Question about 1992 Dodge Spirit

1 Answer

Fuel problems need step by step instructions on fuel system from front to tank

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

My car is not getting gas.. and wont start... i need to know where the fuel filture is at and the fuel pump.

Posted on Mar 16, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Is there a fuel filter for each tank on a 1997 F350 crew cab 4x4 with a 460


There should be one filter per tank. If there is start with changing the fuel filter in the front tank and if you are still having problems then your front fuel pump seems like it may be going out.

Jul 25, 2014 | 1997 Ford F350 Crew Cab

5 Answers

Www.datadiy.com


Are you serious ? :)
Next to your driver seat there's a little handle to open the fuel door.

Jun 17, 2014 | 2000 Mazda MPV

1 Answer

92 geo metro fuel pump replacement


unhook all fuel lines also fillertube remove bolts from holddown straps.lower fuel tank using floorjack.remove srews at top of tank.remove pump assembly change pump reinstall.

Nov 06, 2012 | Cars & Trucks

1 Answer

Can I access the fuelpump through the trunk on a 94 concours c4.6


According to the instructions, it is not accessible through the trunk on the 94 Cadillac --- REMOVAL AND INSTALLATION Fig. 1: Fuel pump unit 8470h037.gif
  1. Disconnect the negative battery cable.
  2. Relieve fuel system pressure.
  3. Remove fuel filler cap to release fuel tank vapors. Leave cap off until repairs are completed. Gasoline fuel vapors are extremely flammable. Ensure that fuel is stored in a container that can be properly sealed. Never store fuel in an open container. Store container in a safe place away from heat.
  4. Remove fuel tank by performing the following:
    1. Step 1: Drain fuel from the tank into an approved container for storage.
    2. Step 2: Raise and safely support the vehicle.
    3. Step 3: Remove rear stabilizer bar at links, pivot bar downward.
    4. Step 4: Remove hoses and pipes from tank unit.
    5. Step 5: Remove hoses at tank from filler and vent pipe.
    6. Step 6: Disconnect tank unit harness from rear body harness.
    7. Step 7: Support fuel tank and disconnect 2 fuel tank retaining straps.
    8. Step 8: Remove tank from vehicle.
  5. Remove sending unit, gasket and pump assembly by turning cam lock ring counterclockwise. Lift assembly from fuel tank and remove fuel pump from fuel tank sending unit.
  6. Pull fuel pump up into attaching hose while pulling outward away from bottom support. Take care to prevent damage to rubber insulator and strainer during removal. After pump assembly is clear of bottom support, pull pump assembly out of rubber connector for removal. To install:
  7. Push fuel pump assembly into attaching hose.
  8. Install fuel tank sending unit and pump assembly into tank assembly. Use new O-ring seal during reassembly.
  9. Install cam lock over assembly and lock by turning clockwise.
  10. Support tank and position in vehicle. Install tank straps and secure with retaining bolts. Tighten to 25 ft. lbs. (33 Nm).
  11. Connect tank unit harness to body harness.
  12. Connect hoses to filler and vent pipes. Tighten clamps.
  13. Connect hoses and pipes to tank unit.
  14. Connect rear stabilizer bar to links. Tighten bolts to 42 ft. lbs. (58 Nm).
  15. Lower vehicle.
  16. Refill tank and install filler cap.
  17. Connect negative battery cable.
  18. Start engine and check for leaks.
prev.gif next.gif

Aug 26, 2010 | Cadillac Escalade ESV Cars & Trucks

2 Answers

Cant unscrew fuel pump plastic cover


there is a special tool to do this, but I just use a giant pair of channel locks

Nov 13, 2009 | Cars & Trucks

1 Answer

How do you get the top of a fuel tank off of a 2001 ford expedition? We are trying to replace the fuel filter.


Ford Excursion, Expedition, Lincoln Navigator 2000-2005

2001 Ford Truck Expedition 4WD 5.4L EFI 8cyl

Fuel Tank - Removal & Installation
CAUTION Do not smoke or carry lighted tobacco or open flame of any type when working on or near any fuel-related components. Highly flammable mixtures are always present and may be ignited. Failure to follow these instructions may result in personal injury.
CAUTION Fuel in the fuel system remains under high pressure even when the engine is not running. Before working on or disconnecting any of the fuel lines or fuel system components, the fuel system pressure must be relieved. Failure to follow these instructions may result in personal injury.
  1. Before servicing the vehicle, refer to the precautions section.
  2. Disconnect the battery ground cable.
  3. Relieve the fuel pressure.
  4. Drain the fuel from the fuel tank.
  5. Raise and support the vehicle.
  6. Disconnect the fuel tank filler pipe hose and the filler pipe vent tube from the fuel tank.
  7. Position a jack under the fuel tank
  8. Remove the four fuel tank cover strap bolts
  9. Partially lower the fuel tank
  10. Disconnect the fuel lines from the fuel pump.
  11. Disconnect the fuel pump electrical connector
  12. On gasoline fuel tanks, disconnect the hose(s) from the evaporative emission valve.
  13. Lower the fuel tank
  14. If a new fuel tank is being installed, transfer the necessary components to the new fuel tank.
  15. To install, reverse the removal procedure and note the following:
  16. Tighten the fuel tank strap bolts to 98 ft. lbs. (133 Nm).
CAUTION Do not smoke or carry lighted tobacco or open flame of any type when working on or near any fuel-related components. Highly flammable mixtures are always present and may be ignited. Failure to follow these instructions may result in personal injury.
CAUTION Fuel in the fuel system remains under high pressure even when the engine is not running. Before working on or disconnecting any of the fuel lines or fuel system components, the fuel system pressure must be relieved. Failure to follow these instructions may result in personal injury.
WARNING Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is therefore essential that absolute cleanliness is observed when working with these components. Always install blanking plugs to any open orifices or tubes.
  1. Before servicing the vehicle, refer to the precautions section.
  2. With the vehicle in NEUTRAL, position it on a hoist.
  3. Release the fuel system pressure.
  4. Drain the fuel tank.
  5. If equipped, remove the four nuts and the fuel tank skid plate.
  6. Disconnect the two vapor tubes at the rear of the fuel tank
  7. Disconnect the vapor tube and the fuel filter outlet tube forward of the fuel tank.
    NOTE Do not support the fuel tank directly beneath the fuel pump mounting area. Damage to the fuel pump assembly can occur.
  8. Position a suitable jack under the fuel tank.
    NOTE The location of the fuel vent hose is critical to fuel system operation. Note the routing of the fuel vent hose at this time.
  9. Remove the two bolts and the fuel tank front and rear support straps. Lower the front of the fuel tank approximately 1 inch. (25 mm).
  10. Disconnect the vent tube from the fuel pump module.
  11. Disconnect the fuel pump module and fuel pressure transducer electrical connectors.
  12. Remove the fuel tank from the vehicle.
  13. To install, reverse the removal procedure and note the following:
  14. For 2005 models if removed, tighten the fuel tank skid plate bolts to 15 ft. lbs. (20 Nm). For 2006 models 22 ft. lbs. (30 Nm).
  15. For 2005 models tighten fuel tank strap bolts to 35 ft. lbs. (47 Nm). For 2006 models tighten strap bolts to 30 ft. lbs. (40 Nm).


Fuel Pump - Removal & Installation

CAUTION Fuel injection systems remain under pressure, even after the engine has been turned OFF. The fuel system pressure must be relieved before disconnecting any fuel lines. Failure to do so may result in fire and/or personal injury.
  1. Before servicing the vehicle, refer to the precautions section.
  2. Remove or disconnect the following:
    Negative battery cable Fuel pressure Fuel tank skid plate bolts and lower the skid plate Fuel Fuel tank filler pipe hose from the tank Fuel tank filler pipe vent hose from the tank Fuel lines from the fuel pump Front fuel tank connections Rear Evaporative Emissions (EVAP) hose clamp and the hose Electrical connector from the fuel pump
  3. Support the fuel tank with a jack.
    Fuel tank support strap bolts and the fuel tank straps Fuel tank Fuel pump lock ring Fuel pump

More details in autozone.com (free register).

Hope helped (remember rated thie help).

Oct 19, 2009 | 2001 Ford Expedition

1 Answer

Do you have to drop fuel tank to change fuel pump on 93 mark v111


The fuel pump is a submerged type located inside the gas tank. You need to drop the tank to get to it since it goes in thru the top. Major undertaking, The fuel FILTER is located behind the cowling on the passenger side front wheel well. Better get a shop/Chilton manual if you plan on doing it yourself or you can pick up the fuel pump at Auto Zone and they can give you the step by step instructions to getting the job done with common tools. Good luck and be safe, keep me posted be glad to answer any questions you may have.

Jul 14, 2009 | 1993 Lincoln Mark VIII

2 Answers

Need instructions on changing fuel pump in a 2000 ford windstar


Tank—Fuel Removal
ani_caut.gif WARNING: Do not smoke, carry lighted tobacco or an open flame of any type when working on or near any fuel-related component. Highly flammable mixtures are always present and may ignite, resulting in possible personal injury.
ani_caut.gif WARNING: Fuel in the fuel system remains under high pressure even when the engine is not running. Before servicing or disconnecting any of the fuel system components, the fuel system pressure must be relieved to prevent accidental spraying of fuel causing personal injury or a fire hazard.
NOTE: The fuel tank comes equipped with a composite protective shield mounted with the support straps on the right side of the fuel tank. Make sure the protective shield is installed correctly whenever the fuel tank is installed.
  1. Disconnect the battery ground cable. For additional information, refer to Section 414-00.
  1. Relieve the fuel pressure. For additional information, refer to Section 310-00.
  1. Drain the fuel tank. For additional information, refer to Section 310-00.
  1. Raise and support the vehicle. For additional information, refer to Section 100-02.
  1. Remove the fuel tank filler pipe hoses.
    • Remove the clamps.
    av1551a.gif
  1. Disconnect the fuel pump connector.
    av1552a.gif
  1. Disconnect the tank connections:
    1. Disconnect the fuel lines. For additional information, refer to Section 310-00.
    1. Disconnect the vapor tube fitting. For additional information, refer to Section 310-00.
    av1553a.gif
  1. Remove the center fuel tank strap bolt and remove the support strap.
    av1554a.gif
  1. Position a safety support under the fuel tank.
  1. NOTE: Safety support not shown for clarity.
    Remove the fuel tank support strap bolts.
    av1556a.gif
  1. Partially lower the fuel tank while swinging the fuel tank support straps away from the fuel tank. Remove the straps and lower the fuel tank.
Installation
  1. To install, reverse the removal procedure.
    av1557a.gif
    av1555a.gif
    Module—Fuel Delivery
    Special Tool(s) st1698b.gif Fuel Sender Wrench
    310-069 Removal
    1. Remove the fuel tank (9002). For additional information, refer to Tank—Fuel in this section.
    1. Clean the area around the fuel pump mounting flange.
    1. Remove the fuel module connections:
      1. Disconnect the fuel tank pressure sensor electrical connector.
      1. Disconnect the fuel fittings. For additional information, refer to Section 310-00.
      av1559a.gif
    1. If repair or installation of new fuel lines or a new electrical harness is necessary, remove the fuel lines or harness from the fuel tank retaining clips and remove the appropriate assembly.
      av1560a.gif
    1. Using the special tool, remove the fuel module retaining ring.
      a0023621.gif
    1. ani_caut.gif CAUTION: The fuel delivery module must be handled carefully to avoid damage to the float arm and filter.
      Remove the fuel delivery module from the fuel tank.
    Installation
    1. NOTE: Make sure that the areas around the fuel delivery mounting area and the fuel delivery module flange are clean.
      NOTE: When installing the fuel delivery module, make sure to align locator tabs on the fuel tank mounting flange.
      To install, reverse the removal procedure.
      av1563a.gif
      a0023620.gif

May 26, 2009 | 2000 Ford Windstar

1 Answer

How do you drop the fuel tank on a 1993 CAVALIER?


Remove the filler neck hoses, unplug the electrical connector, disconnect the fuel lines. Remove the tank strap bolts, and remove the tank. Turn the retaining ring on the sending unit counterclockwise, pull the pump and sending unit outof the tank.
I believe that the pump and sending unit come as an assembly on this one and that is why the price is so high.

I do not recommend using any electrical fuel system parts from the junk yard because as they sit around, the varnish on the wires inside the pump deteriorates and then short out. Same thing with fuel injectors.

Have you priced a pump at the local parts stores? NAPA, Auto Zone, etc. They can give step by step instructions to drop the tank and remove the fuel pump if that's what your trying to do. goos luck. Oh and the step by step's are free at Auto Zone.

May 09, 2009 | 1993 Chevrolet Cavalier

1 Answer

In-the-tank fuel pump r&r


Here are instructions for replacment with a diagram of the fuel pump components my only suggestion would be instead of draining the tank and dropping the fuel tank if you unbolt the box and using a jack and and some wood lift the fuel tank side of the box this will give you access to the tank and fuel pump/ sending unit. It will save you time and the hastle of replacing the tank straps which are prone to snapping at the threads when trying to remove the nuts.If these brake you will have to replace them.

Nov 16, 2008 | 1994 GMC Sierra

Not finding what you are looking for?
1992 Dodge Spirit Logo

Related Topics:

96 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

63242 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...