Question about Hyundai Motor 1999 Elantra

1 Answer

What is the cost to fix an idle control motor?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sniper:

    An expert who has posted more than 50 answers, of which 90% or more were rated as helpful.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 52 Answers

The cost to change this out is very cheap, it takes only a few mins as there are only two bots and an electrical connector but they might charge you min of an hr,the cost of the valve for a typical car is around 50- 80 dollars.
hope this elps
simfea@telus.net

Posted on Jan 15, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you fix an idleing problem on b2300 mazda truck?


What kind of idling problem ? An what year Mazda ? Idle is controlled by the engine computer via a IAC motor , idle air control valve or motor, what ever Mazda calls there set up ! Or if a fairly new vehicle, they use drive by wire or electronic throttle control . With the idle air control set up passages get plugged an don't allow enough air to by pass the throttle plate causing stalling problems . A vacuum leak can cause a ruff unstable idle an stalling also . A dirty throttle plate can cause idle problems as well ! A scan tool ,not a code reader is a very use full tool to check engine data parameters. With the scan tool you can view idle air control counts . To see if the engine computer is actually controlling the idle air control valve . Idle Air Control Valve

Also an engine misfire can cause idle problems , also clogged fuel injectors can as well . A good diagnostic technician would start with hooking up a professional grade scan tool , checking for DTC'S - diagnostic trouble codes , misfire data , engine sensor data , IAC counts ! Section 20 Idle Speed Controls lecture preview

Oct 02, 2015 | Mazda Cars & Trucks

1 Answer

On a dodge neon 2004 the code reads P0507 idle control system. Is that a sensor?


No, it's not a sensor. The engine computer controls idle speed by an "actuator" called an IAC -idle air control -motor or valve. It sits right on the throttle body where the air hose, the big boot, connects to the top of the engine. It controls the idle air passage-smaller air passages besides the larger throttle plate opening- according to computer command.
Probably your IAC motor or valve has a problem. A good cleaning often helps. Remove it and scrape off gently the deposits. Don't push the end piece, the pintle, back and forth, and don't spray cleaner up towards the little motor. Check the air passages where it mounts on the throttle body and clean as best you can. If it needed cleaning, take off the big boot and use a sensor safe cleaner, like throttle body cleaner, and old rags and old toothbrushes, and clean out the inside of the throttle body and the big butterfly valve, the throttle valve, inside. Note that when it is at rest, no gas pedal giving it gas, the throttle valve is almost completely closed. Those separate air passages in your idle control system, what the IAC motor controls, is the only way for the engine to get enough air to keep running. If they clog up, or the valve or motor doesn't work anymore, anyway the computer sees a wrong result from engine rpm sensors, and what it is commanding from the IAC motor, so it alerts you the problem is in the...in the idle cntrl system. Have at it, friend. It's either do it yourself or pay labor costs for a pro.

May 05, 2015 | 2004 Dodge Neon

1 Answer

High idle replaced cat and o2 sensor also pvc and tube?


i had a high idle problem on my Chevy blazer.there is a air mix censer that controls the idle,it cost a $100.00.I changed it and fixed my problem.IBOUGHT A SHOP MANUAL AND IT TOLD ME ABOUT THE IDLE CONTROL CENSER!

Oct 30, 2012 | Cars & Trucks

1 Answer

Just started idling rough, sometimes stalling


Shot in the dark here without knowing the vehicle but it could be an Idle Air Control valve starting to fail. An IAC (idle air control) motor is designed to adjust the engine idle RPM speed by opening and closing an air bypass passage inside the throttle body. The cars computer or PCM (powertrain control module) receives information from various sensors and will output signals to adjust the idle air control motor in or out to adjust engine idle speed by controlling engine idle air. An idle air control motor can fail one of two ways, either the motor short circuits and stops working or the motor will develop high resistance and cause the idle air control motor to react slowly, either failure can cause the engine to stall at idle. When a trouble code scan is performed it sometimes won't always detect a failed or weak idle air control motor. To check the idle air control motor remove the unit, with the wires connected turn the key to the "on" position without starting the engine, the idle air control should move in or out. If the idle air control motor does nothing it has probably failed, replace it with a new unit and recheck system. Note: while the idle air control motor is removed clean (use aerosol carburetor cleaner) the passages the idle air control uses to control idle air speed, also inspect the idle air control for a build-up on the seating (pointed) end and clean as necessary.

Jul 20, 2011 | Mazda B2300 Cars & Trucks

1 Answer

I have a 2004 Hyundai Getz which is idling very fast, I have been told that it needs motor which controls the idling speed and the total cost in Australia will be about. $420.00, this seems a lot to fix...


You can use a throttle body cleaning that might help, thoses control motor has a jack screw and it time it wears out and can no longer operate try using a throttle body cleaner they do work some times

Apr 21, 2011 | Hyundai Accent Cars & Trucks

1 Answer

2002 doge neon r/t revs itself when i start it


The most common source of that problem is a sticking idle control motor. As a first step, purchase a new gasket and/or O-ring for the idle control motor. Remove the motor and clean it out using aerosol carburetor cleaner. If the idle control motor was sticking, that should cure it. It the fix only lasts temporarily, you need to replace the idle control motor. This is a common problem with vehicles with over 80,000 miles on them.
Charlie

Jun 18, 2009 | 2002 Dodge Neon

1 Answer

I have a 89 bronco with efi that high edle when warm how do i fix this problem


Either your idle air control motor is sticking open OR you have a vacuum leak somewhere on the engine. First try removing the idle air control motor and cleaning it with aerosol carburetor cleaner. Reinstall it using a new gasket. See if that fixes it. It may fix it or the fix may only last a few days or a week. If the fix lasts a short time, you need a new control motor ($100) If a new idle control motor does not fix it, then you have to search for a vacuum leak (leaking rubber hose, leaking fuel pressure regulator, leaking power brake booster, etc) Charlie

Jun 14, 2009 | 1987 Ford Mustang

2 Answers

I have a 1993 honda civic 1.5


did you get your battier check???

Feb 26, 2009 | 1993 Honda Civic 4 Door

1 Answer

Hyundai lantra


The baseline idle is set too high.  Meaning someone has screwed the idle screw out too far.  Probably because the Idle Speed Control Motor is dead.  Same thing happened to me on the same model car. Replacing the ISC Motor is extremely easy to do, a replacement cost me $135AU.

Aug 24, 2008 | 1993 Hyundai Elantra

Not finding what you are looking for?
Hyundai Motor 1999 Elantra Logo

Related Topics:

55 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

69199 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22026 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6817 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...