Question about 2005 Chrysler Pacifica

1 Answer

Replace thermostat for 2005 pacifica

The one big hose that the thermostat would fit into comes off the front where the fan is. Is that the right hose?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 334 Answers

Yes thats it The two or three bolts you need to take out and then the thermostat will be right under the cover you take off then replace in reverse procedure

Posted on Jan 15, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Po455


Check all hoses and fittings from evap back to fuel tank. On 1post in pacifica world the prob was solved by dropping the fuel tank and replacing the fitting on one of the fuel pumps. Then clear the code and hopefully doesn't come back.

Sep 08, 2014 | 2005 Chrysler Pacifica

1 Answer

How does the thermostat fit properly in the housing


selectachapter.gif

Pacifica, 2003-2005
Removal & Installation

Print Here is how to do it,if it does'nt fit right make sure you have the right thermostat.


3.5L Engine


CAUTION Never remove pressure cap with the system hot and under pressure because serious burns from coolant can occur.

  1. Disconnect negative cable from remote jumper terminal.
  2. Drain cooling system.
  3. Disconnect radiator upper hose from thermostat housing.
  4. Remove thermostat housing bolts.
  5. Remove housing, thermostat, and gasket.

    0996b43f80204be2.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. View of the coolant outlet connector (1) and thermostat housing (2)-3.5L engine
    View of the coolant outlet connector (1) and thermostat housing (2)-3.5L engine

  6. Clean gasket sealing surfaces.

To install:
  1. Install thermostat and gasket into thermostat housing. For ease of installation, install bolts in housing for thermostat and gasket retention.
  2. Install thermostat and housing to the intake manifold. Tighten the bolts to 105 inch lbs. (12 Nm).
  3. Connect radiator hoses and install hose clamp.
  4. Refill cooling system.
  5. Connect negative cable to remote jumper terminal

May 02, 2012 | 2004 Chrysler Pacifica

1 Answer

Want to know how to remove and install a radiator in a chrysler pacifica 2005


Facing car right hand side lower radiator remove drain plug on cold engine. If your radiator is bad the hoses are old to cut hoses off one top one lower. Have a shop discharge AC.Remove fan connectors.Remove the front fascia (the front of the car blocking the radiator from coming out. The painted part like you got hit in the front and had to replace the front cover) Remove AC lines. Remove transmission cooler lines. Remove push pins holding top plate on radiator. Remove right and left push pin brackets.Remove AC condenser side brackets.Lift up condenser and set back down in front of radiator.Lift radiator out and remove cooler and fan Assembly.If you want the original antifreeze go to dealer or Napa Zerex G5 same thing was 15 a gallon takes 1 and a 1/4 gallons + distilled water 50/50 Sounds like a lot of fun let me know how long it takes

Dec 12, 2011 | 2005 Chrysler Pacifica

1 Answer

I have a 2005 Chrysler Pacifica. While driving I heard a faint sound almost like a pop. Then steam coming from the front drivers wheel well. Then I noticed the heater will only blow cold air. Can you...


The pop you referred to was mostly likely a radiator hose rupturing.

The steam would be indicative of a sudden, massive loss of coolant.

Do Not drive until problem is remedied.

Could also have been a radiator tank letting go, but I'd put my money on a hose.

Hoses are a LOT LESS COSTLY, and generally easier to replace.

Good luck!

Dec 30, 2010 | 2005 Chrysler Pacifica

1 Answer

It Started about 6 months ago on my 2005 chrysler Pacifica v6 3.8. my upper radiator hose colapses when i rev the engine up and it gets really hot. i can tell by the smell. i have replaced my thermostat...


REPLACE UPPER RADIATOR HOSE IT IS TOO SOFT WORN OUT CAUSE HOSE TO CLASP.I WOULD REMOVE THERMOSTAT FLUSH ENGINE BLOCK AND RADIATOR COOLANT SYSTEM NEED FLUSHING OUT.

Dec 14, 2010 | 2005 Chrysler Pacifica

1 Answer

2007 Pacifica overheated. Outside Temp only 80. Doesnt appear that front fans are working and coolant level in resevior get higher.


Turn on the AC--it should start the radiator fans immediately. If nothing, check the fuse for the fans. The relay for the fans is a solid state device that is controlled directly by engine computer. The computer reads the coolant temperature sensor which tells the computer when to turn on the fans for usual cooling. Try to turn each fan manually (engine cool) and check for bad bearings, or fan blades--both fans should spin freely without any noise. If the fans come on with AC, then replace the temperature sensor which should be located near the attachment area of the upper radiator hose on the engine. It will have a single wire attached, and look like a small brass plug with threads. Watch the engine temperature for a while after the repair as the overheating may have damaged the thermostat element. Hope this helps!

Jul 01, 2010 | 2007 Chrysler Pacifica FWD New Cars

1 Answer

How do i remove the radiator cap on 2005 pacifica


If you face the the engine bay, to the right of the engine, look down. You will see a small white plug. Reach down with your left arm; note a big oversized arm may not fit. I'm 5'10", 195 lbs and I got my arm down to the top of my upper arm. Ensure you have a pan to catch the fluid.

The challenge is locating the hole to replace the plug.

Hope this helps.

Dec 19, 2009 | 2004 Chrysler Pacifica

2 Answers

The engine is overheating. Removed the thermostat, radiator fans not kicking in, noticed collant leaking from were the water pump is located.


If the water pump is leaking, then you need to replace it, replace the thermostat as well. Make sure you have got all the air out of the cooling system, when you refill the coolant, by undoing the top hose of the radiator till water comes out, likewise with a heater hose, then start and check, when the temperature is right the fans should cut in, keep an eye on the temp guage whilst doing this.
Hope thgis helps

Nov 02, 2009 | 2004 Chrysler Pacifica

1 Answer

I need to replace the thermostat for a 2005 chrysler pacifica


Follow the Upper Radiator Hose to the Block. There is a Bell housing there that the Hose Connects to. Remove that Bellhousing and the Thermostat is Right Under it.

Jan 15, 2009 | 2005 Chrysler Pacifica

Not finding what you are looking for?
2005 Chrysler Pacifica Logo

Related Topics:

1,342 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

63291 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

chargerhp
chargerhp

Level 3 Expert

813 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...