Question about 2003 Mitsubishi Outlander

Open Question

2.5tdi pajero head bolts torque

Hi,can anyone please tell me what torque/degrees these bolts need please? i have new bolts £65.00

Posted by on

3 Suggested Answers

emissionwiz
  • 61272 Answers

SOURCE: head torque settings

The torque is 90 foot lbs, and they want you to use new bolts, the old ones are stretched and CAN NOT be reused, tighten 20 lbs at a time in proper sequence as outlined in service manual.

Posted on Dec 03, 2008

junmag
  • 161 Answers

SOURCE: Blown head gasket

i think you are reffering to a 4D56 engine. just type 4D56 workshop manual .pdf download on your browser and you fill find several free downloads. everything you need to overhaul the engine is there

Posted on Jun 02, 2009

  • 510 Answers

SOURCE: I followed the haynes manual to tighten up the

Cylinder head
Renew bolts Yes
Stage 1 Tighten 50 Nm
Stage 2 Tighten 100 Nm
Stage 3 Slacken off 360°
Stage 4 Tighten 50 Nm
Stage 5 Tighten 90°
Stage 6 Tighten 90°
Stage 7 Tighten M8=24 Nm

Posted on Feb 12, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

HEAD BOLT TORQUE SPECS FOR MITSUBISHI TRITON 3.2 DIESEL 4M41U ENGINE - THANK YOU


there's no one torque setting. there's multiple stages and a sequence you have to do it in. usually finger tight, then tighten to a torque setting spiraling out. then torque it further so many degrees.
check the pajero 4m44 forum for exact specs. got manual at hm. have look later.

Jun 28, 2016 | Mitsubishi Cars & Trucks

1 Answer

What is the cylinder block torque specification


Assuming head torque follow this sequence:

1st 54 ft lb, 2nd loosen all bolts, 3rd 15 ft lb,
4th turn 90 degrees, 5th turn 90 degrees

Torque sequence:
8 6 1 3 9
10 4 2 5 7

May 19, 2014 | 2006 Mitsubishi Pajero 3.2

2 Answers

2002 nissan maxima 3.5 cylinder head torque


Hi there:

2_17_2012_6_58_18_pm.jpg

Fig. Cylinder head bolt loosening sequence - Altima & Maxima 3.5L engine

Install the cylinder head bolts and torque in sequence as follows:
  1. Step 1: 72 ft. lbs. (98 Nm).
  2. Step 2: Completely loosen all bolts.
  3. Step 3: 26-32 ft. lbs. (34-44 Nm).
  4. Step 4: plus 90-95 degrees clockwise.
  5. Step 5: plus 90-95 degrees clockwise.

2_17_2012_6_59_54_pm.jpg

Fig. Right cylinder head bolt torque sequence- Altima & Maxima 3.5L engine


2_17_2012_7_00_21_pm.jpg

Fig. Left cylinder head bolt torque sequence- Altima & Maxima 3.5L engine

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day

Feb 17, 2012 | Nissan Cars & Trucks

1 Answer

Cylinder head bolt torque specs for 2000 Cadillac catera 3.0L 6 cyl


YOU NEED NEW HEAD BOLTS OLD HEAD BOLTS BEEN STRETCHED. YOU HAVE TORQUE HEAD BOLTS IN FIVE PASSES. FIRST PASS TORQUE HEAD BOLTS 18 FT LBS. SECOND PASS ADD ADDITIONAL 90 DEGREES.THIRD PASS ADD ADDITIONAL 90 DEGREES.FOURTH PASS ADD ADDITIONAL 90 DEGREES.FIFTH PASS ADD 15 DEGREES.

Dec 22, 2010 | 2000 Cadillac Catera

1 Answer

Need torque settings for cylinder head bolts on a 52 reg skoda fabia 1.4 16v any help much appreciated thanks


Torque settings for cylinder head bolts for Skoda Fabia 1.4 16v

Cylinder head bolts tightening order:

tdisline_116.jpg

IMPORTANT NOTE: RENEW BOLTS!

Stage 1: Tightening torque = 30 Nm
Stage 1: Tightening torque = 90 Degrees
Stage 1: Tightening torque = 90 Degrees

Please do rate my response. Thanks!

Dec 17, 2010 | Volkswagen Polo Cars & Trucks

2 Answers

I need lower manifold rocker and upper manifold torque instructions please help


Head Bolts
Torque sequence --------- ' 6 2 3 7 ' ' 5 1 4 8 ' --------- Step 1: torque in sequence to 33 Ft/Lbs Step 2: turn an additional 90 degrees recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) that permanently stretch during the initial installation.New head bolts must be used when cylinder head is replaced or re-installed to obtain proper torque.Always coat bolt threads with the proper sealant.
The Intake Bolt Torque 10 Foot pounds (Final torque)
Note:to torque bolts & nuts, start in center using crisscross pattern working outward

Dec 05, 2010 | 2000 Pontiac Grand Am GT

1 Answer

Looking for head bolt troque spec for 3.4l impala sfi04


Please don't forget to rate. Thank you:

Left side front cylinder head


98e175a.gif
Cylinder head bolt torque sequence-3.4L engine

  • Cylinder head by aligning it with the dowel pins
  • New cylinder head bolts coated with a sealant (such as GM 1052080). Torque the bolts in the proper sequence (1-8) to 37 ft. lbs. (50 Nm). Using a torque angle meter turn the bolts 90 degrees in the proper sequence.
  • Left side exhaust manifold. Torque the bolts to 12 ft. lbs. (16 Nm).
  • Spark plugs. Torque the plugs 11 ft. lbs. (15 Nm).


  • Right side rear cylinder head:


    71cd5b7.gif
    Cylinder head bolt torque sequence-3.4L engine


  • New cylinder head gasket
  • Cylinder head on top of the gasket and make certain it is lined up properly with the dowel pins
  • New cylinder head bolts coated with a sealant (such as GM 1052080). Torque the bolts in the proper sequence (1-8) to 37 ft. lbs. (50 Nm). Using a torque angle meter turn the bolts 90 degrees in the proper sequence.
  • Right side exhaust manifold. Torque the bolts to 12 ft. lbs. (16 Nm).
  • Spark plugs. Torque the plugs 11 ft. lbs. (15 Nm).
  • Spark plug wires
  • Exhaust crossover pipe. Torque the fastener to 18 ft. lbs. (25 Nm).
  • Valve rocker arms and pushrods. Torque the fastener to 89 inch lbs. (10 Nm). Using a torque angle meter torque the fastener an additional 30 degrees.
  • Lower intake manifold. Torque the bolts to 115 inch lbs. (13 Nm).
  • Upper intake manifold. Torque the bolts to 18 ft. lbs. (25 Nm).
  • Nov 26, 2010 | 2004 Chevrolet Impala

    2 Answers

    Head gasket torque specifications and sequense


    Please don't forget to rate. Thank you:

    Left side front cylinder head


    98e175a.gif
    Cylinder head bolt torque sequence—3.4L engine

  • Cylinder head by aligning it with the dowel pins
  • New cylinder head bolts coated with a sealant (such as GM 1052080). Torque the bolts in the proper sequence (1-8) to 37 ft. lbs. (50 Nm). Using a torque angle meter turn the bolts 90 degrees in the proper sequence.
  • Left side exhaust manifold. Torque the bolts to 12 ft. lbs. (16 Nm).
  • Spark plugs. Torque the plugs 11 ft. lbs. (15 Nm).


  • Right side rear cylinder head:


    71cd5b7.gif
    Cylinder head bolt torque sequence—3.4L engine


  • New cylinder head gasket
  • Cylinder head on top of the gasket and make certain it is lined up properly with the dowel pins
  • New cylinder head bolts coated with a sealant (such as GM 1052080). Torque the bolts in the proper sequence (1-8) to 37 ft. lbs. (50 Nm). Using a torque angle meter turn the bolts 90 degrees in the proper sequence.
  • Right side exhaust manifold. Torque the bolts to 12 ft. lbs. (16 Nm).
  • Spark plugs. Torque the plugs 11 ft. lbs. (15 Nm).
  • Spark plug wires
  • Exhaust crossover pipe. Torque the fastener to 18 ft. lbs. (25 Nm).
  • Valve rocker arms and pushrods. Torque the fastener to 89 inch lbs. (10 Nm). Using a torque angle meter torque the fastener an additional 30 degrees.
  • Lower intake manifold. Torque the bolts to 115 inch lbs. (13 Nm).
  • Upper intake manifold. Torque the bolts to 18 ft. lbs. (25 Nm).
  • Mar 06, 2010 | 2001 Chevrolet Venture

    2 Answers

    Cly head torque settings


    The torque is 44 ft lbs+ 95 degrees. You will have to replace all the head bolts/ one time use only. Working from the center out tighten all to 44 ft lbs. Then from center out again go anothre 95 degrees. Good Luck

    May 17, 2009 | 1999 Chevrolet Venture

    1 Answer

    Head bolt toqure


    Hope this helps, from autozone site. Curt
    Application:
    Cylinder head bolt torque sequence

    Note :
    Torque sequence:
    ---------
    front | 3 1 6 |
    of | |
    vehicle | 5 2 4 |
    ---------
    Step 1: Lightly oil cylinder bolt threads & washers
    Step 2: Torque to 22 Ft/Lbs
    Step 3: Torque to 51 Ft/Lbs
    Step 4: Loosen all bolts 180 degrees
    Step 5: Loosen all bolts 180 degrees
    Step 6: Torque bolts 1 & 2 to 25 Ft/Lbs
    Step 7: Torque bolts 3, 4, 5, 6 to 11 Ft/Lbs
    Step 8: Turn all bolts an additional 80 to 90 degrees
    Step 9: Turn all bolts an additional 80 to 90 degrees
    *** CAUTION ***
    engine uses Torque To Yield head bolts (TTY) that
    permanently stretch during the initial installation.
    New head bolts must be used when cylinder head is
    replaced or re-installed to obtain proper Torque.

    Apr 24, 2009 | 1995 Subaru Legacy

    Not finding what you are looking for?
    2003 Mitsubishi Outlander Logo

    Related Topics:

    44 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Mitsubishi Experts

    yadayada
    yadayada

    Level 3 Expert

    61249 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    21949 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    6812 Answers

    Are you a Mitsubishi Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...