Question about 1998 Buick LeSabre

1 Answer

Troubleshooting code: P0442

The PCM has determined that a small leak exists in the
evaporative emission control system.
where is the location of the purge or vent solenoid on a
1998 Buick Lesabre

Posted by on

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 49 Answers

Here ya go

Troubleshooting code: P0442 - 6b631d6.jpg

Posted on Feb 11, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Have 2009 impala ltz shuts down going down road pull over have power but starter won't engage


The starter is computer controlled by way of a relay ! When you turn the key to the start position a low voltage signal is send to the BCM - body control module , the BCM then sends a message over the GMLAN serial data network to the PCM for starter engagement , The PCM energizes the starter relay sending B+ voltage to the starter solenoid ,if there are no anti-theft system problems. The codes you have listed are emission related codes !
DTC P0455: Evaporative Emission (EVAP) System Large Leak
You must mean P0442 , because there isn't a code P0422 .
DTC P0442: Evaporative Emissions (EVAP) System Small Leak Detected
None of these would cause vehicle to shut down > Your best bet would be to take your vehicle to qualified repair shop an have diagnostics run on it .

Sep 23, 2016 | 2009 Chevrolet Impala

2 Answers

How to repair engine code po442 2009 mazda 5?


Check the purge solenoid under the hood common problem in mazda 5 6 cx7.

Jul 11, 2014 | Mazda Cars & Trucks

3 Answers

What does code p0442 mean


P0442: Evaporative Emission (EVAP) System Small Leak Detected
With a P0442, the most common repair is to:
Remove and reinstall the gas cap, clear the codes, and drive for a day and see if the codes come back.
Otherwise, replace the gas cap, or
Inspect the EVAP system for cuts/holes in tubes/hoses
China OBD2 car diagnostic tools wholesale on CareUCar

Jun 05, 2014 | 2004 Chevrolet Avalanche

1 Answer

Po442 check iight


p0442 means Evaporative Emission Control System Leak Detected (small leak)

What does that mean?
The vehicle's PCM (powertrain control module) tests the evaporative emissions (EVAP) system for large and small leaks among other conditions. In the case of this DTC, it indicates a fuel vapor leak in the EVAP control system. It means a very small leak has been detected. In fact, the leak can be from a hole as small as 0.04" in diameter. The (EVAP) emission control system prevents the escape of fuel vapors from a vehicle's fuel system. Fuel vapors are routed by hoses to a charcoal canister for storage. Later, when the engine is running a purge control valve opens allowing intake vacuum to siphon the fuel vapors into the engine.
Symptoms
The only thing you will notice is the Malfunction Indicator Lamp (MIL) a.k.a. Check Engine Light will be illuminated. You likely won't notice any drivability problems although sometimes a fuel odor may be noticed.
Causes
A code P0442 most likely means one or more of the following has happened: A loose or improperly affixed gas cap A non-conforming gas cap (i.e. not factory/original brand) A small leak/hole in a fuel vapor hose/tube Other small leak in EVAP system Faulty vent o-ring seal Defective vent valve Defective purge valve Defective leak detection pump
Possible Solutions
With a P0442, the most common repair is to: Remove and reinstall the gas cap, clear the codes, and drive for a day and see if the codes come back. Otherwise, replace the gas cap (we recommend an OEM not aftermarket part), or Inspect the EVAP system for cuts/holes in tubes/hoses More advanced troubleshooting steps include: Using an advanced scan tool, perform an EVAP leak test Verify operation of the EVAP purge solenoid / valve Perform a smoke test to see where the leak is

Oct 20, 2013 | 2007 Saturn Aura XR

2 Answers

Code says evaporator purge solenoid


Which code specifically? Do not assume you need a new solenoid. Our recommendation will depend on the specific code and some troubleshooting results. I usually recommend checking over all the EVAP vacuum lines and the gas cap too whenever there is a purge valve code. Check the vacuum lines at the cannister in the left rear bumper. I will paste info on the purge solenoid below.

P0440 Evaporative emission (EVAP) system - malfunction

Possible causes: Hose connection(s), intake leak, EVAP canister purge valve


P0441 Evaporative emission (EVAP) system - incorrect flow detected

Possible causes: Hose connection(s), intake leak, EVAP canister purge valve


P0442 Evaporative emission (EVAP) system - small leak detected

Possible causes: Hose connection(s), intake leak, EVAP canister, EVAP canister purge valve


P0443 Evaporative emission (EVAP) canister purge valve - circuit malfunction

Possible causes: Wiring, EVAP canister purge valve, ECM


P0444 Evaporative emission (EVAP) canister purge valve -open circuit

Possible causes: Wiring open circuit, EVAP canister purge valve, ECM


P0445 Evaporative emission (EVAP) canister purge valve -short circuit

Possible causes: Wiring short circuit, EVAP canister purge valve, ECM


P0450 Evaporative emission (EVAP) pressure sensor - circuit malfunction

Possible causes: Wiring, EVAP pressure sensor, ECM


P0455 Evaporative emission (EVAP) system - large leak detected

Possible causes: Hose connection(s), intake leak, EVAP canister, EVAP canister purge valve


P0456 Evaporative emission system - very small leak detected

Possible causes: Mechanical fault, hose connection(s), EVAP pressure "sensor


P0457 Evaporative emission system - leak detected (fuel cap loose/off)

Possible causes: Mechanical fault, hose connection(s), EVAP pressure sensor


P0458 Evaporative emission system, purge control valve -circuit low

Possible causes: Wiring short to earth, EVAP valve


P0459 Evaporative emission system, purge control valve -circuit high
Possible causes: Wiring short to positive, EVAP valve


Evaporative Emission Purge Solenoid

Description & Operation
The duty cycle EVAP canister purge solenoid (DCP) regulates the rate of vapor flow from the EVAP canister to the intake manifold. The Powertrain Control Module (PCM) operates the solenoid.
During the cold start warm-up period and the hot start time delay, the PCM does not energize the solenoid. When de-energized, no vapors are purged. The PCM de-energizes the solenoid during open loop operation.
The engine enters closed loop operation after it reaches a specified temperature and the time delay ends. During closed loop operation, the PCM cycles (energizes and de-energizes) the solenoid 5 or 10 times per second, depending upon operating conditions. The PCM varies the vapor flow rate by changing solenoid pulse width. Pulse width is the amount of time that the solenoid is energized. The PCM adjusts solenoid pulse width based on engine operating condition.
Removal & Installation
The duty cycle evaporative (EVAP) canister purge solenoid is located in the engine compartment near the brake master cylinder.

  1. Disconnect electrical connector at solenoid.
  2. Disconnect vacuum lines at solenoid.
  3. Lift solenoid slot from mounting bracket for Removal & Installation.

To Install:
  1. Position solenoid slot to mounting bracket.
  2. Connect vacuum lines to solenoid. Be sure vacuum lines are firmly connected and not leaking or damaged. If leaking, a Diagnostic Trouble Code (DTC) may be set with certain emission packages.
  3. Connect electrical connector to solenoid.
Purge solenoid location:

jturcotte_65.gif
EVAP cannister location:
jturcotte_66.gif

Nov 05, 2010 | 2000 Jeep Grand Cherokee

1 Answer

Code, p0442 p0445


P0442 - Evaporative Emission Control System Leak Detected (small leak)

This indicates a fuel vapor leak in the EVAP control system. It means a very small leak has been detected. In fact, the leak can be from a hole as small as 0.04" in diameter. The (EVAP) emission control system prevents the escape of fuel vapors from a vehicle's fuel system. Fuel vapors are routed by hoses to a charcoal canister for storage. Later, when the engine is running a purge control valve opens allowing intake vacuum to siphon the fuel vapors into the engine.

Symptoms: You likely won't notice any drivability problems.

Causes: A code P0442 most likely means one or more of the following has happened:
* A loose or improperly affixed gas cap
* A non-conforming gas cap (i.e. not factory/original brand)
* A small leak/hole in a fuel vapor hose/tube
* Other small leak in EVAP system
* Faulty vent o-ring seal

Possible Solutions: with a P0442, the most common repair is to:
* Remove and reinstall the gas cap, clear the codes, and drive for a day and see if the codes come back.
* Otherwise, replace the gas cap, or
* Inspect the EVAP system for cuts/holes in tubes/hoses



P0445 - Evaporative Emission Control System Purge Control Valve Circuit Shorted.
Possible Solutions: with a P0445, the most common repair is to:
* Bad or loss contact wires
* Check harnesses, replace it


Hope helps (remember to rate this).

Nov 05, 2010 | 1999 Jeep Cherokee

1 Answer

Codes p0442 & p0445


p0442
Evaporative emission control system,small leak detected

p0445

Evaporative emission control system,short in purge control cicuit

Aug 24, 2010 | 2002 Chrysler Sebring

2 Answers

I checked the codes and one comes up its po446. i dont under stand what it mean so i cant fix it to get the light to go out.


P0446 Evaporative Emission System Vent Control Circuit.
The following are descriptions of all Evaporative possible codes:

P0441 Evaporative Emission System Incorrect Purge Flow
P0442 Evaporative Emission System Leak Detected (small leak)
P0443 Evaporative Emission System Purge Control Valve Circuit
P0444 Evaporative Emission System Purge Control Valve Circuit Open
P0445 Evaporative Emission System Purge Control Valve Circuit Shorted
P0446 Evaporative Emission System Vent Control Circuit
P0447 Evaporative Emission System Vent Control Circuit Open
P0448 Evaporative Emission System Vent Control Circuit Shorted
P0449 Evaporative Emission System Vent Valve/Solenoid Circuit
P0450 Evaporative Emission System Pressure Sensor/Switch
P0451 Evaporative Emission System Pressure Sensor/Switch Range/Performance
P0452 Evaporative Emission System Pressure Sensor/Switch Low
P0453 Evaporative Emission System Pressure Sensor/Switch High
P0454 Evaporative Emission System Pressure Sensor/Switch Intermittent
P0455 Evaporative Emission System Leak Detected (large leak)
P0456 Evaporative Emission System Leak Detected (very small leak)
P0457 Evaporative Emission System Leak Detected (fuel cap loose/off)
P0458 Evaporative Emission System Purge Control Valve Circuit Low
P0459 Evaporative Emission System Purge Control Valve Circuit High
---
At least the cap isn't loose for the gas tank.

I would clear the code with an OBD-II Scanner 'erase code' button, and see how long it takes for it to come back.

Aug 06, 2010 | 1996 GMC Jimmy

2 Answers

Location of sensor for troubleshooting po442 to cause check engine light to come on


P0442 OBD-II Trouble Code - Evaporative Emission Control System Leak Detected (small leak)

What does that mean?
This indicates a fuel vapor leak in the EVAP control system. It means a very small leak has been detected. In fact, the leak can be from a hole as small as 0.04" in diameter. The (EVAP) emission control system prevents the escape of fuel vapors from a vehicle's fuel system. Fuel vapors are routed by hoses to a charcoal canister for storage. Later, when the engine is running a purge control valve opens allowing intake vacuum to siphon the fuel vapors into the engine.


Symptoms
You likely won't notice any drivability problems.


Causes
A code P0442 most likely means one or more of the following has happened:
* A loose or improperly affixed gas cap
* A non-conforming gas cap (i.e. not factory/original brand)
* A small leak/hole in a fuel vapor hose/tube
* Other small leak in EVAP system
* Faulty vent o-ring seal


Possible Solutions
With a P0442, the most common repair is to:
* Remove and reinstall the gas cap, clear the codes, and drive for a day and see if the codes come back.
* Otherwise, replace the gas cap, or
* Inspect the EVAP system for cuts/holes in tubes/hoses


46b629a.jpg

Fig. EVAP vent solenoid (2) on 3.1L, 3.4L, 3.5L & 3.8L, showing the connector (1) and vapor line (2)


510065b.jpg

Fig. EVAP canister purge solenoid location on 3.1L & 3.4L


a193655.jpg

Fig. EVAP purge solenoid valve (3) location on 3.5L




Hope this help, good luck.

May 11, 2010 | 2002 Buick Century

3 Answers

2003 Chevy Silverado 1500 Error Codes


P0135 is a bad 02 sensor
P0442 is a evap problem
P0449 is a vent solenoid

i would check the vent solenoid first its a 4ws fuse under the hood in the fuse box make sure you have power to it you should have power at all times the ground comes from the pcm i think if you fix this everything else will work they are all computer controled

Mar 23, 2009 | 2003 Chevrolet Silverado 1500

Not finding what you are looking for?
1998 Buick LeSabre Logo

2,230 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

61037 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...