Question about Daewoo Nubira

1 Answer

Where does the transmission oil and engine oil go?

Posted by on

  • sg20202003 Jan 15, 2009

    where do the transmission oil go at?

  • Joel love Aug 18, 2013

    In a plastic bottle in the boot or your garage on a shelf.

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Daewoo Master
  • 21,949 Answers

Engine oil has a filler cap on top of the engine,and the gearbox oil goes in the filler plug on the side of the gearbox when i refilled one last week after putting a clutch in one .

Posted on Jan 15, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Locate the filler plug for transmission oil


Most times transmission & engine oil are all together, NO FILLER PLUG for Transmission Oil. Automatic Engine have separate filler plug for Transmission Oil. To get at Transmission filler , car needs to be on a RAMP. It would help if you mentioned Make & Model of Car !

Feb 24, 2015 | Cars & Trucks

1 Answer

1999 dodge durango transmission has water inside


If transmission oil cooler is leaking, engine coolant may enter cooler, or transmission oil may enter engine cooling system. Both engine cooling system and transmission oil circuit should be drained, flushed, and inspected.

Sep 29, 2013 | 1999 Dodge Durango

1 Answer

How many qts of oil do i need


Depends on your engine.

1980 JEEP CJ-7 2.5L 4-cyl Engine Code [B]
CAPACITIES
Engine, GM without filter..........2.4 quarts[1]
Wix Filter ........ 51040
Cooling System, Initial Fill..........8.0 quarts
Automatic Transmission, A904, 30RH Initial Fill..........4.0 quarts[2]
Automatic Transmission, A999, 32RH Initial Fill..........4.0 quarts[2]
Automatic Transmission, Total Fill
3 speed A999, 32RH..........8.4 quarts
3 speed A904, 30RH..........7.0 quarts
Manual Transmission, 4-SPD, SR-4..........3.0 pints
Manual Transmission, 4-SPD, T176..........3.6 pints
Differential, Front..........2.5 pints[3]
Differential, Rear..........4.9 pints
Transfer Case,..........4.0 pints

1. Add extra oil when replacing filter. After refill check oil level.
2. With engine automatic transmission operating temperature, shift through all gears.
Check fluid level in NEUTRAL and add fluid as needed.
3. 1984-1992 Models with command-Track, add 5 oz of 75W-90 GL-5 to shift motor housing opening.

TORQUES
Oil Drain Plug.....25 ft-lbs
Manual Transmission T176
Fill Plug.....15 ft-lbs
Drain Plug.....15 ft-lbs
Manual Transmission SR4
Fill Plug.....20 ft-lbs

1980 JEEP CJ-7 4.2L 6-cyl Engine Code [C]
CAPACITIES
Engine, without filter..........5.0 quarts[1]
Wix Filter..... 51522
Cooling System, Initial Fill..........11.0 quarts
Automatic Transmission, A904, 30RH Initial Fill..........4.0 quarts[2]
Automatic Transmission, A999, 32RH Initial Fill..........4.0 quarts[2]
Automatic Transmission, Total Fill
3 speed A999, 32RH..........8.4 quarts
3 speed A904, 30RH..........7.0 quarts
Manual Transmission, 4-SPD, SR-4..........3.0 pints
Manual Transmission, 4-SPD, T176..........3.6 pints
Differential, Front..........2.5 pints[3]
Differential, Rear..........4.9 pints
Transfer Case,..........4.0 pints

1. Add extra oil when replacing filter. After refill check oil level.
2. With engine automatic transmission operating temperature, shift through all gears.
Check fluid level in NEUTRAL and add fluid as needed.
3. 1984-1992 Models with command-Track, add 5 oz of 75W-90 GL-5 to shift motor housing opening.

TORQUES
Oil Drain Plug.....30 ft-lbs
Manual Transmission T176
Fill Plug.....15 ft-lbs
Drain Plug.....15 ft-lbs
Manual Transmission SR4
Fill Plug.....20 ft-lbs

1980 JEEP CJ-7 5.0L 8-cyl Engine Code [H]
CAPACITIES

Engine, without filter..........4.0 quarts[1]
Wix Filter..... 51258
Cooling System, Initial Fill..........13.0 quarts
Automatic Transmission, A999, 32RH Initial Fill..........4.0 quarts[2]
Automatic Transmission, A904, 30RH Initial Fill..........4.0 quarts[2]
Automatic Transmission, Total Fill
3 speed A904, 30RH..........7.0 quarts
3 speed A999, 32RH..........8.4 quarts
Manual Transmission, 4-SPD, SR-4..........3.0 pints
Manual Transmission, 4-SPD, T176..........3.6 pints
Differential, Front..........2.5 pints[3]
Differential, Rear..........4.9 pints
Transfer Case,..........4.0 pints

1. Add extra oil when replacing filter. After refill check oil level.
2. With engine automatic transmission operating temperature, shift through all gears.
Check fluid level in NEUTRAL and add fluid as needed.
3. 1984-1992 Models with command-Track, add 5 oz of 75W-90 GL-5 to shift motor housing opening.

TORQUES
Manual Transmission T176
Fill Plug.....15 ft-lbs
Drain Plug.....15 ft-lbs
Manual Transmission SR4
Fill Plug.....20 ft-lbs

Oilman

Feb 02, 2013 | 1984 Jeep CJ7

1 Answer

Need to replace oil pan on a bmw 2004 330ci


Raise engine with special tool 00 0 200 approx. 5 mm.
- Remove suction filter housing. Remove engine splash guard.
- Drain engine oil. On vehicles with automatic transmission:
- Disconnect oil lines from automatic transmission and from oil pan.
- Release guide tube for dipstick.

Note: M52TU and M54 only.
- Detach return hose from cyclone oil separator on oil dipstick guide tube.
- Replace O-ring.
- Remove front end reinforcement.
- Detach steeling spindle from steering gear.
- Remove vane pump for power steering unit (lines remain connected).
- Disconnect plug connection to oil level sensor.
- Loosen top and unfasten bottom of left and right engine mounts.

E46 4WD only
- Remove left and right swivel bearings.
- Remove output shafts. Remove front propeller shaft.
- Remove front axle differential.
- Detach brackets for left and right control arms from engine carrier.
- Release retaining brackets for left and right stabilizer bars.
- Unfasten screw connection on front axle support and lower the front axle support.

Note: There is no need to detach the steering gear from the front axle support.

- Unfasten oil sump screws at transmission and engine ends.
- Lower and remove oil sump.
Sealing faces clean and free of seal debris.
Apply approx.3 mm wide, 2 mm high coat of Drei Bond 1209 sealing agent to the area around seams.

Installation:
  1. Replace gasket
  2. Install oil sump.
  3. Insert all oil sump screws.
  4. Insert screws in transmission end without preload at this stage.
  5. Tighten down screws in engine end.
  6. Tighten down screws in transmission end.

E60 Removing And Installing, Sealing Or Replacing Oil Sump (M54)

Necessary preliminary tasks. -
- Remove intake filter housing
- Remove guide tube for oil dipstick
- Lowering front axle support
- Drain off engine oil
- Disconnect plug connection to oil level sensor.

On vehicles with automatic transmission:
- Detach oil lines from automatic transmission and from oil pan.
- Unfasten oil pan screws at transmission and engine ends.
- Lower and remove oil pan.

Installation:
Sealing faces clean and free of seal debris.
Apply approx.3 mm wide, 2 mm high coat of Drei Bond 1209 sealing agen to the area around seams.

Installation:

  1. Replace seal.
  2. Install oil sump.
  3. Insert all screws on transmission end, without preload at this stage.
  1. Tighten down screws on engine end.
  2. Tighten screws on transmission end.

Or take it to a dealer....

Apr 19, 2011 | BMW 330 Cars & Trucks

2 Answers

How difficult is it to change the oil pan on a 1997 gmc jimmy 4x4?


4WD To Remove:
  1. Remove or disconnect the following:
    • Negative battery cable
    • Oil level indicator
    • Front differential assembly
    • Starter
    • Transmission cover
    • Oil pan drain plug and drain the engine oil into a suitable container
    • Remote oil filter pipe adapter
    • Remote oil filter hose clip bolt on oil pan
    • Starter wire harness bracket stud
    • Transmission oil cooler pipes (if equipped)
    • Access plugs for oil pan rear nuts
    • Transmission to oil pan bolts
    • Oil pan nuts and bolts gm_truck_43_ol-pn_ol-lvl-snsr.gif

      NOTE: The low oil level sensor is not reusable.
    • Remove and discard the engine oil level sensor (if applicable) gm_truck_43_ol-pn_blts.gif

    • The oil pan
    • The oil pan gasket
  2. Discard the oil pan gasket.
  3. Clean all sealing surfaces on the engine and the oil pan.
To Install:
Note: Whenever the transmission and the engine oil pan are removed from the engine at the same time install the transmission before the oil pan. This is to allow for the proper oil pan alignment. Failure to achieve the correct oil pan alignment can result in transmission failure.
  1. Apply a 0.197 inch (5 mm) wide and 1.0 inch (25 mm) long bead of adhesive GM P/N 12346141 (Canadian P/N 10953433) or equivalent to both the right and left sides of the engine front cover to engine block junction at the oil pan sealing surfaces. gm_truck_43_ol-pn_ahsv_loc_f.gif

    gm_truck_43_ol-pn_ahsv_loc_r.gif

  2. Apply a 0.197 inch (5 mm) wide and 1.0 inch (25 mm) long bead of adhesive GM P/N 12346141 (Canadian P/N 10953433) or equivalent to both the right and left sides of the crankshaft rear oil seal housing to engine block junction at the oil pan sealing surfaces. Note: Always install a new oil pan gasket. The oil pan gasket and oil pan must be installed and the fasteners tightened while the adhesive is still wet to the touch.
  3. Install the new oil pan gasket into the groove in the oil pan. Note: The oil pan alignment must always be flush or forward no more than 0.011 inch (0.3mm) from the rear face of the engine block.
  4. Install or connect the following:
    • The oil pan onto the engine block
      1. Press the oil pan gasket into the grooves of the engine front cover and crankshaft rear oil seal housing
      2. Slide the oil pan back against a suitable straight edge
    • The oil pan bolts and nuts, but do not tighten
  5. Measure the pan-to-transmission housing clearance using a feeler gage and a straight edge. gm_truck_43_ol-pn_trnz_clrc.gif

    • Use a feeler gage to check the clearance between the oil pan-to-transmission housing measurement points
      1. If the clearance exceeds 0.011 inch 0.3mm) at any of the 3 oil pan-to-transmission housing measurement points (A), then repeat the step until the oil pan-to-transmission housing clearance is within the specification
      2. The oil pan must always be forward of the rear face of the engine block
    gm_truck_43_ol-pn_trq-sqc.gif

  6. Tighten the oil pan bolts and nuts in sequence
    • Torque to: 18 ft lb (25 Nm).
  7. Measure the clearance between the 3 oil pan-to-transmission housing measurement points in order to ensure proper alignment.
  8. Install or connect the following:
    • A new oil pan drain plug seal (O-ring) onto the oil pan drain plug
    • Oil pan drain plug into the oil pan
      1. Torque to: 18 ft lb (25 Nm)
      NOTE: The low oil level sensor is not reusable.
      gm_truck_43_ol-pn_ol-lvl-snsr.gif

    • New low oil level sensor
      1. Torque to: 115 in lb (13 Nm)
    • Transmission to oil pan bolts.
      1. Torque to: 35 ft lb (47 Nm)
    • Access plugs for the oil pan rear nuts
    • Starter wire harness bracket stud
    • Transmission oil cooler pipes (if equipped)
    • Remote oil filter pipe adapter
    • Oil filter hose clip bolt to the oil pan
    • Transmission cover and bolts.
    • Starter motor
    • Front differential assembly
    • Oil level indicator
  9. Fill the engine with oil.
  10. Connect the negative battery cable.

Dec 19, 2010 | 1997 GMC Jimmy

2 Answers

How often should I change the Transmission fluid, normal driving ? Thank you Gary


It's listed in your owner's manual. Schedule A is normal driving conditions.
SCHEDULE "A"
7,500 miles (12 000km) or at 6 months
- Change engine oil.
- Replace engine oil filter.

15,000 miles (24 000km) or at 12 months
- Change engine oil.
- Replace engine oil filter.

22,500 miles (36 000km) or at 18 months
- Change engine oil.
- Replace engine oil filter.
- Inspect front wheel bearings.
- Inspect brake linings.

30,000 miles (48 000km) or at 24 months
- Change engine oil.
- Replace engine oil filter.
- Replace engine air cleaner filter.
- Replace spark plugs.
- Drain and refill automatic transmission fluid and filter (4.7L).

37,500 miles (60 000km) or at 30 months
- Change engine oil.
- Replace engine oil filter.
- Drain and refill automatic transmission fluid and filter (5.2L/5.9L).
- Drain and refill transfer case fluid.

45,000 miles (72 000km) or at 36 months
- Change engine oil.
- Replace engine oil filter.
- Inspect front wheel bearings.
- Inspect brake linings.
- Flush and replace engine coolant at 36 months, regardless of mileage.

52,500 miles (84 000km) or at 42 months
- Change engine oil.
- Replace engine oil filter.
- Flush and replace engine coolant if not done at 46 months.

60,000 miles (96 000km) or at 48 months
- Change engine oil.
- Replace engine oil filter.
- Replace engine air cleaner filter.
- Replace ignition cables (5.2L/5.9L).
- Inspect PCV valve, replace as necessary.
- Replace spark plugs.
- Inspect auto tension drive belt and replace as necessary (5.2L/5.9L).
- Drain and refill automatic transmission fluid (4.7L).

67,500 miles (108 000km) or at 54 months
- Change engine oil.
- Replace engine oil filter.
- Inspect front wheel bearings.
- Inspect brake linings.

75,000 miles (120 000km) or at 60 months
- Change engine oil.
- Replace engine oil filter.
- Drain and refill automatic transmission fluid and filter (5.2L/5.9L).
- Drain and refill transfer case.
- Flush and replace engine coolant if it has been 30,000miles (48 000km) or 24 months since last change.
- Inspect auto tension drive belt and replace if required.

82,500 miles (132 000km) or at 66 months
- Change engine oil.
- Replace engine oil filter.
- Flush and replace engine coolant if it has been 30,000miles (48 000km) or 24 months since last change.

90,000 miles (144 000km) or at 72 months
- Change engine oil.
- Replace engine oil filter.
- Replace engine air cleaner filter.
- Replace spark plugs.
- Inspect front wheel bearings.
- Inspect brake linings.
- Inspect auto tension drive belt and replace as necessary.
- Drain and refill automatic transmission fluid (4.7L).

97,500 miles (156 000km) or at 78 months
- Change engine oil.
- Replace engine oil filter.

105,000 miles (168 000km) or at 84 months
- Change engine oil.
- Replace engine oil filter.
- Flush and replace engine coolant if it has been 30,000 miles (48 000km) or 24 months since last change.
- Inspect auto tension drive belt and replace if required.

112,500 miles (181 000km) or at 90 months
- Change engine oil.
- Replace engine oil filter.
- Drain and refill automatic transmission fluid and filter (5.2L/5.9L).
- Inspect front wheel bearings.
- Inspect brake linings.
- Flush and replace engine coolant if it has been 30,000 miles (48 000km) or 24 months since last change.

120,000 miles (192 000km) or at 96 months
- Change engine oil.
- Replace engine oil filter.
- Replace engine air cleaner filter.
- Replace ignition cables (5.2L/5.9L).
- Inspect PCV valve, replace as necessary.
- Replace spark plugs.
- Inspect auto tension drive belt and replace as necessary.
- Drain and refill automatic transmission fluid (4.7L).

Thanks for using FixYa -a 4 THUMBS rating is appreciated for answering your FREE question.

Sep 05, 2010 | 2001 Dodge Durango

2 Answers

Antifreeze looks almost black in color is thisnormal.


No this is not normal, Sounds like you may be getting a little oil mixed with the water flow. I would have this checked out because you may have a crack within the engine allowing oil to mix with your coolant system.

May 10, 2010 | 2000 Toyota Camry Solara

1 Answer

Oil spec


1995 HONDA ACCORD 2.7L 6-cyl Engine Code C27A4 C27A1

Engine Oil Grade 1......API All TEMPS......5W-30
Manual Transmission,......SJ All TEMPS......10W-30, optional 10W-40
Automatic Transmission,MPZA......AF2

CAPACITIES:
Engine, with filter..........4.4 liters
Automatic Transmission, MPZA Initial Fill..........2.7 liters
Automatic Transmission, Total Fill
4 speed MPZA..........6 liters
Manual Transmission, ..........1.9 liters

1995 HONDA ACCORD 2.2L 4-cyl Engine Code F22B1 VTEC

Engine Oil Grade 1......API All TEMPS......5W-30
Manual Transmission,......SJ All TEMPS......10W-30, optional 10W-40
Automatic Transmission,A0YA......AF2

CAPACITIES:
Engine, with filter..........4.3 liters
Automatic Transmission, A0YA Initial Fill..........2.4 liters
Automatic Transmission, MP0A Initial Fill..........2.4 liters
Automatic Transmission, Total Fill
4 speed A0YA..........6 liters
4 speed MP0A..........6 liters
Manual Transmission, ..........1.9 liters

Jan 07, 2010 | 1995 Honda Accord

2 Answers

My truck is just staying in one gear.


Is your engine oil level twice as full?

Nov 19, 2009 | 2001 Honda Passport

2 Answers

After oil change car stopped driving


make sure all vacuum lines are not off and make sure all plugs to the injecters are plugged in and also make sure the plug off the transmission is still plugged in

Jan 25, 2009 | 1998 Audi A4

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

353 people viewed this question

Ask a Question

Usually answered in minutes!

Top Daewoo Experts

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

yadayada
yadayada

Level 3 Expert

60867 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Are you a Daewoo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...