Question about 2003 Toyota Sienna

1 Answer

Sienna 2003 tail lights on the corner and from the lift-gate

I need to remove and replace the tail lamps on my Sienna 2003. Does the same technique of a little more force apply, once the two obvious bolts to both sets of lights have been removed?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 31 Answers

Yes. there are 2 or 3 clips that must be somewhat forced out. so carefully, but forcefully pop the taillamp assy. out and change the bulbs.

Posted on Jan 14, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I replace a burned out rear backup light


Open the liftgate. Remove the liftgate applique. Refer to Liftgate Applique Replacement in Body Rear End. Remove the back up lamp socket (1) from the liftgate applique by turning the socket (1) counterclockwise. Remove the back up lamp bulb from the socket.
Lift gate Applique Replacement
Remove the lift gate trim panel. Refer to Lift gate Trim Panel Replacement .
1
Lift gate Applique Nuts (Qty: 5)
Tip
Disconnect the electrical connector.
Tighten
10 N?·m (89 lb in)
2
Lift gate Applique

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

May 10, 2016 | 2004 Cadillac SRX

1 Answer

The handle broke off on my 2003 jeep grand cherokee laredo liftgate. how can i open it now? i can't find anything on the inside in the back and my tail light is out.


You will need to remove the interior panle from the loft gate to axess the latch
there is 4 screws along the bottom of the panle to remove then carfuly pull the panle away from the lift gate there is plastic clips that hold the panle to the gate these may need to be replaced when re installing the panle they can be purchased at the jeep dealer.
now look into the lift gate and you will see where the handle rod conects to the latch lift on this rod and the gate will open
to replace the handle remove the 2 10 mm bolts and disconect the rod from the latch install the new handle and rod to the latch install the 2 10 mm bolts. install the panle and 4 screws
this should cover it

Jul 13, 2010 | 2003 Jeep Grand Cherokee

2 Answers

How to change a turn signal bulb


If it is for the turn signal bulb for the tail light, here ya go:

Tail Lights
  1. Open the lift gate.
  2. Remove the screws from the tail lamp and pull the tail lamp from the body.
  3. Disconnect the electrical connector from the tail lamp.
To install:
  1. Connect the electrical connectors.
  2. Install the tail lamp and tail lamp mounting screws.
  3. Close the lift gate.


6060e5e.gif
Tail lamp detail view

Jun 08, 2010 | 2002 Chevrolet Venture Passanger

1 Answer

How to change a rear turn signal lamp on a 2005 dodge caravan


I am including a couple of illustrations to better help with this replacement.
You will first need toe open the tail gate. then next to the tail light on the inside edge where the tail gate meets the seal you will see to plastic screw covers ( if still there) or two screws. You will need to remove these two screws , once removed the tail light will come out by lightly pulling outwards. Then simply depress the thumb clip on the bulb holder and remove.
9697c49.jpg





3724ffb.jpg


May 25, 2010 | 2005 Dodge Caravan

1 Answer

Drivers side rear blinker light needs replaced


Open the tail gate, and you will see on the side of the tail light housing two screws that you will need to unscrew in order to take the housing out. If it is the tail light ,that is on the actual gate, open the tail gate and remove the plastic bed liner there are few of screws that need to be removed. Hope this helps you fix it.

Apr 17, 2010 | 2003 Subaru Baja

1 Answer

Rear door on 2001 sienna won't open


The door handle might be broken, you need a new part. I got mine online for $40. keywords: 2001 2002 2003 2004 2005 2006 2007 Toyota Sequoia Metal Lift Gate Exterior Door Handle for Rear Outside Van Tailgate Handle. You need to remove the back door panel to replace this.

Mar 06, 2010 | 2001 Toyota Sienna

1 Answer

How to replace a trunk lift on 2005 toyota sienna. The back tail gate will not stay up and I have purchased two new trunk lifts. Not sure how to change them


look at the ends there are small clips that hold it in place you will need a small screwdriver to remove them and have someone hold it up then they just pop off

Mar 01, 2010 | Toyota Sienna Cars & Trucks

1 Answer

Rear tail light lens removal I need to replace the brake light bulb, but I do not see a way to remove the lens cover. I do not want to bust the one I have in order to fix the problem


Hello riggs791. My name is Roger and I will help you. Raise the lift gate. In the rain drip rail you will find two screws through the lens to the body. Remove the two screws. Carefully pull on the lens. What you are removing to get to the tail lamp bulb is the entire lamp. The front outside edge of the lens has two lock in clips. Once you have the lamp loose turn it over and unlock the socket and replace the light. Reverse to reinstall the lamp.
Should you need further help please just ask. Please rate the quality of your answer. This way we know the answer helped. Thank You for using Fix Ya. Roger

Sep 26, 2009 | 1999 Ford Explorer

1 Answer

I need to replace the whole rear tail gate lamp assembly.


Yeah remove the inside panel to get to those bolt, they should be 10mm nut.

Aug 12, 2009 | 2008 Toyota Sienna

2 Answers

How do I replace the Rear Brake light bulb of 2001 Toyota Sienna?


I have a 2001 Sienna and have had to replace most of my tail light bulbs.

The bulbs that are mounted in the fender (wrap arounds) have acess panels in the van's interior that easily pop out and expose the back of the light assembly.

However, the bulbs that are found in the lift gate are a different matter. You have to remove the whole interior panel to the lift gate to expose the light assemblies. Go to your auto parts store and get a tool to help pop out the plastic retainers from the lift gates metal frame. Don't force the retainers out. Go slowly and gently so that you don't damage the interior panel. If you are really gentle you might even get to reuse the retainers.

Good luck!

Jun 08, 2009 | 2001 Toyota Sienna

Not finding what you are looking for?
2003 Toyota Sienna Logo

Related Topics:

342 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...