Question about 2004 Kia Rio

1 Answer

Something not right about my transmission ... cuz i never had grinding nosie on it n it was running find then my transmission went out ... out of the bule..... is it the wirring or the transmission filter?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 31 Answers

The transmission probably needs to be replaced. there are a series of tests that need to be run to be sure, but i have done quite a few of those transmissions.

Posted on Jan 14, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Replaced clutch master cylinder work find, but grinding nosie bottom inside clutch


I don't fully understand your question but if the clutch is working and just makes a grinding noise when you depress the clutch pedal, it is probably a bad throw-out bearing.

May 28, 2014 | 1996 Chevrolet K1500

1 Answer

A knocking and grinding noise coming from underneath the car,


if you had the CV JOINTSreplaced , they both should have lasted for a long time, how much do you trust your mechanic ? always something to consider ! also, the mechanic who replaced the CV'S last time, did he do a good job ? was there a grinding noise then ? did you get a warranty on the previous cv's, I'm not tryin to point any fingers, just sayin, you need to be aware of every move you make, and who you make it with. NOW, go to good transmission shop, have them test drive ,with you in car, and inspect your front end and transmission, its free , good luck

Feb 17, 2013 | 1999 Chevrolet Malibu

1 Answer

Right rear tire grinding


you may have bearings going out

May 07, 2012 | 1995 Subaru Impreza

1 Answer

Why whould antifreeze be brown?


its brown cuz the motor is metal and it rusts internally when sitting for periods of time, reccomend a coolant flush where they use a chemical to clean it out. it may not be shifting cuz the transmission cooling line runs thru the radiator and may not be cooling right due to a clog or obstruction in line. who ever flushes it should be able to check that for you.

Feb 28, 2012 | 1997 Chevrolet Suburban

1 Answer

When i went to crank my car i got full battery power but when it went to crank up it made a loud grinding noise and will not start. if its my starter where is it located? I have a 1990 Honda Accord


it will be located at transmission going from engine side into bell housing in transmission ,not sure wheter it left or right side but thats where it will be
i presume it s an automatic transmission
if it is a stick as you call it you can start on a push

Feb 01, 2011 | 1990 Honda Accord

1 Answer

Grinding noise upon turning. Only audible in interior - sounds like 4-wheel drive is about to die!


If you hear the nosie when turning right or when turning left? Have you checked your front or back brake pad linings? It sounds like you have a bad bearing,cv axle or ujoint, . Where do you here the noise from? Front or back or left or right?

Nov 16, 2010 | 2000 Jeep Grand Cherokee

1 Answer

Wont start locks wont work had transmission cooler/line replaced


check wiring and connectors at battery and fuses look at starter and see and feel if its loose or not sitting right if it is notify shop dealership where work was done possible did not install starter correctly when work on transmission was done grinding, starter not meshing correctly with fly wheel

Nov 25, 2009 | 1998 Chevrolet Cavalier

1 Answer

My transmission went on my 97 acura cl....


the average price of that transmission is about $800 rebuilt, try this site and then its up to the mechanic where you take it for the installation charge

Aug 22, 2009 | 1997 Acura CL

1 Answer

Wierd grinding sound from manual transmission


the clutch release bearing is dry or going bad

Jan 21, 2009 | 1996 Mitsubishi Eclipse

Not finding what you are looking for?
2004 Kia Rio Logo

Related Topics:

97 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kia Experts

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

yadayada
yadayada

Level 3 Expert

64034 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Kia Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...