Question about 1994 Isuzu Trooper

1 Answer

Cv joint replacement

1994 isuzu trooper 4wd

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 14 Answers

You have to drop the front axle, it is a lot of work.

Posted on Jul 23, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Clicking sound when in 4WD


Of coarse

Anytime a CV Boot tears the dirt & water off the
road ruins the joint & you have to replace the axle,
thus the clicking.

6 months you knew that an didn't care

As they say pay me now or pay more later

Sep 04, 2012 | 1999 Isuzu Rodeo

1 Answer

CV axle removal 1999 Isuzu Trooper


The easy way is to take the inner boot off and take the joint apart. Take new cv axle apart at inner joint and attach to the old one sticking out of axle housing. You will need to get new boot clamp.

Mar 03, 2010 | 2003 Lincoln Town Car

1 Answer

Change a cv boot on a 1996 isuzu trooper


First their are two different front axles in 1996 troopers. Isuzu changed the 4wd system from auto lock hubs to drive control axle.auto lock hube are on the older trooper's with the light and wiper switches on the dash. The same way to change both. Auto hub remove the six hex. screws slide off the hub remove the sirclip from the driveshaft. Newer hub has 6 alan-head screw's again remove them then the hubcap then the sirclip on the shaft and slide off the round spacer. Next 4 bolts from the lower balljoint and the brake's. Pull out the hub until it clear's the shaft remove the inner boot clips slide the inner boot out the shaft. Clean the grease from the end of the axle then with your fingernail feel along any of the 3 tracks in the axle and near the outer end of the track you will find a wirelike split ring slide a screwdriver under the ring and lever it off . Pull out the drive clean off the grease. You will see a sirclip on the end of the joint remove it and slide off the joint. You can replace either boot from that end. The outer joint is held on with a snap ring on the shaft inside the joint and is not easily removed need a hammer and drift to drive off the end and when removed its hard to get the snap ring on the shaft back into its place.You can change both boots from this end as well. Cheers

Sep 28, 2009 | 1994 Isuzu Trooper

2 Answers

How do i remove cv axle for a 98 isuzu trooper


Go to my profile I have just explained how to change a cv boot on a Trooper. The axle needs to be taken out to change the boot so the same solution. What you call an axle I have refered to as a drive (short for driveshaft) It takes a lot of explaining so save me a lot of writing if you read the solution I gave for changing the CV boot. Cheer's

Sep 27, 2009 | 1998 Isuzu Trooper

1 Answer

Cv joint replacement 1998 isuzu trooper 4x4


This is a simple job that is why it is not very detailed in your book. Nothing special. Do one side at a time so you have a reference to how to reassemble it. Remove your tire , brake calipers be sure not to stress the rubber brake lines or open the brake lines to air. Remove both upper and lower ball joints. When taking out the ball joints remove the cotter pin and bolt and beat the **** out of the joint for it to release. Then the C/V axles will come right out with a bit out encouragement. You will need a few tools wrenches pry bar hammer. I would buy a Chilton's or a Haynes repair manual for torque specs for reassembly. Good luck and take your time. And unless the axles are making noise you can just replace the rubber boots. Which is alot cheaper.

Jun 01, 2009 | 1998 Isuzu Trooper

1 Answer

Removing half shaft from 2000 isuzu trooper


must remove clips from inside front axle housing!! If the cv joint aint broke DONT FIX IT the boots can be replaced in less than 1 hour with hand tools and the boot is around 20$ at any parts store

Mar 31, 2009 | 2000 Isuzu Trooper

1 Answer

Loud clicking noise when 4wd is engaged on left wheel when turnin


Check your cv (constant velocity joint) , It may have a big clearance which is the source of the noise when turning left or right and when 4wd is engage. Juts like front wheel drive cars, if the cv joint is with clearance it will tend to sound in the left or right turns. It is not exactly clicking sound , nmore like knocking sound , low in pitch, but not heavy.

Nov 17, 2008 | 1996 Isuzu Trooper

1 Answer

Replacing front cv boot


I have been told that you need to take the upper/lower ball joints off to remove the whole spindle assy. Good Luck, I have the same problem.

Oct 17, 2008 | 1994 Isuzu Trooper

Not finding what you are looking for?
1994 Isuzu Trooper Logo

Related Topics:

575 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

63242 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...