Question about 2006 Chevrolet Cavalier

1 Answer

96 CHEVY CAVALIER. R&R DRIVE AXLE SHAFTS. AUTO TRANS.

HOW TO R&R THE DRIVE AXLE SHAFTS ON A 96 CHEVY CAVALIER WITH AUTO.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 73 Answers

If your looking to replace them, wich is what most do today, it is cheaper to purchase a axle with new cv joints than to rebuild them. It is a very simple job in todays cars, remove tires remove lower tie rod , remove nut in center of the rotor and pull wheel assembley to the side hanging from the strut, pull axle out replace the transmission seal, push new axle in. When putting wheel assembley on, use a hydraulic jack on bottom of the rotor to push it to the axle splines and put the new nut on .

Posted on Jan 15, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

96 Cavalier Auto Trans left turn and stop


Trans fluid maybe low, and/or trans filter stopped-up. Drop pan...change filter...replace fluid.

Oct 03, 2012 | 1996 Chevrolet Cavalier

1 Answer

I have a 91 Taurus GL 3.0 V6 w/auto trans. On transaxle half shafts, do I have to take the passenger side off first. Also do I need to use a differential rotator tool to drive out the other half shaft....


You can take out either half shaft first. Doesn't matter. Yes you should install a new axle nut, if you bought new/rebuilt halfshafts they come with one. I have never had to use a special tool to get the shafts out. I also haven't had to replace the strut to knuckle bolt.

May 25, 2011 | 1991 Ford Taurus

1 Answer

96 Chevy Cavalier, auto, 2.2ltr When I shift from park into reverse it doesn't grab until I give it some gas and then 'clunks' into gear; and when I try to put it into drive it does the same thing. It is...


sounds like it might be a little low on trans fluid,and if i remember correctly these vehicles dont have a trans dipstick to check fluid level,but i could be wrong..if it does check it with the car running on a level surface and in park,hope this helps

Nov 12, 2010 | 1997 Chevrolet Cavalier

1 Answer

How do you remove axle shafts from transaxle on a 99 chevy cavalier is there a clip that needs removed first?


Put a prybar between the shaft and the transmission and try to pop it out, it has a circlip holding it in. You don't remove the clip, it compresses when the shaft pops out.

May 17, 2010 | 1999 Chevrolet Cavalier

1 Answer

I need to Know where the speedometer sensor is on a 1991 chevy cavalier Z24 3.1 mutiport with an Automatic transmission 2WD


The speed sensor for your 1991 Chevy Cavalier Z24 is located on the transmission just inboard of where the passenger side drive axle enters the trans-axle.

Feb 16, 2010 | Chevrolet Cavalier Cars & Trucks

1 Answer

When the car is cold the trans slips reall bad it wont move but if i let the car warm up for ten or fifteen it moves just fine any ideas its a 96 z24 cavalier


There could be a number of different problems here, the first thing I would check or get checked is the transmission oil levels, most auto-matic trans have a bilt in safety, when the oil is low it will not engage or drive..

Feb 05, 2010 | 1997 Chevrolet Cavalier

2 Answers

Where is the dip stick for the trans fluid located? Automatic trans is shifting hard. 2005 Chevy Cavalier.


this model has a sealed transmission, there is no dipstick, the dealer has a special tool for checking the level at a plug just over the driver side axle.

Sep 28, 2009 | 2005 Chevrolet Cavalier

1 Answer

My 96 chevy cavalier ,has a standard tranny , all the sudden it will not go into reverse , but it goes into drive.


will it go in with engine not running? if so look at slave or clutch master to be bad or clutch needs replacement,,,if it will not go into gear with engine not running,repair trans. or replace trans.

Jul 06, 2009 | Chevrolet Cavalier Cars & Trucks

1 Answer

Chevy Transmission Diagram


I have a 1998 olds Regency frt whl drive auto trans. Do not know the trans ref like 460 e? or what.
Any how have had a frt growl, vib @ 65 mph, up and down ride at 10mph. New balanced tires replaced lh whl bearing by guess mechanic said th whl brg was ok.
Latest Son checked the drive axles for movement--there is up and dn movement @ shaft into trans end --lh & Rh side also clunkie noise. Trans seal not leaking,yet.
I suspect brgs or a bushing in trans end as it accepts the drive axle. If it the problem is it replaceable after axle removeable??
John Pankow jpankowsenior@verizon

Oct 26, 2008 | 1993 Chevrolet Cavalier

Not finding what you are looking for?
2006 Chevrolet Cavalier Logo

686 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

70346 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6869 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...