Question about 1992 Subaru Legacy

1 Answer

Temp gauge wont stop reading hot and dash lights flicker

Where do i go to get a wiring diagram to find out were all the earths are in my 1992 rs liberty my car is not over heating

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 46 Answers

90% of the time the reason for this is because there are air bubbles in the cooling system. You just have to bleed the system and you will be fine

Posted on Jan 14, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I had my Alternator changed yesterday on a Ford escort gti. The battery light was on and temp gauge was stuck past hot. Once changed all was fine but today I started it up and temp gauge is stuck past hot...


The temp gauge and battery light issues may not have been related.
The gauge reads high when the circuit to the temp sending unit is grounded. It could be the gauge on the dash, or a wiring problem, or the temp sending unit on the engine.

Jun 20, 2013 | Cars & Trucks

2 Answers

Gas gauge and temp gauge and heater/ac fan dont work


Sounds like a fuse or an earth wire loose in the cabin. Take the fuses out and chk them in the light. Go thru all earth wires both in and outside the cabin, something is loose if not a fuse, remember fuses in the engine bay. cheers

Sep 04, 2012 | Cars & Trucks

1 Answer

Wiring diagram 2006 fordranger diesel pickup


Hi , there will be 3/4 wires at the fuel tank gauge. 1 ground wire ,1 gauge(on dash) wire, 1 gauge low level indicator light (warning on dash) Get a test lamp , ground test lamp and probe each wire. 1 will do nothing (earth wire) 1 will bring on dash low fuel light , the other will be the gauge on the dash which will rise (slowly) to the full position.

Jan 05, 2012 | 2005 Ford Ranger

1 Answer

My truck started running poorly as the temp outside has gotten colder. It runsmeans poorly tillas operating temp. Then atu opp temp Iit trys to die at stop lights. I had replace plugs/wires/ fuel...


You have a Cold starting sequence that is similar to a choke. This system relies on getting a temperature signal back to the Computer. It should have at least 1 water sensor. Sometimes there are 2 sensors with one working the dash gauge and the other working the Cold start sequence. If you find 2 sensors just unplug 1 at a time and do this when the engine temperature has been rising. When you find the dash gauge sensor you will lose the reading on the dash gauge when it is unplugged. The remaining sensor would control the Cold start sequence, so replace that sensor.

Dec 04, 2011 | 1992 GMC Sierra K1500

3 Answers

I Have a 1992 dodge dakota And my temp gauge does not move. Do you know whats wrong with it


find temp sender turn key on and disconect wire from sender and earth it if guage moves to hot sender falty, if not guage faulty, or broken wire,or no power to guage

Aug 14, 2011 | 1992 Dodge Dakota

1 Answer

Have a 1992 chevy 2500 half the cluster lights go out aswell the fuel pessure reads zero and the temp max reading. whent the lights are out or the dimmer is turned off the gauges work properly but as soon...


It sounds like a bad ground. Check the ground circuits to your dash lights as well as check out your tail lights to make sure they are working properly. (The tail lights run on the same circuit as the dash lights, although tey have a separate grounding point.) The gauges are most likely going goofy because the dash and/or tail lights are trying to pull ground through the gauges circuit.

Nov 30, 2010 | 1992 Chevrolet C1500

1 Answer

Fuel gauge/temp gauge not working


There are two sensors, one for ECU temp. readings with two pin connector and other one with only one wire, which has been probably disconnected when you replaced the CPC solenoid - very close position.

May 31, 2009 | 1992 Subaru Legacy

1 Answer

Temperature Guage, '89 Camry


the cable going from the gauge to the sender unit is an earth return. if you take it off the sender unit wire if the gauge does read hot the sender and earth it out the gauge should go to the hot segment.dont leave this cable to earth very long do it quickly. if the gauge does read it is ok, there is no earth to the petrol tank. if it does not read it will be faulty. hope this helps.

Apr 24, 2009 | 1989 Toyota Camry

1 Answer

1992 toyota Corolla Temp gauge does not work


find the wire that goes to temp sender and apply earth to it turn ignition on the temp gauge should read hot if it does replace water temp sender if gauge dose not move gauge needs replaging

Jan 26, 2009 | 1992 Toyota Corolla

Not finding what you are looking for?
1992 Subaru Legacy Logo

166 people viewed this question

Ask a Question

Usually answered in minutes!

Top Subaru Experts

yadayada
yadayada

Level 3 Expert

63291 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Subaru Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...