Question about 2003 Lincoln Aviator

1 Answer

The floor shift to put automatic transmission in gear is loose.

The center floor console shift lever wobbles when moving it into a new position( drive, reverse, nuetral, park). How can I tighten the handle so it does not have any play in it.
When you go to put it in reverse you have to play with it sometimes to get it in the right position. I do not see any exposed set screws to tighten the lever.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Lincoln Master
  • 4,369 Answers

You have to remove the console cover to get access to the bolts that hold the shift assembly to the floor. I think there are 4.

You probably have to remove the shift bezel cover (PRNDL), remove the shift knob to get the console off.

Posted on Feb 25, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Holden cruze 2009 key stuck in the ignition won't go to off position , can't get it out of park .What is the problem ?


Is it shifter on the floor ?
Ignition Lock Cylinder Control Actuator
If the vehicle is equipped with a floor mounted console gear shifter, it has a ignition lock cylinder control actuator system in the steering column. The ignition lock cylinder control actuator's purpose is to prevent the ignition key from being turned to the OFF position when the transmission is in gear and the vehicle may still be moving. The column ignition lock system consists of a ignition lock cylinder control actuator , and a park position switch that is located in the A/T shift lock control switch. The ignition lock cylinder control actuator contains a pin that is spring loaded out to mechanically prevent the ignition key cylinder from being turned to the lock position when vehicle transmission is not in the Park position. If vehicle power is lost, and/or the transmission is not in the Park position the operator will not be able to turn the ignition key to the lock position and will not be able to remove the ignition key from the column.

GM had problems with these ! Has a TSB - technical service bulletin !
Automatic Transmission Shift Lock Control Description and Operation
The automatic transmission shift lock control system is a safety device that prevents an inadvertent shift out of PARK when the engine is running. The driver must press the brake pedal before moving the shift lever out of the PARK position. The system consists of the following components:
• The automatic transmission shift lock solenoid (serviced as the automatic transmission shift lock actuator), as well as the body control module (BCM) and the engine control module (ECM). The shift lock solenoid is located within the floor shift control assembly with vehicles equipped with floor shift.
• The BCM controls the voltage to the shift lock control solenoid through the shift lock control solenoid controlled voltage circuit. The following conditions must be met before the BCM will remove voltage from the shift lock solenoid:
- The ignition is in the ON position.
- The engine control module (ECM) sends an input via GMLAN serial data to the BCM indicating the transmission is in the PARK position.
- The BCM determines the brake pedal is applied according the brake pedal position.
Since the shift lock control solenoid is permanently grounded, the BCM supplies voltage to the automatic transmission shift lock control solenoid, mechanically locking the shift lever in the PARK position as the solenoid energizes. When the brake pedal is applied, the BCM turns the control voltage output of the shift lock control solenoid OFF, de-energizing the shift lock control solenoid. The de-energized solenoid releases the mechanical lock allowing the driver to move the shift lever out of the PARK position. When the transmission is out of the PARK position, the shift lock control solenoid remains de-energized.
During remote start operation, the BCM will energize the shift lock control circuit, locking the shift lever in the PARK position.
Replaced shifter on a cobalt , broken plastic part inside , wouldn't press on micro switch to disengage ! Found replacement shifter at auto slavage yard .$20.00 US

Sep 03, 2016 | Holden Cars & Trucks

1 Answer

Where is location the automatic transmission shift lock relay in my s10 1998 2.2 2wd


Automatic Transmission Shift Lock Control Description
The brake transmission shift interlock (BTSI) system prevents the automatic transmission from being shifted out of PARK unless the brake pedal is depressed. When the brake pedal is depressed, the BTSI solenoid releases a lock pawl. This enables the shift linkage to move and the shift lever to operate.
When service operations are required, the BTSI system can be overridden.
On vehicles equipped with a column-mounted shift lever, override the BTSI system by performing the following steps:
  1. Turn the ignition switch to the OFF position.
  2. Remove battery voltage from the solenoid.
  3. Turn the ignition switch to the ON position.
For vehicles equipped with floor-mounted shift levers, an override lever is mounted on the right side of the assembly. The override lever can be accessed by removing the shift lever boot. Push the lever to the left in order to override the BTSI.
Which does your S-10 have column or floor shift ? No relay ,has a solenoid .
With Column Shift A/T
The brake transmission shift interlock (BTSI) system prevents the automatic transmission from being shifted out of the PARK position unless the following conditions are present:
?€¢
The brake pedal is depressed.


?€¢
The ignition switch is turned to the RUN or the START position.

When the ignition switch is in the RUN or the START position, the current flows from the B/U Lamp fuse located in the underhood bussed electrical center (UBEC) through CKT 839 (PNK) to the park/neutral position switch. The park/neutral position switch also feeds the backup lamps portion of the switch. With the transmission in the PARK position, the current flows to the BTSI fuse located in the underhood bussed electrical center (UBEC) through CKT 275 (LT GRN). The current then flows to the TCC/stoplamp switch through CKT 584 (LT GRN/BLK). The current continues to the BTSI solenoid through CKT 1135 (DK GRN/WHT). The ground path is provided through CKT 1850 (BLK) to G207. When the brake pedal is depressed, the normally closed contacts in the TCC/stoplamp switch open and the current flow is interrupted. When the current flow is interrupted, the BTSI solenoid de-energizes. The transmission may then shift to another gear. When the transmission shifts to another gear (except PARK), the contacts in the park/neutral position switch open. This condition stops the current flow to energize the solenoid when the brake pedal releases.

Whic

Jun 09, 2016 | 1998 Chevrolet S-10 Pickup

1 Answer

Shifter is locked in park on a 2002 bravada that sayes on dash its in reverse


PRND321 Display
The instrument panel cluster (IPC) displays the selected gear position as determined by the engine control module (ECM). The IPC - instrument panel cluster receives a serial data message from the ECM indicating the gear position. The PRND321 display blanks if:
?€¢
The ECM detects a malfunction in the transmission range switch circuit.


?€¢
The IPC detects a loss of serial data communications with the ECM. The automatic transmission shift lock control system is a safety device that prevents an inadvertent shift out of PARK when the engine is running. The driver must press the brake pedal before moving the shift lever out of the PARK position. The system consists of the following components:
?€¢
The automatic transmission shift lock control solenoid


?€¢
The automatic transmission shift lock control switch

With the ignition in the ON position, voltage is supplied to automatic transmission shift lock control switch. Voltage flows through the normally closed contacts of the automatic transmission shift lock control switch to the automatic transmission shift lock control solenoid. The automatic transmission shift lock control solenoid is permanently grounded. This energizes the automatic transmission shift lock control solenoid causing the transmission shift lever to be physically locked in the PARK position. When the brake pedal is pressed the contacts in the automatic transmission shift lock control switch open, de-energizing the automatic transmission shift lock control solenoid. This allows the shift lever to be move out of the PARK position.
The transmission range (TR) switch is part of the park/neutral position (PNP) and backup lamp switch assembly, which is externally mounted on the transmission manual shaft. The TR switch contains four internal switches that indicate the transmission gear range selector lever position. The PCM supplies ignition voltage to each switch circuit. As the gear range selector lever is moved, the state of each switch may change, causing the circuit to open or close. An open circuit or switch indicates a high voltage signal. A closed circuit or switch indicates a low voltage signal. The PCM detects the selected gear range by deciphering the combination of the voltage signals. The PCM compares the actual voltage combination of the switch signals to a TR switch combination chart stored in memory.
You need a Tech2 scan tool to diagnose this problem ! possible range sensor !

Sep 03, 2015 | Cars & Trucks

1 Answer

The gear shifter on my 1998 Pontiac SE coupe will not unlock so I can take the car out of park


Do you have column or floor shifter ?
All automatic transaxle models use an electric park lock system. Within the housing assembly, a lock cylinder is connected to an actuator which rotates and engages on the electric park lock solenoid. When the floor-shift lever is not in the park position, the actuator disengages from the electric park lock solenoid slider. This allows the lock cylinder to move to the lock position. With the shift lever in PARK and the lock cylinder in LOCK, the actuator cam is positioned against the electric park lock solenoid slider. This prevents the shift lever from shifting out of the PARK position.
The column-shift automatic transaxle model uses a flexible cable actuator instead of an electric park lock system. One end of the cable is attached to the gate assembly. The other end of the cable is attached to the column mounted housing assembly. This system functions similarly to the floor-shift ignition lock system.
The manual transaxle model uses a push button lock cylinder. A clutch start switch is used. The clutch pedal must be pressed before the engine will crank. Refer to Park Lock System Check .
CAN you turn the key on ?
The gear selector does not shift out of PARK with the brake pedal depressed and the ignition switch in RUN.
Automatic Transmission Shift Lock Control Always On with Ignition in Run
Action
Value(s)
Yes
No

1

Was the BTSI System Check performed?
--
Go to Step 2
Go to Automatic Transmission Shift Lock Control System Check

2

Is this a column shift vehicle?
--
Go to Step 3 yes
Go to Step 4 no

3

  1. Move the gear selector to the PARK position.
  2. Disconnect the automatic transaxle control connector
  3. Turn the ignition switch to RUN.
  4. Connect the test lamp between terminal B and ground.
Does the test lamp light?
--
Go to Step 4
Go to Step 8

4

  1. Disconnect the brake switch connector C2.
  2. Move the ignition switch to RUN.
Can you shift the transaxle out of the PARK position?
--
Go to Step 5
Go to Step 8

5

Is the brake switch adjusted properly?
--
Go to Step 6
Go to Step 7

6

Replace the brake switch.
Is the repair complete?
--
System OK
--

7

Adjust the brake switch.
Is the repair complete?
--
System OK
--

8

  1. Disconnect the BTSI solenoid connector (column shift vehicles) or disconnect the automatic transaxle control connector (console shift vehicles).
  2. Move the ignition switch to RUN.
Can you shift the transaxle out of the PARK position?
--
Go to Step 9
Go to Step 10

9

Repair the short to power in CKT 1135.
Is the repair complete?
--
System OK
--

10

Test for sticking or binding in the shift linkage.
Does the shift linkage stick or bind?
--
Go to Step 11
Go to Step 12

11

Repair the shift linkage.
Is the repair complete?
--
System OK
--

12

Replace the BTSI solenoid (column shift vehicles) or replace the automatic transaxle control (console shift vehicles).
Is the repair complete?
--
System OK
Go to Step 1

May 18, 2015 | Pontiac Cars & Trucks

2 Answers

2005 KIA SEDONA GEAR STICK FLOPPY / BROKE?


there is a bushing for the shifter in the console that holds the stick in place. if this bushing is broken it will let the stick move freely without changing gears.

Mar 19, 2014 | 2005 Kia Sedona

1 Answer

Clucth not disengauging....


try this.you have 2 shifter cables.one is select cable the other is shift cable.first put the transmission selector lever in neutral.then move transmission shift lever to 4th gear.depress clutch to if necessary to shift.move the shift lever to the 4th gear position until contacts stop.then you turn the adjuster turn buckle so the shift cable eye aligns with the eye in the gear shift lever.when installing the cable eye. make sure the flange side of plastic bushing at the shift cable end is on the cotter pin side.the cables should be adjusted so the clearance between the shift lever and both stoppers are equal when the shift lever is moved to 3rd and 4th gear. move the shift lever to each position and check that the shifting is smooth.

Jul 12, 2009 | 1996 Mitsubishi Galant

1 Answer

How can I remove gear shift knob on a 2003 Navigator?


it looks like you disconnect the shift cable and remove the center console finish panel with the shifter.


SECTION 501-12: Instrument Panel and Console 2003 Expedition/Navigator Workshop Manual
REMOVAL AND INSTALLATION Floor Console —Front, Navigator Removal and Installation
  1. Apply the parking brake.
  1. Position the front seat forward.
  1. Remove the two front floor console rear bolts.
  1. Position the front seats rearward.
  1. Disconnect the battery. For additional information, refer to Section 414-01 .
  1. Remove the pin-typ retainer and the window control switch panel.
    • Disconnect the electrical connectors.
  1. Move the shift lever to NEUTRAL and position the shift indicator bezel aside.
  1. Remove the screws and the center console finish panel.
    • Disconnect the electrical connectors.
  1. Disconnect the shift cable.
  1. Disconnect the front floor console electrical connectors.
    1. Loosen the electrical connector bolt.
    1. Disconnect the connector.
    1. Disconnect the electrical connector.
  1. Remove the front floor console side finish panel.
    • If equipped, disconnect the electrical connector.
  1. Remove the front floor console front bolts.
  1. Remove the floor console.

Apr 17, 2009 | 2003 Lincoln Navigator

2 Answers

04 Navigator gear shift button broken


I only have 2003 Nav procedure. Maybe get used part at car-part.com. Page with * is lowest price.

SECTION 307-05: Automatic Transaxle/Transmission External Controls 2003 Expedition/Navigator Workshop Manual
REMOVAL AND INSTALLATION Selector Lever —Floor Shift Removal and Installation
  1. Lift the floor shift PRNDL bezel.
  1. Disconnect the PRNDL bezel wire harness connector.
  1. Remove the shift lever handle and cover.
    1. Slide the handle bezel down.
    1. Remove the screw.
    1. Disconnect the TCS wire harness.
    1. Lift assembly from the shifter lever.
b038436.gif
  1. Position the window regulator control panel aside.
  1. Remove the screws and the console finish panel.
  1. Remove the left side console access panel.
  1. Disconnect the transmission shift cable from the transmission selector arm.
  1. Remove the transmission shift cable retaining clip from the floor shift mechanism through the console access.
  1. Remove the four bolts retaining the floor shift mechanism to the floor.
  1. Disconnect the floor shift mechanism wire harness connector.
  1. Remove the floor shift mechanism from the console.
  1. Remove the brake shift interlock actuator, parking brake release mechanism and harness.
    • Remove the wire harness retainers.
    • Remove the wire harness retainers.
    • Remove the two screws retaining the brake shift interlock assembly.
    • Remove the two screws retaining the parking brake controller.

Mar 15, 2009 | 2004 Lincoln Navigator

2 Answers

1999 F350 crew cab 4x4 ford, gear shift lever


Ok ready to stand on your head under the dash?
It's doable... there is a flange connected to the gearshift lever under the steering column. If you remove the lower dash cover where the fuses are, you should be able to see it when you move the gear shift lever... look around on the floor of the truck to see if you dropped a star-headed bolt or two... these bolts worked loose on my superduty and made shifting very difficult..it was an easy fix... let me know how you do on it.

Dec 06, 2008 | 1999 Ford F350 Regular Cab

Not finding what you are looking for?
2003 Lincoln Aviator Logo

Related Topics:

350 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lincoln Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Fordexpert

Level 3 Expert

5331 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Are you a Lincoln Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...