Question about 2001 Nissan Altima

2 Answers

Replacing the oil pan on a 2000 altima

I was just curious to know if when replacing the oil pan on my altima if i had to put a certain amount of torque into the bolts and if so how many pounds?

Posted by on

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 404 Answers

Never do them really tight as you could pinch the gasket just firm enough to crush the gasket enough to seal.

Posted on Jan 15, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 716 Answers

No You Just Want Them To Be Even And Not Over Tightened.
Happy Fixing.

Posted on Jan 15, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Ok I have a 1995 ford aspire im trying to figure out how to replace the oil pump


Disconnect the motor mounts and jack the engine to remove the oil pan. Remove the oil pan, replace the oil pump you'll find at the end of a pick up tube, replace the pump and put the pick up tube back on the new pump making sure it's in the same low position it was when removed, replace the oil pan gasket and put the oil pan back on, lower the engine and put the motor mount bolts back in. Put in the proper amount of oil and go.

Nov 13, 2014 | 1995 Ford Aspire

1 Answer

2000 Mitsubishi Galant Oil Light.


if your oil pan is smushed up to far it will slow oil flow and damage engine

May 05, 2012 | 2000 Mitsubishi Galant

3 Answers

Where is the oil pan drain plug on a 2000 toyota camry


it should be off to the side by the cv shaft, i think its facing the passanger side.gotta remove the plastic covers! if applicable

Dec 22, 2011 | 2000 Toyota Camry

1 Answer

My 97dodge intrepid is leaking oil and i want to know where is the oil pan?


Hi. You might need to Replace the oil pan gasket is the oil is leaking. Here's the procedure on how to Replace the oil pan gasket.

1. Jack up the front end of the car and slide a jack stand under the vehicle. Make sure the jack stand is securely in place, and then put blocks in front of the rear wheels to keep them from rolling.

2. Slide under the car and put a drain pan under the drain plug of the oil pan. Loosen the drain plug with a socket wrench and allow all of the old oil to drain into the pan. Remove the old oil filter.

3. Disconnect the negative battery cable and remove the dipstick and its housing. Remove the collar on the rear of the oil pan. If the vehicle is equipped with engine oil cooler lines that lead to the oil pan, remove them as well, along with transmission oil cooler clips.

4. Remove the bolts holding the oil pan, and carefully remove the oil pan. Remove the old gasket. Scrape it with a putty knife if necessary, but be very careful not to scratch the surface.

5. Wipe out the oil pan with a clean cloth or paper towel, and wipe the joining surface of the oil pan with cleaning fluid or solvent. Apply a thin bead of automotive sealer and install the new gasket.

6. Replace the oil pan, tightening the bolts securely. Replace the transmission oil cooler clips, engine oil cooler lines, oil pan collar, dipstick housing and dipstick, and reconnect the negative battery cable. Install a new oil filter.

7. Take the car off the jack stand and fill the engine with the appropriate amount of SAE 10W-30 or SAE 5W-30.

All the best!

Nov 09, 2010 | 1997 Dodge Intrepid

1 Answer

Change the oil on a 2000 Dodge Caravan


Jack up pass side.Put cardboard, BIG piece under engine just in case. Using a pan to drain the oil in put under oil pan drain plug. Remove drain plug with socket wrench. Let drain 5 min. Check the gasket on the drain plug, if bad replace with new gasket .99 cents to replace gasket only on plug. Put plug back in DO NOT OVER TIGHTEN the plug. Slide drain pan with drained oil to the front to remove oil filter. Using a filter wrench remove oil filter. Let drain. When installing new filter put a little new engine oil on the rubber gasket on the filter with your finger. Screw filter back on tighten with filter wrench. Fill van with oil from front valve cover opening.

Nov 21, 2009 | 2000 Dodge Caravan

1 Answer

Nissan Altima 2000 - Engine oil leaking problem.


replace the front oil seal. first i would clean the engine with purple power (degrease etc.) then look at the engine and make sure the leak is not coming from above like possibly the valve cover gasket or from the oil sending unit. try to tighten the bolts on the valve cover and even the oil pan. you never know, you may get lucky. i don't know where you are but front seals are cheap but the labor on the job is what costs you.

Jun 16, 2009 | 2000 Nissan Altima

2 Answers

I just had the head and radiator fixed on my 01 altima but now theres no oil pressure do anybody know why?


Check oil pump, that is probably not working. If the oil pump is fine you have a big oil leak.

May 15, 2009 | 1998 Nissan Altima

1 Answer

Where is the PCV valve on a 2000 nissan altima se?


the pvc valve is right on top of the valve cover if you do not know what the valve cover is it is were you put the engine oil into the car. there are 2 covers on has the deal to add the engine oil and the other one looks just like it with out the cap for the engine oil

Apr 21, 2009 | 2000 Nissan Altima

Not finding what you are looking for?
2001 Nissan Altima Logo

248 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

63291 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...