Related Topics:

59 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...