Question about 1992 Honda Civic

1 Answer

Ack up lights dont work when put in reverse

What can the problem be on a chevy s10 1998 when u put it in reverse no back up lights

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Welcome Back:

    Visited the website for 2 consecutive days.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 8 Answers

If all fuses are intact and someone did not fiddle with the wiring or plugged out the back up switch, then its most probably the back up switch. Its fitted on the gearbox.

Posted on Jan 15, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why does my 95 chevy 4x4 diesel keep blowing fuses when i put it in reverse


You can rule out internal transmission wires. The only thing I know of would be the reverse light wiring. You have one power wire to the neutral switch. So when the lights are supposed to come on the fuse blows the turn signal . You said you check the wiring, Did you check for continuity? High resistance cause a higher amperage draw. Also did you check the hot wire for short to ground? Try leaving the engine off. No lights on. Put it in reverse, see what lights come on. Have someone stand in back and watch as you put it in reverse. The lights should flash for a split second before the fuse blows. If any other lights come on, you have lost ground to the reverse lights.


25349764-hyer52qe2lvlylkatonhnc1i-2-2.gif

Jan 01, 2015 | Cars & Trucks

1 Answer

1997 Chevy Lumina REAR BRAKE LIGHTS DONT WORK


This will either be a fuse or the brake light switch which is on the pedal it's self. More likely the switch as these are fickle at best.

Nov 22, 2011 | 1997 Chevrolet Lumina

2 Answers

When I put my truck in reverse the reverse lights dont work


There is a reverse light switch in your gearshift on some cars/trucks that can go bad..
I would check the light bulbs, then the wiring back to your reverse lights, check to see if you have a fuse that could of blown for your model truck, then think about replacing your reverse switch.

Mar 24, 2011 | Chevrolet 1500 Cars & Trucks

2 Answers

How do i start my toyota camry after i have hit the kill switch?


I guess you tried reversing the kill switch. But did you try it after you put the ignition on? Some switches work this way. Try different things. ignition on, ignition off, etc

Apr 28, 2010 | 2000 Toyota Camry

2 Answers

Reverse and interior lights out, chevy express van


Fuse block under the hood. Driver's side, under the brake master cylinder. Number 18. TCB#2. Replace the fuse.

There is an under-engineered ground in the reverse circuit. If you back up with the dome lights on, it could blow that fuse. There should be some extra fuses under the cover of the fuse block.

Apr 25, 2010 | 2007 Chevrolet Express Passenger

3 Answers

My reverse lights dont work put new bulbs in but still dont work


you might have a reverse switch fault check on the box to see if it is connecting to the gear leaver when you put it in reverse..if not then that will have to be replaced, it might be the plunger in the switch broken or worn away..hope this helps

Feb 16, 2010 | 2004 Mazda 6

2 Answers

I have a 98 jeep cherokee 4L 4x4 automatic and the reverse lights dont work the bulbs are good and all fuses are too? any ideas


Reverse lamp switch wiring or switch itself is defective. Mounted on trans. Run slector lever over reverse with someone watching. the back.If yhey flicker the switch is bad. Work it several times sometimes helps .

Oct 28, 2009 | 1998 Jeep Cherokee

1 Answer

How to fix reverse lights on a 88 chevy truck


not a plug , though kinda looks like one , but a neutral safety switch at the transmission (follow the wire to side of trans case)

Dec 04, 2008 | 1988 Chevrolet K1500

4 Answers

1998 Chevy S10 pickup backup lights don't work


Yes it screws in on right side of tramission and you will need a 7/8 inch deep socket to remove it. You may be able to clean the old one once it is removed. There is a little ball thatgets dirty and may you can get by with cleaning it. Good Luck. Ed

Sep 06, 2008 | 1991 Chevrolet S-10 Blazer

Not finding what you are looking for?
1992 Honda Civic Logo

433 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...