Question about Dodge Ram 1500

1 Answer

Where is the turn signal fuse ? which # - Ram 1500 Dodge Cars & Trucks

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 4 Answers

If your blinkers are not working, check brake lights as well. there is a large fuse in the under-hood fuse box(depending on the year). if i remember right blinker/brake run on same circuit. i fixed the trailer wiring on a 2000 dodge that was blowing that particular fuse.

Posted on Jan 15, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The fuse for a right turn signal on a 2001 Buick Park Avenue


The left an right turn signals get there power from same fuse ,HZDT/SG fuse 15amp in the left under hood fuse box. through the turn signal hazard flasher module. Here is how they work .
Turn Signal/Cornering Lamps
The HZDT/SIG fuse in the fuse block - underhood - left supplies battery positive voltage to the turn signal/hazard flasher module and have ground at G202. The turn signal lamps may only be activated with the ignition switch in the ON or ACCY position. The T/SIG fuse in the fuse block - underhood - left supplies battery positive voltage to the turn signal switch. When the turn signal switch is placed in either the left or right position, current flow is from the turn signal switch assembly to the turn signal/hazard flasher module. The turn signal/hazard flasher module then sends an on-off voltage signal to either the left or right turn signals and their instrument cluster (IPC) indicator. When the hazard switch is pressed, all the turn signal lamps will flash including both IPC turn signal indicators. The left turn signals have ground at G106, G400 and at G402. The right turn signals have ground at G105 and G400. The turn signal switch supplies battery positive voltage to the cornering lamps, the left cornering lamp has ground at G105 and the right cornering lamp has ground at G106.The turn signal switch or the turn / hazard flasher module is bad or there is a wiring problem. Go to you tube an check out a few videos on basic electrical testing ,then get a DVOM - digital volt ohm meter , an wiring diagram an trouble shoot the circuit . There may even be a video on test turn signal circuit .

Dec 04, 2015 | Buick Cars & Trucks

1 Answer

My right front turn signal not working the bulbs are good and so is the fuse but I don't have fire going to them it's a 2010 chevy 2500hd


You don't have fire , never heard it called that before ! Battery voltage , power but never fire ! An open CTSY fuse located in the I/P fuse block will affect the operation of the right front turn signal only
Turn Signal/Hazard Lamps When the turn signal switch is placed in either the left or right position, a ground signal is completed from the turn signal switch to the BCM. When the hazard flasher switch is activated, a ground signal is completed from the turn signal/hazard switch to the BCM. The BCM then sends an ON-OFF voltage signal through the fuses to the appropriate turn signal and side repeater (export only) lamps or to all of the turn signal fuses for hazard operation. The driver door switch and passenger door switch also receive voltage from the BCM turn signal supply voltage circuits for the mirror turn signals. The door switches have no function or control of the mirror turn signals other than a pass through connection for the circuits. The audio chime is also activated when the turn signals are ON. The instrument panel cluster (IPC) receives the signals to activate the turn signal indicators over the GMLAN serial data system. When the hazard switch is pressed, all turn signal lamps will flash including both IPC turn indicators.
Ground is applied at all times at G201 to the turn signal/multifunction switch. The turn signal lamps may only be activated with the ignition switch in the ON or START position. When the turn signal/multifunction switch is placed in either the TURN RIGHT or TURN LEFT position, ground is applied to the body control module (BCM) through either the right turn or left turn signal switch signal circuit. The BCM then applies a pulsating voltage to the front and rear turn signal lamps through their respective control circuits.
.

Jun 25, 2015 | Cars & Trucks

1 Answer

What can I do to fix my turn signals on a2000 caravan?


If the fuse is good then look at the turn signal switch on the column. 99% of inop signals are caused by the switch. If the fuse blows only when you apply a turn signal with the switch, there is a pinched wire or a short in the turn signal wiring.

Aug 27, 2014 | 2000 Dodge Caravan

4 Answers

Turn signal lights don't work


The first place to start are fuses, check your owners manual for location, typically left side of dash.

The emergency (hazard) flashers and turn signals are on separate fuses and run through the hazard switch. If all the lights work when the hazard switch is on then the problem will likely be a blown turn signal fuse.

Other possibilities are the hazard switch itself is bad, the turn signal switch is bad or a broken wire, all of which require a meter (or test light) wiring diagram and knowledge of the circuit to test it - better to have it done.

Robert Grove
Mobile Mechanic Malibu 310 651 8020 Auto Truck RV Mobile Repair...

Aug 09, 2014 | 2002 Chevrolet Impala

1 Answer

2010 chevy equinox right rear turn signal doesnt work, replaced bulb and still the same. front works, is there a fuse for the rear light and where is the fuse located.


RT/SIG fuse #11 15amp - I/P fuse box . Fuse Block - I/P
In the center of the instrument panel, beneath the right side of the radio, in back of the right side console access panel.
This fuse is power to the BCM , When you put on the right turn signal , this is a voltage signal to the BCM . With logic ( programming ) the BCM then controls the turn signal !
Turn Signal/Hazard Lamps
The body control module (BCM) is responsible for controlling the turn signals and hazard lamps. When the turn signal switch is placed in either the left turn or right turn position, the BCM receives a signal from the turn signal switch. The BCM then sends an on-off voltage signal to either the left or right turn signals and their instrument panel cluster (IPC) indicator. When the hazard switch is pressed, the BCM receives a signal from the hazard switch. The BCM then will send an on-off voltage signal to all the turn signal lamps. All the turn signal lamps will flash including both IPC turn signal indicators.
There could be a DTC- diagnostic trouble code stored in the BCM pointing to the problem ! I suggest you take your vehicle to the dealer or a ASE certified repair shop that has the diagnostic tools to find the problem . Just so you don't waste your money replacing parts that don't fix it.
There could

Dec 14, 2012 | 2005 Chevrolet Equinox

1 Answer

2003 cavalier turn signal fuse


The 10A TURN-B/U fuse in the instrument panel fuse block feeds the turn/hazard flasher and the back-up lamps. There could be a short in the flasher, the turn signal/multifunction switch, or the lamps/sockets. There also could be a short in the back-up lamp circuit

Oct 27, 2012 | 2003 Chevrolet Cavalier

2 Answers

All turn signals on my jeep cheroke laredo are not working. Is the problem a bad fuse??


COULD BE BLOW FUSE.FAULTY TURN SIGNAL SWITCH OR FAULTY TURN SIGNAL FLASHERS WHICH IS LOCATED FUSE / RELAY BOX JUST LEFT OF THE STEERING COLUMN.

Dec 05, 2010 | 2003 Jeep Grand Cherokee

2 Answers

My toyota 92 pickup truck turn signals don't work;


Try changing out your turn signal flasher.it might be under your dash by your fuse box.Some trucks have two one for turn signals one for 4 way flashers.By all means check the fuse first.

Mar 09, 2010 | Toyota Pickup Cars & Trucks

1 Answer

1997 Chevy Tahoe both turn signals stopped working


Sounds like the flasher unit to me. Normally the emergency flasher and turn signal are separate.

Jul 21, 2009 | 2001 Chevrolet Tahoe

1 Answer

My turning signals dont work where is my fuse box


The fuse box containing the turn signal fuses is under the hood forward of the brake master cylinder on the drivers side.
The bottom of the fuse cover should show you which one of the fuses is the left turn signal and right turn signal fuse.
Good luck,
Regards,

Jun 18, 2009 | 2002 Chevrolet Silverado

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

463 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

63577 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...