Question about 2002 Hyundai Santa Fe

1 Answer

Knocking noise in 3.8 lit 95 ford taurus

I just developed a rod knock or bearing knock in my engine. driving this morning and the trans. seemed as if it was in in second, not regular drive. drove on freeway about 16 miles like this. stopped car and checked it and when i put it back into drive, it was hard to shift out of first gear, had 3-4500 rpms and still wouldn't shift out of first gear. got on freeway thinking the faster i could go, the better chance it had of shifting out of first. didn't work, started knocking on the freeway and i had to creep to a service station. mechanic told me that it was a bearing and the engine was shot. then i tok it to murrays and the guy told me it sounded like a rod knock. suggested putting a heavier grade of oil along with an additive. any suggestions?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 73 Answers

You can not put a liquid where metal is supposed to be. Just a general rule of thumb. The high RPM's had been too much for the engine, and A rod bearing, or rod knocking is about the same thing. Dont try the heavier oil thing, I hate when ppl suggest such stuff. Just replace the bearing, or in most cases and cost efficent, the engine.

Posted on Jan 15, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

What's the torque on rod bearings?


Engine Noises ' Knocking and Ticking ' Common Causes

www.justautorepair.com/whats-wrong-with-my.../knocking-ticking
The following are causes of connecting rod bearing noise: ... Loose torque converter-to-flywheel or flywheel-to-crankshaft bolts will sound similar to bearing knock. .... I got a 1998 tahoe its making a lil ticking noise after I got unstuck on some ice ... 2001 FordTaurus with a loud mechanical noise that is constant when engine ...

Change 4.6L rod bearings with engine still in vehicle? 02 Explorer ...

www.ford-trucks.com > ... > Modular V8 (4.6L, 5.4L)
Aug 11, 2011 - The regular everyday rattling noises seemed to get louder than usual. ...So I dropped the pan and this is what I found: ... Is it possible to change the rod bearings with the engine still in the vehicle? ... If you decide to go with new bearings,torque your caps down on some plasti-gauge and see if you get the ... 7.3 engine r&r
Mar 22, 2012
Rod Bearing Replacement
Dec 27, 2010
More results from www.ford-trucks.com

Dec 28, 2015 | 2000 Ford Explorer

1 Answer

Car ran fine in the morning parked car and about 4 hours later i went to start and it started but there was a terible knocking and was running ruff, i tried to drive and about two blocks it stop and hasn't...


Does the engine still crank over at normal starting speed? If not, put a socket and wrench on the crankshaft pulley bolt and check that engine still turns freely. If the engine is seized, you know what that means-the terrible knocking was a main or rod bearing being bad, and seized up on the crankshaft. You would need a new engine.

If the crankshaft still turns free, be very prudent about putting money into it until you have determined the cause of the knocking. That doesn't sound good, could still be a bad crankshaft bearing.

Feb 11, 2014 | 1998 Ford Taurus

1 Answer

Makes knocking noise that sound like something is loos banging only when jeep warms up and only in gear


TROUBLESHOOTING ENGINE NOISES
A KNOCKING SOUND IN THE ENGINE IS MOST LIKELY CAUSED BY ONE OF THE FOLLOWING
1. PISTON SLAP: Makes a sharp metallic noise. Idle engine and short out each cylinder plug. The noise will disappear when plug with bad piston is shorted. Noise will also disappear at acceleration. This can be caused by worn or out of round cylinder, or broken piston ring. Correct problem by re-boring cylinder and/or replacing piston.
2. VALVE NOISE: Makes clicking or rattle noise. Caused by excessive wear on valve stem or lifter, out of adjustment, or stuck valve. Correct by adjusting valve clearance, replace worn valve or lifter, regrind cam, replace valve guide and /or valve. A stuck valve can sometimes be loosened by passing oil through the carburetor while engine is running.

3. ROD BEARING KNOCK: Makes sharp metallic noise similar to a piston slap. Detection is opposite of piston slap. Rod knock is not heard at idle. Knock becomes louder as engine speed is increased. Caused by excessive rod bearing clearance. Correct by adjusting rod bearing clearance to .0015 inches by removing shims. May require re-pouring rod bearing.
4. REAR MAIN BEARING KNOCK: Makes dull knocking or thud noise. Detected at speeds between 20 and 50 MPH. Knock will normally decrease or disappear while pulling or decelerating. Noise will be detected the loudest at normal driving speed, when not pulling or decelerating. Correct by adjusting bearing clearance to .001 to .0015 inches. If knock is excessive, crank should be checked for out of roundness. May need to re-pour all main bearings to correct.
5. TIMING GEAR KNOCK: usually the most difficult to diagnose. If gear is loose or badly worn it will knock in all ranges. Run engine slightly above idle speed. Slowly open and close throttle. Knock will continue to be present, but just as engine slows down knock will become a slight rattle. Remove timing pin and reinsert into timing hole on timing gear cover. Press timing pin tightly against timing gear and accelerate slightly above idle. Knock will significantly be reduced or disappear. Correct by replacing both timing gear and crank gear as a matched set. The two gears should have a backlash clearance of .003 to .004. If more than .009 inch backlash, an oversize (.005) timing gear should be installed.
6. WRIST PIN SLAP: This can not be detected by shorting out the cylinder plugs. Rapidly accelerate and decelerate the engine speed. The engine will pass through a certain speed range when the wrist pin will rattle at about the same pitch as a valve tappet noise. This can be corrected by installing a new wrist pin bushing in the rod or new wrist pin f badly worn. Wrist pin should fit the piston and connecting rod with a tight metal to metal fit. The pin can be pushed into the piston and rod with a slight pressure of the hand. Pin to rod clearance is .0003 to .0005 inches.

Dec 07, 2013 | Jeep Cars & Trucks

1 Answer

Making knocking sound


A KNOCKING SOUND IN THE ENGINE IS MOST LIKELY CAUSED BY ONE OF THE FOLLOWING
1. PISTON SLAP: Makes a sharp metallic noise. Idle engine and short out each cylinder plug. The noise will disappear when plug with bad piston is shorted. Noise will also disappear at acceleration. This can be caused by worn or out of round cylinder, or broken piston ring. Correct problem by re-boring cylinder and/or replacing piston.
2. VALVE NOISE: Makes clicking or rattle noise. Caused by excessive wear on valve stem or lifter, out of adjustment, or stuck valve. Correct by adjusting valve clearance, replace worn valve or lifter, regrind cam, replace valve guide and /or valve. A stuck valve can sometimes be loosened by passing oil through the carburetor while engine is running.

3. ROD BEARING KNOCK: Makes sharp metallic noise similar to a piston slap. Detection is opposite of piston slap. Rod knock is not heard at idle. Knock becomes louder as engine speed is increased. Caused by excessive rod bearing clearance. Correct by adjusting rod bearing clearance to .0015 inches by removing shims. May require re-pouring rod bearing.
4. REAR MAIN BEARING KNOCK: Makes dull knocking or thud noise. Detected at speeds between 20 and 50 MPH. Knock will normally decrease or disappear while pulling or decelerating. Noise will be detected the loudest at normal driving speed, when not pulling or decelerating. Correct by adjusting bearing clearance to .001 to .0015 inches. If knock is excessive, crank should be checked for out of roundness. May need to re-pour all main bearings to correct.
5. TIMING GEAR KNOCK: usually the most difficult to diagnose. If gear is loose or badly worn it will knock in all ranges. Run engine slightly above idle speed. Slowly open and close throttle. Knock will continue to be present, but just as engine slows down knock will become a slight rattle. Remove timing pin and reinsert into timing hole on timing gear cover. Press timing pin tightly against timing gear and accelerate slightly above idle. Knock will significantly be reduced or disappear. Correct by replacing both timing gear and crank gear as a matched set. The two gears should have a backlash clearance of .003 to .004. If more than .009 inch backlash, an oversize (.005) timing gear should be installed.
6. WRIST PIN SLAP: This can not be detected by shorting out the cylinder plugs. Rapidly accelerate and decelerate the engine speed. The engine will pass through a certain speed range when the wrist pin will rattle at about the same pitch as a valve tappet noise. This can be corrected by installing a new wrist pin bushing in the rod or new wrist pin f badly worn. Wrist pin should fit the piston and connecting rod with a tight metal to metal fit. The pin can be pushed into the piston and rod with a slight pressure of the hand. Pin to rod clearance is .0003 to .0005 inches.

Dec 06, 2013 | Nissan Cars & Trucks

1 Answer

V6 knocking noise


A KNOCKING SOUND IN THE ENGINE IS MOST LIKELY CAUSED BY ONE OF THE FOLLOWING
1. PISTON SLAP: Makes a sharp metallic noise. Idle engine and short out each cylinder plug. The noise will disappear when plug with bad piston is shorted. Noise will also disappear at acceleration. This can be caused by worn or out of round cylinder, or broken piston ring. Correct problem by re-boring cylinder and/or replacing piston.
2. VALVE NOISE: Makes clicking or rattle noise. Caused by excessive wear on valve stem or lifter, out of adjustment, or stuck valve. Correct by adjusting valve clearance, replace worn valve or lifter, regrind cam, replace valve guide and /or valve. A stuck valve can sometimes be loosened by passing oil through the carburetor while engine is running.

3. ROD BEARING KNOCK: Makes sharp metallic noise similar to a piston slap. Detection is opposite of piston slap. Rod knock is not heard at idle. Knock becomes louder as engine speed is increased. Caused by excessive rod bearing clearance. Correct by adjusting rod bearing clearance to .0015 inches by removing shims. May require re-pouring rod bearing.
4. REAR MAIN BEARING KNOCK: Makes dull knocking or thud noise. Detected at speeds between 20 and 50 MPH. Knock will normally decrease or disappear while pulling or decelerating. Noise will be detected the loudest at normal driving speed, when not pulling or decelerating. Correct by adjusting bearing clearance to .001 to .0015 inches. If knock is excessive, crank should be checked for out of roundness. May need to re-pour all main bearings to correct.
5. TIMING GEAR KNOCK: usually the most difficult to diagnose. If gear is loose or badly worn it will knock in all ranges. Run engine slightly above idle speed. Slowly open and close throttle. Knock will continue to be present, but just as engine slows down knock will become a slight rattle. Remove timing pin and reinsert into timing hole on timing gear cover. Press timing pin tightly against timing gear and accelerate slightly above idle. Knock will significantly be reduced or disappear. Correct by replacing both timing gear and crank gear as a matched set. The two gears should have a backlash clearance of .003 to .004. If more than .009 inch backlash, an oversize (.005) timing gear should be installed.
6. WRIST PIN SLAP: This can not be detected by shorting out the cylinder plugs. Rapidly accelerate and decelerate the engine speed. The engine will pass through a certain speed range when the wrist pin will rattle at about the same pitch as a valve tappet noise. This can be corrected by installing a new wrist pin bushing in the rod or new wrist pin f badly worn. Wrist pin should fit the piston and connecting rod with a tight metal to metal fit. The pin can be pushed into the piston and rod with a slight pressure of the hand. Pin to rod clearance is .0003 to .0005 inches.

Dec 06, 2013 | Cars & Trucks

1 Answer

Knocking in 1999 Ford Taurus


is it a constant knock or is when you turn?

Dec 23, 2011 | 1999 Ford Taurus

1 Answer

I heard a knocking the other day and now it died! Here is what some people have said the noise was....fly wheel on transmission, rod knocking. I have checked all fluids and they are fine. Any ideas?


Fly wheel will not cause a knock. Knocking may be caused by insufficient oil supply within the engine. This may be caused by a failed oil pump, excessive sludge build-up, faulty rod or main bearings. Did you notice the oil light for flickering or being lit while driving?? Is the engine able to spin when you are starting it??

Oct 26, 2010 | 2002 Jeep Liberty

2 Answers

Knocking in motor. Not valves


Sounds like you have a rod knock. Excessive bearing clearance happens and creates the knock. Time to rebuild the engine or get another one.

Aug 19, 2008 | Ford Bronco Cars & Trucks

1 Answer

1986 FORD 300 SIX CYLINDER ENGINE KNOCKS


Hi Bill 609!

Definitely sound like a rod insert to me. With my practiced ear, I cna tell the difference between a main bearing knock (deeper sound, more of a thudding noise), rod bearing knock (not so deep, gets louder as the engine revs, kind of a rat-tat-tat-tapping noise), and a wrist-pin knock (not quite as loud or deep and gets louder with decelerating RPM).

You can tell which cylinder the knock is on by removing the spark wires to each cylinder one at a time while the engine is still cold enough to knock. (Don't get shocked!)... when you hit the right one, the knock will noticeably quieten or possibly quit altogether!

The 300 Six is a tough old motor and I have seen them survive for years with rod knocks... Just allow the engine ample warm-up time before driving, drive on the conservative side, and keep an eye on oil level and pressure.

An oil and filter change to a higher viscosity oil with a can of STP Oil Treatment (Or something similar) is a good band-aid fix for now, I would recommend Castrol GTX 20/50w... in my opinion, Castrol is the best brand out there, I use it religiously - - - I have a customer with a Chevy Suburban who has followed my advice and adhered to good maintenance discipline that has racked up over 300,000 miles on the original small block and no consumption or engine issues, and is still running strong!

Bill, the temporary fix will work for a while, hopefully a long while --- BUT when it reaches the point that the knock doesn't go away, it is time to park it until the real repair can be done --- otherwise you risk throwing a rod and destroying your engine beyond repair!!!

Please don't hesitate to post a comment or ask if you have further questions. I hope this information answers your question and concerns and wish you well with the Ford. *** And remember to rate my assistance... Your rating is my only compensation for helping you in the free blog!!!***

Thanks!
-WildBill

Jun 27, 2008 | 2007 Ford F-150 Harley Davidson

Not finding what you are looking for?
2002 Hyundai Santa Fe Logo

567 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

70387 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6880 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...