Question about 1984 Chevrolet S-10

1 Answer

1984 s10 2.8 manual trans. flywheel causes engine to vibrate

Changed the motor, put a 84 2.8 s10 blazer motor in a 84 2.8 s10 pickup now motor vibrates blazer was automatic, pickup was manual, i put the flywheel off the pickup on it, is that blazer motor different and unable to accept my old flywheel

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,450 Answers

No should be same engine. check your engine mounts and tranny mount. how bad a vibration? sometimes after installing engine the trans gets shifted around and if mount was worn it will allow it to hit crossmeber and vibrate.

Posted on Jan 16, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change a flywheel on a 84 bronco 2 standard transmition


is the flywheel worn out or just the ring gear, (starter gear)
first remove the trans mission then unbolt the flywheel, and replace
if only replacing the starter ring gear, use a soft hammer and bump it as you rotate the flywheel until it comes off, if the back side looks good heat it in the oven to 350 degrees and with gloves on run out and put it on the flywheel, it will go on easily, just hold it all the way on against the edge it rests on and turn it about 1/3 turn and hold for about 15 seconds and that's it, it will not come off unless you beat it off again

Mar 23, 2015 | 1984 Ford Bronco II

1 Answer

How to remove a flywheel on a 84 chevy caprice


if you have access to a hoist/lift, you simply can unbolt the trans and slide it back enough to gain access to the flywheel bolts

Sep 28, 2014 | 1984 Chevrolet Caprice

1 Answer

Am changing the transmission filter on 84 eldorado. How much transmission fluid do i need?


Hello: Put in 5 qts then drive car and get trans to operating temp then with trans in park, engine idling check fluid level again. It may need more. Have car setting level.

Aug 09, 2011 | 1984 Cadillac Eldorado

1 Answer

How do you check or change the transmission fluide in a standred shift 1985nissan pickup?


no trans fluid standard manual shift uses 90 wgt gear oil on side of trans unscrew plug if oil runs out full if not put some in it

Jul 08, 2010 | 1984 Nissan Pickup

1 Answer

I have a 84 trans am with a 305 the dipstick tube


You can see it from the under side of the engine. Its in the side of the block.

Nov 07, 2009 | 1984 Pontiac Firebird

1 Answer

Changed engine,starter hitting flywheel


did you put the shims back in the starter?

Apr 22, 2009 | 1986 Chevrolet S-10 Blazer

1 Answer

84 s10 oil pressure


Yes that switch will work. So will a lot of other parts and gaskets. You have to make sure the engine size is the same. Parts are compatible with the same engine size. Have a drain pan and new oil ready in case the oil does come flowing out.
Please remember to rate this solution.

Feb 19, 2009 | 1984 Chevrolet S-10

1 Answer

I have a 84 honda prelude cannot find TDC on the crankshaft gear need help


You line up the crankshaft at TDC byaligning the marks on the flywheel/flex plate with the pointer on the bellhousing. On the radiator side of the engine block where it bolts to the trans mission about half way up there is a rubber plug witch you can remove to gane access to the pointer on the trans bellhousing to line up the timing marks

Nov 30, 2008 | 1984 Honda Prelude

1 Answer

1984 cadillac eldorado flywheel repair


Yes obviously they will need to lift the motor because the flywheel is smack-dab in between the torque converte and motor, could actually do it yourself with the right tools ( Engine hoist, air compressor , air tools, and sockets, and or course torque wrenches to properly mount the flywheel back to manufacturer specs) but I do believe 3 Grand is way higher then your average shop. Look for shops with Mexicans they have O.K. service for a good price. Reasonable price is in between $700 and $1200 GOOD LUCK!!

Jun 24, 2008 | 1984 Cadillac Eldorado

Not finding what you are looking for?
Cars & Trucks Logo

632 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

64034 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...