Question about 2004 Jeep Liberty

1 Answer

Windshield washer not functioning,

Reservoir is full, fluid not coming out of fixture.

Posted by on

  • yadayada
    yadayada May 11, 2010

    when u press the wash button do u hear the pump run?

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 15,935 Answers

Is the motor humming like its trying to pump?
if not, you will need to check the washer fuse.
consult your owners manual or diagram on fusebox lid for location.
if it is ok, you will need a new pump/motor assembly.

Posted on Jan 15, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2010 subaru forester windshield washer doesn't work


take a pin and push into each of the two nipples that spray onto your windscreen .

Dec 12, 2013 | Subaru Forester Cars & Trucks

2 Answers

I have a 2004 PT Cruiser. Windshield washer reservoir is full but will not spray onto windshield.


the pump which is located on the outlet of the reservoir is either defective, corroded/loose electrical wiring on it or a blown fuse. Check the fuse first seeing it the easiest. Hope this helps

Jan 19, 2011 | 2005 Chrysler PT Cruiser

1 Answer

Washer fluid tank full, fluid coming out but trickling and not getting on windshield


Make sure the fluid is of the -20 deg. F or below type and not the 32 deg. F summer formula. It's common for summer formula to remain in the tanks of windshield wiper cleaning fluid and freeze up in the winter months.

Good luck on changing out the fluid in your reservoir.

Dec 18, 2010 | Pontiac Torrent Cars & Trucks

1 Answer

Mercury villager 1994 washer pump not working


the pump motor likely is bad. get a used washer fluid reservoir at a pick n pull yourself or at car-part.com. page with * is lowest cost.

Pump and Reservoir, Windshield Washer Removal
  1. Disconnect the battery ground cable (14301).
  2. Raise and support the vehicle.
  3. Remove the RH wheel (1007).
  4. Remove the RH front fender splash shield (16103). Refer to Section 01-02 for the removal procedure.
  5. Remove the windshield washer reservoir top bolt.

  6. Disconnect the windshield washer reservoir fluid level sensor electrical connector.
  7. Disconnect the rear window washer pump electrical connector from the rear window washer pump.
  8. Disconnect the windshield washer pump electrical connector from the windshield washer pump (17664).
  9. Place a suitable drain pan under the windshield washer reservoir (17618) and drain the washer fluid.
  10. NOTE: The rear window washer hose end is color-coded, matching the connector on the rear window washer pump. Match the colors to ensure proper installation.

    Disconnect the washer hoses from the windshield washer pump and the rear window washer pump on the windshield washer reservoir.

  11. Loosen the two windshield washer reservoir side bolts.
  12. Remove the windshield washer reservoir by sliding it out of the side slots.
  13. Remove the windshield washer pump.

    Installation
To install, reverse the removal procedure. Tighten the lug nuts (1012) to 98-118 Nm (72-87 lb-ft).

Sep 09, 2009 | 1994 Mercury Villager

2 Answers

Windshield washer not working properly


If you have used ANYTHING beside windshield solvent in you reservor, you may have created WAXING from soap in the bottom of washer tank, which clogs pump,lines, and nozzel....take the tank out and wash it..disconnect washer hoses at nozzel and clear with compressed air along with the nozzel...if you use solvent only you may have a worn washer pump or restriction...check those and good luck.....

Jul 04, 2009 | Ford Five Hundred Cars & Trucks

1 Answer

Windshield washer fluid reservoir - MB ML 350


right where the lines connect to reservoir, has little black seals that leak. I recommend removing reservoir, empty it out, then use RTV silicone and place it between seals and reservoir. Let it dry for FULL day. than reinstall.

Jun 23, 2009 | Mercedes-Benz ML350 Cars & Trucks

1 Answer

Windshield Washer Pump


IF YOU CAN HEAR THE PUMP RUNNING AND ARE NOT LEAKING FLUID THAN YOU MORE THAN LIKELY HAVE A CLOGGED LINE OR YOUR NOZZLES ARE CLOGGED. SIMPLY PULL THE HOSE FROM ONE OF YOUR NOZZLES AND SEE IF YOU ARE GETTING FLOW. IF NOT TRACE THE HOSE TO CHECK FOR BREAKS OR KINKS.

Mar 27, 2009 | 2003 Ford E250

2 Answers

Wiper fluid level sensor replacement


Reservoir —Windshield Wiper

Removal
  1. Remove the RH wheel; refer to Section 204-04 .
  1. Position RH splash shield aside.
    1. Remove six screws.
    1. Remove three pin-type retainers.
    1. Position RH splash shield aside.
  1. NOTE: Windshield washer fluid should be collected in a container after the windshield washer hoses are disconnected.
    Disconnect the electrical connector and washer hoses.
  1. Remove the upper reservoir bolt.
  1. Remove the windshield washer reservoir.
    • Loosen the two lower reservoir bolts.
------------------------------------------------------------------------------------

Jan 15, 2009 | 2000 Mercury Villager

1 Answer

Windshield washer fluid will not pump


the windshield washer pump might be bad. It should be located somewhere on the reservoir

Nov 25, 2008 | 1997 Chevrolet Suburban

Not finding what you are looking for?
2004 Jeep Liberty Logo

409 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...