Question about 2000 Mercury Villager

2 Answers

Wiper fluid level sensor replacement

Reservoir full, washer works fine, empty lite in dash is on.

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 4 Answers

Replace the entire resevoir

Posted on Mar 05, 2015

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Mercury Master
  • 4,369 Answers

Reservoir —Windshield Wiper

Removal

  1. Remove the RH wheel; refer to Section 204-04 .
  1. Position RH splash shield aside.
    1. Remove six screws.
    1. Remove three pin-type retainers.
    1. Position RH splash shield aside.
  1. NOTE: Windshield washer fluid should be collected in a container after the windshield washer hoses are disconnected.
    Disconnect the electrical connector and washer hoses.
  1. Remove the upper reservoir bolt.
  1. Remove the windshield washer reservoir.
    • Loosen the two lower reservoir bolts.
------------------------------------------------------------------------------------

Posted on Feb 25, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

7 Answers

How do I add wiper fluid to my car?


Hello. Usually when you raise your hood look to the left or over to the passenger side against the side wall there will be a blue cap covering the washer fluid tank remove it fill the the tank and snap the lid back into place.

Nov 13, 2015 | Honda CRV Cars & Trucks

1 Answer

Change out Window Washer Container in a 2005 Dodge Ram 1500 quad cab


REMOVAL
  1. Unlatch and open the hood.
  2. Disconnect and isolate the battery negative cable.
  3. Remove the fasteners securing the coolant recovery container or the coolant pressure container to the top of the cooling module and move the container aside. It is not necessary to open or drain the engine cooling system.
2008-02-02_114215_washer1.gif
  1. Disconnect the reservoir washer hose from the barbed nipple of the inline fitting at the engine compartment washer hose in the right headlamp and dash wire harness and allow the washer fluid to drain from the reservoir into a clean container for reuse.
  2. Disconnect the right headlamp and dash wire harness connector for the washer fluid level switch from the switch connector receptacle.
  3. Disconnect the right headlamp and dash wire harness connector for the washer pump/motor unit from the motor connector receptacle.
  4. Grasp the bottom of the washer reservoir firmly with both hands and pull the unit sharply upward to disengage the locking feature on the washer reservoir from the depression in the radiator shroud.
  5. Continue lifting the washer reservoir upward far enough to disengage the three mounting tabs (one at the top and two at the bottom) from the channel-like slot at the top and the two slots at the bottom of the radiator shroud.
  6. Remove the washer reservoir from the right side of the engine compartment.
INSTALLATION
  1. Position the washer reservoir into the right side of the engine compartment.
  2. Align and insert the three mounting tabs (one at the top and two at the bottom) into the two slots at the bottom and the channel-like slot at the top of the radiator shroud.
  3. Place both hands on the top of the washer reservoir and push the unit downward far enough for the locking feature on the washer reservoir to snap into the depression in the radiator shroud.
  4. Reconnect the right headlamp and dash wire harness connector for the washer pump/motor unit to the motor connector receptacle.
  5. Reconnect the right headlamp and dash wire harness connector for the washer fluid level switch to the switch connector receptacle.
  6. Reconnect the reservoir washer hose to the barbed nipple of the inline fitting at the engine compartment washer hose in the right headlamp and dash wire harness.
  7. Reposition the coolant recovery container or the coolant pressure container to the top of the cooling module and reinstall the fasteners that secure it there.
  8. Refill the washer reservoir with the washer fluid drained from the reservoir during the removal procedure.
  9. Reconnect the battery negative cable.
  10. Close and latch the hood.

Read more: http://www.justanswer.com/dodge/11zed-remove-windshield-wiper-fluid-bottle-dodge-ram-1500-2004-4.html#ixzz3P9Jywc4h

Jan 16, 2015 | Dodge Cars & Trucks

1 Answer

Audi Q5 low wiper fluid light on but reservoir full


the low washer fluid sensor might be shot. try replacing it. hope this helps.

Mar 05, 2014 | 2011 Audi Q5 2.0

2 Answers

Replaced washer fluid pump and verified power to the pump but it wont work?


first thing i would do is remove the rubber hose from the pump to the wipers. if fluid is coming out then you lines are plugged or kinked also in the past i have had to take a pin and poke the holes at the wiper end. also check inside of the washer fluid tank and see if the hose is clogged and not pulling fluid

Jan 04, 2013 | 2002 Ford Explorer

2 Answers

My wiper will work but it will not spray washer fluid anymore. Any suggestions?


CHECK WIPER FLUID LEVEL FIRST ALL IS GOOD CHECK FOR POWER AT WIPER WASHER PUMP MOTOR.IF NO POWER AT WIPER WASHER MOTOR.CHECK 15 AMP FUSE IN THE ENGINE COMPARTMENT FUSE RELAY BOX.IF YES YOU ARE GETTING POWER AT WIPER WASHER MOTOR.WIPER WASHER MOTOR FAULTY.

Dec 31, 2010 | 2004 Chevrolet Suburban

1 Answer

2006 toyota sienna wiper reservoir empty light is


they may not have plugged in the sensor or the wire is broken depending on how bad youre accident was

Feb 27, 2010 | 2006 Toyota Sienna

1 Answer

Both the front and rear washers are not working, which fuse controls this?


When you attempt to use you washers do you 1 hear a noise and no fluid or 2 if no noise no fluid, skip to 3 If 1 check your reservoir fluid level if full check nozzles for wax- polish blocking opening if clean. trace windshield hose to reservoir pull both end loose and Blow air through if clear push back on.
3 Check fuse panel if not marked wiper/washer and you do not have a manual replace all broken fuses your bound to get it that way

Jul 09, 2009 | 2005 Jeep Grand Cherokee

2 Answers

1999 grand prix wiper fluid motor?


same fuse . Could also be washer switch. Needs to be checked out with 12V test light

Mar 30, 2009 | 1999 Pontiac Grand Prix

2 Answers

Wiper fluid motor?


washer pump located in washer jar. Either washer pump is inop, or possibly a clogged water line or nozzles.

Mar 29, 2009 | 1999 Pontiac Grand Prix

Not finding what you are looking for?
2000 Mercury Villager Logo

812 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

63801 Answers

Fordexpert

Level 3 Expert

5331 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...