Question about 1993 Saturn SL2

1 Answer

Broke my map sensor car wont stay running

My alternator blew on my 2001 pt cruiser. I dropped my ball joint,removed tie rod took out my drive axel then removed alternator. Now I re installed everything but the car starts right up runs great for 2 seconds then dies. I reinspected everything all power wires were good and all vacuum lines were on nothing out of the ordinary then I removed the dust cover off the top of my 2.4 chrysler pt cruiser engine and the map sensor was snapped off I must have hit it with my elbow removing top alternator bolt from the top. My problem is when I start the car the engine light is on then car dies after 2 or 3 seconds. The car will start right back up but stall again. The car is charging great now all other engine parts look ok. I was wondering will the car stall because of the map sensor broke off if so will the computer reset itself after I reinstall another one. I have a 1993 saturn sl2 cranks over fine ,is in proper time,good compresion, fuel to the fuel rail, wants to run when I spray startin fluid in it.
injectors have no signal no injection can a map sensor be the problem?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has answered 20 questions.

  • Expert
  • 188 Answers

It sound like the fuel pump or fule filter???? You and pull positive post off battery for a minute and put back on. this will reset computer.

Posted on Feb 14, 2009

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

Why does my 2002 pt cruiser make a popping sound from the rear passenger side when turning. Is something about to fall off?

if it only does this during turning could be a few things, possible control are bushings, tie rod/rod ends, ball joints, or axle granted the axel usually is a clicking sound not popping but has been known to pop also if its ball joints or tie rods/rod ends it take a long time and really bad wear to come apart but generally doesn't happen very often so don't worry about anything falling off just check those things listed and replace what it is soon and you will be fine

hope this helped

Aug 30, 2014 | 2002 Chrysler PT Cruiser

2 Answers

2001 pt cruiser, broken timing belt at 60mph. I replaced the belt, runs ok at higher rpm, but dies out when coming to a stop. I was told that it could be the map sensor, is this true?

his instruction is general for all vehicles. i am sorry that i do not have particularly for your 2001 chrysler PT cruiser.

first, identify the alternator.
remove the fan belt on the alternator,
label and remove all wires that is attached to it.
remove all bolts that is holding it.
remove the old alternator.

do the reverse on installing it.

Sep 11, 2012 | 2001 Chrysler PT Cruiser

1 Answer

The left front seems to be shaking when i drive,any ideas?


Mar 20, 2011 | 2001 Chrysler PT Cruiser

1 Answer

How do you remove tie-rod on 2000 mazda protege toget the cvs shafts out

Buy or borrow a tie rod end separator (like a smaller version of a ball-buster), loosen the nut, and drive the separator in to pry the shaft out. After you get the tie rod separated, you will have to loosen the retaining bolt on the end of the CV joint. Considering the age of the vehicle, you may want to just replace the tie rod ends. The job is a royal pain in the arse, and I am taking my PT Cruiser into the transmission shop tomorrow to let them do it. They quoted me 2 hours of labor for $150, although a lot of shops charge more than $75 an hour.

Jun 27, 2010 | 2000 Mazda Protege

1 Answer

I need a diagram for my 2002 pt cruiser for the ball joint and tie rod assembly...

Your best bet is to go to the auto parts store and they can show you the parts and the price of the parts as well and it costs you nothing to look.

Nov 09, 2009 | 2002 Chrysler PT Cruiser

1 Answer

Right side half side broke

disconnect outer tie rod and ball joints from wheel hub. remove hub. check for retaining bolts to trans . remove axel u will probably need to use a pry bar

Aug 14, 2009 | 2006 Chevrolet Aveo

4 Answers

How do I replace the upper ball joints in my 2002 Ford Explorer?

The upper ball joints are replaceable without replacing the control arms. Use Moog K80008 ball joints and a ball joint press.

Jun 25, 2009 | 2002 Ford Explorer

1 Answer

2001 chrysler pt cruiser map sensor

why would you worry! this is standard procedure! after hooking at back up turn key on then off and on you hear the fuel pump grunt grrr away you go! startr it up enjoy yesterday you confirmed all ways well and thanked me and another person has your situation changed??John

Jan 04, 2009 | 2001 Chrysler PT Cruiser

2 Answers

Broke my map sensor car wont stay running

Hey replace that sensor you shouldn't try to run it with out manifold air pressure is vital to eng.wan"t rid off engine light?? disconnect battery while installing your """COMPUTERIZED""" part that way when you reconnect battery just like at home PC when you install up dates you must restart your computer in order for it to recognize any up-dates such as ""MAP SENSOR""" but if you do not replace it and disconnect battery and wait a couple of means it will come rite back on!happy new year,Happy new year,John Ontario Dodge dealership tech! this made my coffee break bright !!

Jan 03, 2009 | 1998 GMC Sierra

Not finding what you are looking for?
1993 Saturn SL2 Logo

542 people viewed this question

Ask a Question

Usually answered in minutes!

Top Saturn Experts


Level 3 Expert

70387 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6879 Answers

Are you a Saturn Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides