Question about 1996 Chevrolet Blazer

3 Answers

4 wheel drive not working

I have a 96 chevrolet blazer and my four wheel drive will not work. i looked under the vehicle and the front driveshaft from the transfer case to the front axles is moving when you engage the four wheel drive but front axles don't seem to lock in. i replaced a vacuum piece located under the battery but still doesn't seem to work.

Posted by on

  • Anonymous Mar 17, 2014

    my four wheel drive dose not work i had change the senor in the front and still dose not work is there one in the back to or what else can it be

×

3 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

When you engage it in 4 wheel make sure you are getting vacuum to the acuator just pull the hose off and feel to see if there is vacuum if not check all vacuum hoses

Posted on Jan 25, 2009

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

I just replaced the actuator in my 96 Blazer and the 4WD works perfectly! I use this vehicle to deliver mail and I'm grateful it was only a $30 part. Check to make sure all the hoses are connected at the other end of the actuator since you've already replaced that. Good Luck!

Posted on Jan 15, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 2,920 Answers

Theransfer case may not be fully engaging

Posted on Jan 14, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1996 K 1500 with manuel four wheel floor shift will work in four low but will not work in four high (what could be the problem). Dan


so the front driveshaft turns in 4 low? or you just feeling gear reduction in 4 low?if the front drive shaft will not turn in 4 or 4low then suspect a shift fork broken. when i say turn i mean under engine power.

Sep 30, 2010 | 1996 Chevrolet K1500

1 Answer

How do you remove the starter from 2000 blazer


raise the front of vehicle & support on jackstands.It will help to take off the (left wheel on2.2L models,right wheel on 4.3L models)Remove skid plate(if equipped)On 2.2 models remove front driveshaft.On some early models,it may be necessary to raise the engine/transmission with a floorjack an under the transmission and remove the transmission crossmember for access to the starter motor bolts.On models so equipped ,remove the starter heat shield.From under the vehicle, disconnect the solenoid wire and battery cables from the terminals on the solenoid.Remove the starter mounting bolts, and then remove starter motor (note location of shims)

Jul 19, 2010 | 2000 Chevrolet Blazer

1 Answer

2000 silverado 4x4 not working


sound like the electronic actuators are not working properly,get your test light out

Apr 15, 2010 | 2000 Chevrolet Silverado

2 Answers

NEED TIRES


You can easily tell if you have 4wd by looking under the suv to see if there is a transfer case o nthe rear of the transmission as well as a driveshaft going to a front axle.

Mar 16, 2010 | 2003 Ford Expedition

1 Answer

Chevy blazer runs funny in 4 wheel drive


Hello,
Be sure that the joints on your front driveshaft are in good condition, hope this helps, good luck

Apr 03, 2009 | 1998 Chevrolet Blazer

1 Answer

1999 Chevy Blazer makes noise


Check your driveshaft universal joint (u joint). When the needle bearings go, this is the sound it makes. To check, chock all wheels front and rear, put in neutral, if 4x4, put 4x4 in neutral also, go under vehicle, grab driveshaft at u joint and try to turn back and forth, watching for play, wobble in u joint. U should be able to see it. Let me know how u do.

Mar 21, 2009 | 1999 Chevrolet Blazer

1 Answer

95 blazer 4x4 4 wheel drive not working


There is a vacuum actuator mounted on the front differential that locks the shafts to engage four wheel drive.

Jan 28, 2009 | 1995 Chevrolet Blazer

4 Answers

96 chevey blazer 4x4


Sounds like the front axle electric actuator is bad. these are mounted on the front differential housing. they are known to go bad.

Nov 02, 2008 | 1996 Chevrolet Blazer

1 Answer

Stuck in two wheel drive. I changed my front wheel bearing the four wheel drive went out. The four wheel drive lights on dash blink then go out. Service 4 wheel drive comes on. Is there a servo that...


There is an electric motor that engages drive.  Mine was stuck and a mechanic beat it w a hammer while I was in vehicle w brake on in drive pushing the diff 4wd buttons.  It freed up and started working fine!!  It looks like a small starter under car on passenger side. Or buy one on ebay  for cheap and replace it

Jul 21, 2008 | 2000 Chevrolet Blazer

Not finding what you are looking for?
1996 Chevrolet Blazer Logo

778 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

63990 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...