Question about 1991 Chevrolet Lumina

1 Answer

Install lmnina battery

How do I install the battery

Posted by on

  • yadayada
    yadayada May 11, 2010

    lease explain what problem u are having with the battery installation.

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

You have to take the brace off then the windshield fulid tank off and the air filter too...

Posted on Feb 04, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change a battery in a Saturn ion 2003?


1. Open the trunk

2. Lift the carpet/flooring of the trunk to reveal the battery.

3. Disconnect the negative battery cable (8mm)

4. Disconnect the positive battery cable (8mm).

5. Remove the battery hold down block (13mm).

6. Remove the battery vent tubes from the top of the battery.

7. Lift the battery out of the trunk.

8. Install the new battery in the trunk.

9. Install the hold down block.

10. Install the battery vent tubes.

11. Install the positive cable.

12. Install the negative cable.

13. Lay the flooring/carpet back down where it fits correctly.

14. Close the trunk.

Feb 25, 2015 | Saturn Ion Cars & Trucks

1 Answer

Can a new car radio kill the battery?


Yes and that was due to bad installation. I have had 3 car stereos installed on my 98 RAV4 through Best Buy and never had battery problems. I even had 2 amps installed as well but the installers had to make me buy this 200-dollar thing that would not drain the battery.

If you are getting a drain through the radio's power supply it could eventually drain down the battery if it was improperly installed, I would pull the fuse for the radio and see if the drain continues, if the drain does not stop there is another short somewhere. To learn more :

http://www.xcardiag.com/wholesale/automotive-battery-analyser-vat-560-tool-536.html

May 16, 2012 | Cars & Trucks

1 Answer

Replacing battery on Aston Martin Vanquish


Below is the procedure for an Aston Martin Vantage, perhaps the vanquish is similar?

Removal
1. Power the driver's fully forward.
2. Remove rear compartment cover.
3. Loosen and disconnect battery terminals, earth (- ve)
terminal first.
4. Release rear carpet, studs (x2), move carpet aside.
5. Remove screws (x2), battery compartment cover to
support rail.
6. Remove nuts (x2), battery compartment cover to body.
Remove cover.
7. Remove Torx screws (x4), remove battery clamps (x2).
8. Disconnect battery vent tube.
9. With assistance, remove battery.
Installation
1. Clean battery tray and clamps.
2. With assistance, install battery into its compartment.
3. Connect battery vent tube.
4. Position battery clamps (x2), install and torque tighten
Torx screws (x4).
5. Ensure battery vent tube is not distorted by battery.
6. Install battery terminals, tighten terminal nuts to correct
torque.
7. Install battery compartment cover, install and tighten
screws (x2) and nuts (x2).
8. Position rear carpet, secure with studs.
9. Install rear compartment cover.
10. Reposition driver's seat.
Courtesy of pistonheads.com

Please vote if this helps! Thanks, Mike

Jun 12, 2011 | Aston Martin Vanquish Cars & Trucks

1 Answer

Trying to remove the battery from my 2007 soltice


Hello robert.... Battery Replacement

Removal Procedure

Disconnect the negative battery cable (2). Refer to Battery Negative Cable Disconnect/Connect Procedure .

Remove the wheelhouse liner. Refer to Wheelhouse Liner Replacement - Front .

Lower the vehicle.

Open the positive battery cable connection cover.

Loosen the positive battery cable bolt.

Remove the positive battery cable (1).

Remove the front fender rear bracket to side rail bolts.

Remove the front fender to front fender rear bracket upper (1) and lower (2) bolts.

Remove the front fender rear bracket.

Remove the battery hold down retainer bolt and retainer.

Important: Do not tip the battery more than 40 degrees during removal.

Remove the battery.



Installation Procedure

Important: Do not tip the battery more than 40 degrees during battery installation.

Install the battery.
Notice: Refer to Fastener Notice in Cautions and Notices.

Install the battery hold down retainer and bolt. Tighten the bolt to 25 N·m (18 lb ft).

Install the front fender rear bracket.

Install the front fender rear bracket to side rail bolts. Tighten the bolts to 20 N·m (15 lb ft).

Install the front fender to front fender rear bracket upper (1) and lower (2) bolts. Tighten the bolts to 20 N·m (15 lb ft).

Install the positive battery cable (1).

Tighten the positive battery cable bolt. Tighten the bolt to 17 N·m (13 lb ft).

Close the positive battery cable connection cover.

Install the wheelhouse liner. Refer to Wheelhouse Liner Replacement - Front .

Connect the negative battery cable (2). Refer to Battery Negative Cable Disconnect/Connect Procedure .


Joe
Thanks for choosing Fixya!

Jan 30, 2011 | 2007 Pontiac Solstice Convertible

1 Answer

Where is the battery located?


Battery Replacement

Removal Procedure

Disconnect the negative battery cable (2). Refer to Battery Negative Cable Disconnect/Connect Procedure .

Remove the wheelhouse liner. Refer to Wheelhouse Liner Replacement - Front .

Lower the vehicle.

Open the positive battery cable connection cover.

Loosen the positive battery cable bolt.

Remove the positive battery cable (1).

Remove the front fender rear bracket to side rail bolts.

Remove the front fender to front fender rear bracket upper (1) and lower (2) bolts.

Remove the front fender rear bracket.

Remove the battery hold down retainer bolt and retainer.

Important: Do not tip the battery more than 40 degrees during removal.

Remove the battery.



Installation Procedure

Important: Do not tip the battery more than 40 degrees during battery installation.

Install the battery.
Notice: Refer to Fastener Notice in Cautions and Notices.

Install the battery hold down retainer and bolt. Tighten the bolt to 25 N·m (18 lb ft).

Install the front fender rear bracket.

Install the front fender rear bracket to side rail bolts. Tighten the bolts to 20 N·m (15 lb ft).

Install the front fender to front fender rear bracket upper (1) and lower (2) bolts. Tighten the bolts to 20 N·m (15 lb ft).

Install the positive battery cable (1).

Tighten the positive battery cable bolt. Tighten the bolt to 17 N·m (13 lb ft).

Close the positive battery cable connection cover.

Install the wheelhouse liner. Refer to Wheelhouse Liner Replacement - Front .

Connect the negative battery cable (2). Refer to Battery Negative Cable Disconnect/Connect Procedure . 1737d1122299169-solstice-service-battery-replacement-procedures-158wilmingtoncarshow36.jpg
hope this helps . please rate my response.

Nov 28, 2010 | 2007 Pontiac Solstice Convertible

1 Answer

How to change battery


  1. Disconnect the battery ground (negative) cable from the battery. Refer to Battery Negative Cable Disconnection and Connection .
  2. Remove the RH fender diagonal brace. Refer to Front Fender Upper Diagonal Brace Replacement in Body Front End.
    513051.gif
    tif.gif
  3. Disconnect the battery positive cable terminal bolt from the battery.
    513047.gif
    tif.gif
  4. Remove the battery hold down retainer bolt (1).
  5. Remove the battery hold down retainer (2). Important: Do not tip the battery more than 40 degrees during removal.
  6. Remove the battery (3).
    201375.gif
    tif.gif
  7. Remove the battery insulator from the battery.
Installation Procedure

    201375.gif
    tif.gif
  1. Install the battery insulator to the battery.
    513047.gif
    tif.gif
    Important: Do not tip the battery more than 40 degrees during removal.
  2. Install the battery (3) to the battery tray.
  3. Install the battery hold down retainer (2). Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.
  4. Install the battery hold down retainer bolt (1). Tighten
    Tighten the battery hold down bolt to 18 N·m (13 lb ft).

    513051.gif
    tif.gif
  5. Connect the battery positive cable to the battery. Tighten
    Tighten the battery positive terminal bolt to 15 N·m (11 lb ft).
  6. Install the RH fender diagonal brace. Refer to Front Fender Upper Diagonal Brace Replacement in Body Front End.
  7. Connect the battery negative cable to the battery. Tighten
    Tighten the battery negative terminal bolt to 15 N·m (11 lb ft).

Nov 11, 2010 | 2000 Chevrolet Monte Carlo

1 Answer

I need to replace the driver's side brake light.


Rear Combination Light- 2007 might vary from these diagrams:
Removal & Installation 2004 (Early Production) 4 Door To Remove:
  1. Disconnect battery negative cable.
  2. Disconnect electrical connector. Rear Combination Light kia-06-18-7495.gif

  3. Remove 2 screws and 2 nuts and remove light assembly.
To Install:
  1. Install light assembly and 2 screws and 2 nuts.
  2. Connect electrical connector.
  3. Connect battery negative cable.
5 Door To Remove:
  1. Disconnect battery negative cable.
  2. Disconnect electrical connector. Rear combination light kia-06-18-7496.gif

  3. Remove 2 screws and push light assembly toward outside of vehicle. CAUTION
    Use care to not damage gasket.
  4. Pull rear combination light from vehicle.
To Install:
  1. Install rear combination light and 2 screws.
  2. Install 2 screws.
  3. Connect electrical connector.
  4. Connect battery negative cable.
2004 (Late Production), 2005-2009 To Remove:
Turn Signal Lamp kia-06-20-7698.gif

  1. Disconnect battery negative cable.
  2. Remove 2 screws and cover inside trunk.
  3. Remove 4 nuts and disconnect electrical connector (A).
  4. Remove rear combination lamp.
To Install:
Turn Signal Lamp kia-06-20-7698.gif

  1. Install rear combination lamp.
  2. Install 4 nuts and connect electrical connector (A).
  3. Install cover inside trunk and install 2 screws.
  4. Connect battery negative cable.
prev.gif next.gif

Oct 28, 2010 | 2007 Kia Spectra5

1 Answer

How do you remove a 1999 Nissan Altima starter?


Nissan Car Altima & Sentra 1999-06 StarterRemoval & Installation
  1. Remove or disconnect the following:
    Negative battery cable Air duct Harness protector from the harness Starter wiring at the starter Starter-to-engine bolts Starter from the vehicle


  2. b53bb6c.jpg
    Fig. Starter location and mounting detail-3.0L Maxima with a manual transaxle


    b2eb267.jpg
    Fig. Starter location and mounting detail-3.5L Maxima

To install:
  1. Install or connect the following:
    Starter and torque the long bolt to 57-72 ft. lbs. (77-98 Nm) on Altima and Maxima and 41 ft. lbs. (55 Nm) on 350 Z. torque the short bolt to 22-30 ft. lbs. (30-41 Nm) Starter wiring Harness protector Air duct Negative battery cable
  1. Remove or disconnect the following:
    Negative battery cable Air inlet tube Harness bracket Wiring at the starter Starter

To install:
  1. Install or connect the following:
    Starter and torque the bolts to 60 inch lbs. (7 Nm) Starter electrical connectors Harness bracket Air inlet tube Negative battery cable

1.6L & 2.0L Engines
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Remove or disconnect the following:
    Negative battery cable Wiring at the starter Bolts attaching the starter to the engine Starter
To install:
  1. Install or connect the following:
    Starter and torque the bolts to 70 inch lbs. (8 Nm) Starter electrical connections Negaative battery cable

1.6L, 1.8L & 2.0L Engines
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:
    Negative battery cable Wiring at the starter Bolts attaching the starter to the engine Starter
To install:
  1. Install or connect the following:
    Starter and torque the bolts to 70 inch lbs. (8 Nm) Starter electrical connections Negative battery cable

1.8L & 2.0L Engines
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:
    Negative battery cable Wiring at the starter Bolts attaching the starter to the engine Starter
To install:
  1. Install or connect the following:
    Starter and torque the bolts to 70 inch lbs. (8 Nm) Starter electrical connections Negative battery cable

2.4L & 2.5L Engines
  1. Remove or disconnect the following:
    Negative battery cable Air inlet tube Harness bracket Wiring at the starter Starter
To install:
  1. Install or connect the following:
    Starter and torque the bolts to 60 inch lbs. (7 Nm) Starter electrical connectors Harness bracket Air inlet tube Negative battery cable

2.4L Engine
  1. Remove or disconnect the following:
    Negative battery cable Air inlet tube Harness bracket Wiring at the starter Starter
To install:
  1. Install or connect the following:
    Starter and torque the bolts to 60 inch lbs. (7 Nm) Starter electrical connectors Harness bracket Air inlet tube Negative battery cable

2.5L Engine
  1. Remove or disconnect the following:
    Negative battery cable Air cleaner cover and duct Harness bracket Wiring at the starter Starter
To install:
  1. Install or connect the following:
    Starter and torque the bolts to 60 inch lbs. (7 Nm) Starter electrical connectors Harness bracket Air inlet tube Negative battery cable

3.5L Engines
  1. Remove or disconnect the following:
    Negative battery cable Air cleaner case (upper) and air cleaner to electric throttle control actuator tube. Harness protector from the harness Starter wiring at the starter Starter-to-engine bolts Starter from the vehicle

    42c548c.jpg
    Fig. Starter location and mounting detail-3.5L engine

continue...

Apr 05, 2010 | 1999 Nissan Altima

2 Answers

Dead battery


Removal Procedure

Disconnect the negative battery cable

Remove the wheelhouse liner.

Open the positive battery cable connection cover.

Loosen the positive battery cable bolt.

Remove the positive battery cable

Remove the front fender rear bracket to side rail bolts.

Remove the front fender to front fender rear bracket upper (1) and lower (2) bolts.

Remove the front fender rear bracket.

Remove the battery hold down retainer bolt and retainer.

Important: Do not tip the battery more than 40 degrees during removal.

Remove the battery.



Installation Procedure

Important: Do not tip the battery more than 40 degrees during battery installation.

Install the battery.


Install the battery hold down retainer and bolt.

Install the front fender rear bracket.

Install the front fender rear bracket to side rail bolts.

Install the front fender to front fender rear bracket upper (1) and lower (2) bolts.

Install the positive battery cable (1).

Tighten the positive battery cable bolt.

Close the positive battery cable connection cover.

Install the wheelhouse liner.

Connect the negative battery cable

Oct 15, 2009 | 2006 Pontiac Solstice

2 Answers

WHAT IS THE TRICK TO REPLACING A BATTERY ON A 1992 LUMINA


0900823d8004fd1f.jpg


  • Loosen the battery negative terminal clamp.

0900823d8004fd20.jpg


  • Use a terminal clamp puller to remove the negative cable.

0900823d8004fd21.jpg


  • Loosen the battery positive terminal clamp.

0900823d8004fd22.jpg


  • Use a terminal clamp puller to remove the positive clamp.

0900823d8004feae.jpg


  • Remove the battery hold-down hardware and any heat shields.

0900823d8004feaf.jpg


  • Remove the battery from the tray.

0900823d8004a233.jpg


  • Install the new battery into the tray.
  • Also install the hold-down hardware.

0900823d8004fd23.jpg


  • Install the positive battery cable.
  • Then install the negative cable.
  • When installing a battery, be careful to observe the correct polarity. Reversing the cables destroys the diodes. Proper polarity must also be observed when connecting a booster battery, positive to positive and negative to ground.

0900823d8004feb2.jpg

Art courtesy of Delmar - Thomson Learning.
  • Coat the terminals with corrosion preventative spray, then check the job by starting the car.

Jan 09, 2009 | 1992 Chevrolet Lumina

Not finding what you are looking for?
1991 Chevrolet Lumina Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

61037 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...