Question about Buick LeSabre

2 Answers

My '05 LeSabre warning light for check tire pressure came on. I checked all 4 tires and they each have 32# of pressure. How do I reset the monitor? No manual in the car. Thanks

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 379 Answers

Make sure your spare is up to 32#'s pressure also , unless its one of the donut tires, turn ignition switch to on with engine off , press and hold GUAGE INFO button which is located to the left of the sterring column until TIRE PRESSURE messgage is displayed , press and hold RESET BUTTON for 5 seconds , TIRE PRESSURE RESET message should appear on display , release RESET button, a TIRE PRESSURE NORMAL message should appear on the display , after ressetting the Tire Pressure Monitor system it requires 30 minutes of straight driving to complete calibration process .

J5


Posted on Jan 14, 2009

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 10 Answers

Have it checked out

Posted on Jan 14, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My ( ! ) light stays on


Hi there:
Is your TPMS Warning Light On? The Tire Pressure Monitor System monitors the inflation pressure of the tires on your vehicle. If the pressure inside any tire drops 25 percent or more below its recommended inflation pressure, the warning light comes on to alert you.


Should you stop driving and check your tires immediately? It would probably be wise to find a safe place to stop or pull over so you can check the tires. You may just have a low tire that has been slowly seeping air over a period of time. Or, you may have a tire that is going flat. The TPMS Warning Light only tells you the pressure is low in one of the tires, not how fast the tire is losing pressure.


Important: Check the pressure in ALL of your tires, not just the one that triggered the TPMS Warning Light. Why? Because you may have other tires that are also low, but not low enough to trigger the warning light.
If you discover that one or more tires are low, add air to bring them back up to the recommended inflation pressure for your vehicle. You can find this information on a decal which may be mounted in a door pillar, the glovebox, or in your owners manual (which you should carry in your glove box).


5_26_2012_5_47_59_pm.jpg


Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

May 26, 2012 | Holden Vectra Cars & Trucks

1 Answer

Tyre pressure warning light showing when pressures are correct


Hi, the tire pressure monitor detects any changes in the tire inflation pressure. Therefore, it must initialize and store it in its memory if the tires or wheels have been replaced, re-inflated or the tires have been rotated. You can re-initialize the system by following these steps:

1. Check and make sure that your tires are inflated to the correct pressure

2. Turn the ignition switch to the ON position. If the low tire pressure warning light comes on, push and hold the tire pressure warning reset switch (in the glove box) until the warning light turns off and then release the switch.

3. Now press and hold the tire pressure warning reset switch until the low tire pressure warning light blinks three times.

4. Initialization is *not* completed until driving at the vehicle speed of 19 mph or over for more than one hour. the tire pressure monitoring starts when initialization is completed.

May 13, 2011 | Renault 18I Cars & Trucks

1 Answer

My 2008 highlander 4wd tire pressure warning light just went on. Checked tire pressure on all 4 mounted tires found to have 25-26 psi. Inflated it to 30 psi (recommended) and look for the reset button...


turn the key to the on position (not running)
let at least 6 lbs of air out of each tire
put at least 32 lbs of air back in each tire
turn ignition to off
start vehicle and the light and sensors should be reset

Dec 09, 2010 | Toyota Highlander Cars & Trucks

4 Answers

Tire warning light won't go off - Tires are correct pressure


it needs to be reset, here is the procedure>>>http://library.motoralldata.com/techRef/WebHelp/Tire_Pressure_Monitor_Reset_Procedures/Toyota/2005-2006_Solara.htm

Aug 10, 2010 | 2006 Toyota Solara

1 Answer

Tire warning light will not go out


Check the spare tire pressure and make sure it's 32 PSI.

Fix-A-Flat emergency air can will destroy the first generation sensor.

Tire shop will has Tire-pressure monitoring system (TPMS) reset hand held unit to reset the monitoring system.

Dec 11, 2009 | 2008 Mazda MAZDA6

1 Answer

Changed right front tire now reads zero on dash light is on


Your tire pressure monitor needs to be reset whenever you change or rotate your tires...

1. check and make sure that your tires are inflated to the correct pressure

2. turn the ignition switch to the ON position. If the low tire pressure warning light comes on, push and hold the tire pressure warning reset switch (think the switch is in the glovebox, but not sure) until the warning light turns off and then release the switch.

3. now press and hold the tire pressure warning reset switch until the low tire pressure warning light blinks three times.

4. initialization is *not* completed until driving at the vehicle speed of 19 mph or over for more than one hour. the tire pressure monitoring starts when initialization is completed.

Aug 24, 2009 | 2008 Chevrolet Tahoe

3 Answers

My ABS light is coming on what does that mean?


1. check and make sure that your tires are inflated to the correct pressure

2. turn the ignition switch to the ON position. If the low tire pressure warning light comes on, push and hold the tire pressure warning reset switch (think the switch is in the glovebox, but not sure) until the warning light turns off and then release the switch.

3. now press and hold the tire pressure warning reset switch until the low tire pressure warning light blinks three times.

4. initialization is *not* completed until driving at the vehicle speed of 19 mph or over for more than one hour. the tire pressure monitoring starts when initialization is completed.



As for the ABS light, that means your antilock brake system has detected an issue such as a block sensor, or a faulty relay, etc.. when this light is on, it means that your abs may not engage when it should, or may engage when it shouldn't.

Aug 21, 2009 | 2003 Ford Expedition

1 Answer

How do you reset low tire light


1. check and make sure that your tires are inflated to the correct pressure

2. turn the ignition switch to the ON position. If the low tire pressure warning light comes on, push and hold the tire pressure warning reset switch (think the switch is in the glovebox, but not sure) until the warning light turns off and then release the switch.

3. now press and hold the tire pressure warning reset switch until the low tire pressure warning light blinks three times.

4. initialization is *not* completed until driving at the vehicle speed of 19 mph or over for more than one hour. the tire pressure monitoring starts when initialization is completed.

Aug 20, 2009 | 2005 Chrysler PT Cruiser

3 Answers

The check tire pressure light and ABS auto traction sensor light keep coming on. Tire pressure is good


The tire pressure monitor detects any changes in the tire inflation pressure. Therefore, it must initialize and store it in its memory if the tires or wheels have been replaced, re-inflated or the tires have been rotated. You should be able to re-initialize the system by following these steps:

1. check and make sure that your tires are inflated to the correct pressure

2. turn the ignition switch to the ON position. If the low tire pressure warning light comes on, push and hold the tire pressure warning reset switch (think the switch is in the glovebox, but not sure) until the warning light turns off and then release the switch.

3. now press and hold the tire pressure warning reset switch until the low tire pressure warning light blinks three times.

4. initialization is *not* completed until driving at the vehicle speed of 19 mph or over for more than one hour. the tire pressure monitoring starts when initialization is completed.

Aug 11, 2009 | 2004 Cadillac Deville

1 Answer

Tire pressure monitor


32 psiis actually low for a 3500. I have a 1500 silverado that runs 44 psi cold. The tire inflation monitor , monitors inflated cirunference. Sooooo, If it isn'nt round enough, it will let you know. Driving warms up both the air and the tire,off course changing everything again. Pressure is up and tire is bigger. Ask me not how it can tell what is going on with the tire sitting still. I'm only on page 9,000, the answer is here somewher. :-) Well good luck. I do know the above is accurate._Ned_

Jun 26, 2008 | 2004 Chevrolet Silverado 3500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

691 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

60792 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...