Question about 1993 Plymouth Voyager

1 Answer

I need specs onfixin the fuel line

I have 2 holes right out of the tank on the line n on the connector 2 the sending n recieving unit how do i fix it

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 599 Answers

Change line completely from connection to connection is recommended

Posted on Jan 14, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My gas Gage does not work


Could be the gauge on the dash or the sending unit in the tank.

Jul 06, 2012 | 1997 GMC Sonoma

1 Answer

How much to replace a fuel pump in 97 buick lesabre


The fuel pump is inside the fuel tank. To replace it you must remove the fuel lines, fill and vent hoses, and the electrical connector at the fuel tank. Then the two straps holding the tank in place must be released and the tank will come down. A lock ring holds the sending unit and fuel pump in place and must be removed by sliding it counterclockwise, then the sending unit and pump will come out as an assembly. Often the sending unit lines are too corroded to be reused, or are too corroded to release the fuel lines. In that case I cut the steel lines at the sending unit with side cutters, which allows me to take the lines down and position them where I can pick the rust out from the connector sockets and, eventually unlock the fuel lines. The sending unit must be replaced; and I just order complete assemblies ready to drop into the tank. You'll also want to replace the o-rings on the fuel lines.

Aug 01, 2011 | 1995 Buick LeSabre

2 Answers

I need change the fuel pump


Hi, The fuel pump is in the tank. You will have to remove the tank to get at it. Good luck

Jun 21, 2011 | 1995 Ford Windstar

2 Answers

2002 dodge 1500 truck code 0463


Diagnostic Trouble Code (DTC) P0463 is "Fuel Level Sending Unit Volts Too High"
The fuel level sending unit voltage is monitored by the Powertrain Control Module (PCM) when the ignition switch is on and the battery voltage is more than 10.4 volts. This DTC may be stored when the fuel level sending unit voltage at the PCM is more than 9.4 volts for 2 seconds or more. The possible causes are: defective fuel level sending unit , defective connectors or wiring, or a defective PCM.

May 23, 2011 | Dodge Ram 1500 Cars & Trucks

1 Answer

How to change a fuel pump on a 2005 Nissan


Nissan Car Altima & Sentra 1999-06 Repair Guide
Fuel Pump - Removal & Installation
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Relieve the pressure from the fuel system.
  3. Remove or disconnect the following:
    NOTE When the fuel sending unit needs to be removed, pull the tab upwards. The tab is located on the sending unit, opposite the end of the float. After the tab is pulled, the sending unit will lift straight out of the tank bracket.
    Negative battery cable Rear seat and the access cover Fuel pump electrical connector Fuel lines from the fuel pump assembly Locking ring Fuel gauge assembly Fuel tube and connector from the fuel gauge
    Fuel pump by pinching the 2 locking tabs together. Lift the fuel pump assembly straight upward and out of fuel tank. O-ring and discard
  4. Place a clean rag in the hole to keep out dirt.
To install:
  1. Remove the rag
  2. Install or connect the following:
    NOTE Verify that the mark on the fuel tank and the components are aligned when installing the pump and fuel gauge sending unit.
    New O-ring and fuel pump Electrical connection and fuel tube to the fuel gauge sending unit Fuel sending unit into the tank
  3. If equipped with a threaded lock ring torque the ring to 22-26 ft. lbs. (30-35 Nm). If equipped with a lock ring held by six retaining screws, torque the screws to 18-22 inch lbs. (2-2.5 Nm).
    Fuel lines and fuel pump electrical connector. Always install new clamps on the fuel lines. Negative battery cable
  4. Start the engine, check for leaks and repair if necessary.
    Fuel pump access cover Rear seat

The fuel pump is located in the fuel tank on all vehicles. In-tank fuel pumps are accessible by lifting up the rear seat to gain access to the inspection cover.
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Relieve the fuel system pressure.
  3. Remove or disconnect the following:
    Negative battery cable Rear seat from the vehicle Inspection cover that is located under the rear seat Inlet and outlet fuel lines from the fuel pump assembly Fuel pump and gauge wiring connections 6 mounting bolts that secure the fuel pump assembly to the top of the fuel tank
  4. Raise up the fuel pump assembly and detach the fuel tubes and connector.
    Fuel gauge assembly Fuel pump with the fuel chamber
  5. Pull up the front of the fuel pump chamber and slide the chamber forward.
    Fuel pump from the chamber O-ring seal or gasket
To install:
  1. Install or connect the following:
    Fuel pump to the fuel pump chamber and slide chamber rearward Fuel pump with the fuel pump chamber Fuel gauge assembly using a new O-ring Fuel tubes and connector. Use new hoses and clamps. 6 mounting bolts to the top of the fuel gauge unit and torque the bolts to 18-22 inch lbs. (2-2.5 Nm) Fuel pump and gauge wiring connections New inlet and outlet fuel lines to the fuel pump assembly Negative battery cable
  2. Start the vehicle, check for leaks and repair if necessary. Inspection cover and the rear seat

Hope helps (remember comment and rates this).

Jul 07, 2010 | 2005 Nissan Sentra

2 Answers

Changing a fuel pump in a 1999 VP.


Things You'll Need:
  • Ratchet and socket
  • Wrench set
  • Floor jack and 2 jack stands
  • Ratchet extension
  • Fuel tank sending unit wrench number 310-123
  • Screwdriver
  • Slip joint pliers
  • New O-ring seal
  • Clean engine oil
Relieve the Fuel System Pressure
  1. Step 1 Detach the splash shield from the frame rail located underneath the driver's side door. Use a ratchet and socket.
  2. Step 2 Unplug the electrical connector you will see after removing the splash shield. The connector leads to the fuel pump module.
  3. Step 3 Start the engine and let it idle until it stalls. Then crank the engine for about 5 seconds to relieve the remaining fuel pressure from the system. If the engine does not start due to a bad fuel pump, crank the engine to make sure fuel pressure is relieved.
  4. Step 4 Turn the ignition key to the Off position.
  5. Remove the Fuel Pump
  6. Step 1 Disconnect the ground, battery cable from the battery using a wrench.
  7. Step 2 Jack up the rear of your F-150 using a floor jack and support it on 2 jack stands.
  8. Step 3 Remove the tank shield if your particular model is equipped with it using a ratchet, ratchet extension and socket.
  9. Step 4 Support the fuel tank with the floor jack.
  10. Step 5 Disconnect the straps holding the tank to the truck's body using the ratchet, ratchet extension and socket.
  11. Step 6 Lower the fuel tank just enough to gain access to the fuel lines, vapor lines and fuel pump electrical connector on top of the tank.
  12. Step 7 Disconnect the fuel lines and vapor lines from the sending unit/pump module. Press the lock tabs on the lines quick connectors and carefully pull the lines from their fittings. Then unplug the pump-module electrical connector.
  13. Step 8 Release the sending unit/pump module by turning the lock ring counterclockwise using the fuel tank sending unit wrench 310-123 or equivalent. See the Resources box and Tip boxes at the bottom of this article for more information.
  14. Step 9 Lift the sending unit/pump module off the tank carefully and discard the O-ring seal underneath the flange of the module.
  15. Install the Fuel Pump
  16. Step 1 Remove the old fuel pump from the module using a screwdriver and a pair of slip joint pliers and install the new pump on the module.
  17. Step 2 Lubricate the new O-ring seal with clean engine oil and lay the seal on the fuel tank opening.
  18. Step 3 Install the sending unit/pump module in the tank and turn the lock ring clockwise using the fuel tank sending unit wrench.
  19. Step 4 Lift the fuel tank just enough to attach the fuel lines, vapor line and plug the pump module electrical connector.
  20. Step 5 Raise the fuel tank to set it in its mounting place and secure the tank straps using the ratchet, ratchet extension and socket.
  21. Step 6 Install the fuel tank shield using the ratchet, ratchet extension and socket, if you had to remove it.
  22. Step 7 Lower your Cadillac Deville.
  23. Step 8 Connect the ground, battery cable using the wrench.
  24. Build Fuel System Pressure
  25. Step 1 Plug the electrical connector located on the frame rail underneath the driver's side door.
  26. Step 2 Attach the splash shield to the frame rail using the ratchet and socket.
  27. Step 3 Turn the ignition key to the "On" position for three seconds to let the fuel system build pressure. Then turn the key to the "Off" position. Repeat the cycle three times to make sure the system has enough pressure.
  28. Step 4 Start the engine and check for fuel leaks.
Good luck and do rate this solution, please.

Mar 20, 2010 | Jaguar Vanden Plas Cars & Trucks

2 Answers

How do I replace the fuel pump on a F150 Ford truck and do i need any speical tools to do this


Things You'll Need:
  • Ratchet and socket
  • Wrench set
  • Floor jack and 2 jack stands
  • Ratchet extension
  • Fuel tank sending unit wrench number 310-123
  • Screwdriver
  • Slip joint pliers
  • New O-ring seal
  • Clean engine oil.
Steps to replace fuel pump:
  • Detach the splash shield from the frame rail located underneath the driver's side door. Use a ratchet and socket.
  • Unplug the electrical connector you will see after removing the splash shield. The connector leads to the fuel pump module.
  • Start the engine and let it idle until it stalls. Then crank the engine for about 5 seconds to relieve the remaining fuel pressure from the system. If the engine does not start due to a bad fuel pump, crank the engine to make sure fuel pressure is relieved.
  • Turn the ignition key to the Off position.
  • Disconnect the ground, battery cable from the battery using a wrench.
  • Jack up the rear of your F-150 using a floor jack and support it on 2 jack stands.
  • Remove the tank shield if your particular model is equipped with it using a ratchet, ratchet extension and socket.
  • Support the fuel tank with the floor jack.
  • Disconnect the straps holding the tank to the truck's body using the ratchet, ratchet extension and socket.
  • Lower the fuel tank just enough to gain access to the fuel lines, vapor lines and fuel pump electrical connector on top of the tank.
  • Disconnect the fuel lines and vapor lines from the sending unit/pump module. Press the lock tabs on the lines quick connectors and carefully pull the lines from their fittings. Then unplug the pump-module electrical connector.
  • Release the sending unit/pump module by turning the lock ring counterclockwise using the fuel tank sending unit wrench 310-123 or equivalent. See the Resources box and Tip boxes at the bottom of this article for more information.
  • Lift the sending unit/pump module off the tank carefully and discard the O-ring seal underneath the flange of the module.

    Install the Fuel Pump
  • Remove the old fuel pump from the module using a screwdriver and a pair of slip joint pliers and install the new pump on the module.
  • Lubricate the new O-ring seal with clean engine oil and lay the seal on the fuel tank opening.
  • Install the sending unit/pump module in the tank and turn the lock ring clockwise using the fuel tank sending unit wrench.
  • Lift the fuel tank just enough to attach the fuel lines, vapor line and plug the pump module electrical connector.
  • Raise the fuel tank to set it in its mounting place and secure the tank straps using the ratchet, ratchet extension and socket.
  • Install the fuel tank shield using the ratchet, ratchet extension and socket, if you had to remove it.
  • Lower your F-150..
  • Connect the ground, battery cable using the wrench.

Dec 05, 2009 | 2004 Ford F150

1 Answer

Do you have to drop the tank to change the fuel pump on 93 plymouth voyager or is there a way from the top?


Yes the tank must be removed

Fuel Pump: Service and Repair
WARNING: The fuel system is under constant pressure, even when the engine is OFF. Always release fuel pressure before servicing any fuel
system component.
FUEL PUMP REMOVAL
1. Release fuel system pressure.
2. Fuel tank must be removed prior to fuel pump service.
3. Using a hammer and a brass drift, carefully tap the fuel pump lock-ring counter-clockwise to release the fuel pump.
4. Remove the fuel pump and its O-ring from the fuel tank, and discard the old O-ring.
5. Cover tank openings to prevent dirt from entering system.
FUEL GAUGE SENDING UNIT REMOVAL
1. Gently bend the sending unit locking tabs away from the sending unit.
2. Remove the electrical connector cover (red). Remove the sending unit wires from the electrical connector.
3. Use one screwdriver to push on the fuel pump body, and use another to release the sending unit locking tab from the sending unit.
4. Slide the sending unit assembly off of the fuel pump reservoir housing.
5. Pull the wires through the reservoir body and fuel pump cover plate.
FUEL GAUGE SENDING UNIT INSTALLATION
1. Bend the sending unit wires and lay them into the slot on the back of the sending unit.
2. Slide the sending unit into the slots on the fuel pump reservoir body. Slide the wires through the triangle shaped hole in the fuel pump reservoir
body. Check that the tab in the fuel sending unit locks into the detent in the fuel pump reservoir body.
3. Slip the wires onto the tab of the fuel pump reservoir body.
4. Slide the sending unit wire terminals into the electrical connector. Install the terminal locking cover.
5. Slide the fuel sending unit electrical connector into the bottom of the fuel pump electrical connector. Check that the connectors are securely
attached and fully pushed into each other.
FUEL PUMP INSTALLATION
1. Wipe seal area of tank clean, and install a new O-ring seal on pump.
2. Position fuel pump module in tank and secure with the lock-ring.
3. Using a hammer and a brass drift, carefully tap the fuel pump lock-ring clockwise to lock the module in place.
NOTE: Do not overtighten the lock-ring, because the fuel pump seal could split and leak.
4. Install fuel tank assembly.
NOTE: ASD and fuel pump relays remain energized for 7 minutes during the following test, unless the test is stopped or the ignition switch is
turned to the OFF position.
5. Using scan tool, place ignition switch in "RUN" position and use Actuate Output Test "Auto Shutdown (ASD) Relay", to activate fuel pump and
pressurize system.
6. Check for leaks.

Sep 10, 2009 | 1993 Plymouth Voyager

1 Answer

Fuel sensor


  1. Release fuel system pressure.
  2. Fuel tank must be removed prior to fuel pump service.
  3. Using a hammer and a brass drift, carefully tap the fuel pump lock-ring counter-clockwise to release the fuel pump.
  4. Remove the fuel pump and its O-ring from the fuel tank, and discard the old O-ring.
  5. Cover tank openings to prevent dirt from entering system.


FUEL GAUGE SENDING UNIT REMOVAL

  1. Gently bend the sending unit locking tabs away from the sending unit.
  2. Remove the electrical connector cover (red). Remove the sending unit wires from the electrical connector.
  3. Use one screwdriver to push on the fuel pump body, and use another to release the sending unit locking tab from the sending unit.
  4. Slide the sending unit assembly off of the fuel pump reservoir housing.
  5. Pull the wires through the reservoir body and fuel pump cover plate.


FUEL GAUGE SENDING UNIT INSTALLATION

  1. Bend the sending unit wires and lay them into the slot on the back of the sending unit.
  2. Slide the sending unit into the slots on the fuel pump reservoir body. Slide the wires through the triangle shaped hole in the fuel pump reservoir body. Check that the tab in the fuel sending unit locks into the detent in the fuel pump reservoir body.
  3. Slip the wires onto the tab of the fuel pump reservoir body.
  4. Slide the sending unit wire terminals into the electrical connector. Install the terminal locking cover.
  5. Slide the fuel sending unit electrical connector into the bottom of the fuel pump electrical connector. Check that the connectors are securely attached and fully pushed into each other.
FUEL PUMP INSTALLATION

  1. Wipe seal area of tank clean, and install a new O-ring seal on pump.
  2. Position fuel pump module in tank and secure with the lock-ring.
  3. Using a hammer and a brass drift, carefully tap the fuel pump lock-ring clockwise to lock the module in place. NOTE: Do not overtighten the lock-ring, because the fuel pump seal could split and leak.
  4. Install fuel tank assembly. NOTE: ASD and fuel pump relays remain energized for 7 minutes during the following test, unless the test is stopped or the ignition switch is turned to the OFF position.
  5. Using scan tool, place ignition switch in "RUN" position and use Actuate Output Test "Auto Shutdown (ASD) Relay", to activate fuel pump and pressurize system.
  6. Check for leaks.

Nov 07, 2008 | 1999 Dodge Caravan

1 Answer

2001 Nissan Xterra


Most likely corrosion on the sending unit connector. If corroded will need sending unit assembly. To check lift up passenger side rear seat cushion and remove the top and bottom plates, fuel tank sender is right below.

Aug 23, 2008 | 2001 Nissan Xterra

Not finding what you are looking for?
1993 Plymouth Voyager Logo

Related Topics:

27 people viewed this question

Ask a Question

Usually answered in minutes!

Top Plymouth Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Plymouth Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...