Question about 2005 Chrysler Sebring Conv

1 Answer

Windshield wiper spray hose disconnected

How do I reconnect the hose for the windshield wiper spray with all of the foam insulation that covers the underside of the hood? I know the hose is disconnected and not clogged.

Thanks ahead of time!

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 599 Answers

Razor blade ...carefully.......... 3m weatherstripping adhesive (gorilla snot) to re secure....good luck

Posted on Jan 13, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do you replace windshield wiper motor on a 1997 ford e250 van


REMOVAL
  1. Raise and support the hood.
  2. Remove the windshield wiper pivot arms.
  3. Remove the cowl top vent panels.

25287270-15uk5heqgoha5mc4ejw3dmql-1-0.gif
  1. Disconnect the windshield wiper mounting arm and pivot shaft.
  1. Remove the access cover from the dash panel.
  2. Remove the mounting arm and pivot shaft retaining clip.
  3. Disconnect the windshield wiper mounting arm and pivot shaft from the windshield wiper motor.

25287270-15uk5heqgoha5mc4ejw3dmql-1-2.gif
  1. Remove the windshield wiper motor.
  1. Disconnect the electrical connector.
  2. Remove the three bolts.
  3. Remove the windshield wiper motor.
INSTALLATION

25287270-15uk5heqgoha5mc4ejw3dmql-1-5.gif
  1. Install the mounting arm and pivot shaft retaining clip on the windshield wiper mounting arm and pivot shaft.

25287270-15uk5heqgoha5mc4ejw3dmql-1-9.gif
  1. Install the windshield wiper motor.
  1. Place the windshield wiper motor in the dash panel.
  2. Install the three retaining bolts.
  3. Reconnect the electrical connector.

25287270-15uk5heqgoha5mc4ejw3dmql-1-14.gif
  1. Reconnect the windshield wiper mounting arm and pivot shaft.
  1. Press on the windshield wiper mounting arm and pivot shaft after it is aligned with the windshield wiper motor.
  2. Install the access cover in the dash panel.
  1. Install the cowl top vent panels.
  2. Install the windshield wiper pivot arms.
  3. Adjust the windshield wiper pivot arms.
This is technically for the V6 4.2L but I'm sure those Ford E250's have the same setup for windshield wiper motor. Let me know how it goes.

Nov 17, 2014 | Cars & Trucks

2 Answers

Windshield wipers won't work after removing battery to get to the windshield wiper pump that squirts fluid to clean windshield


Sometimes disconnecting the battery does more damage then you want it might have trip a fuse or relay check those if thats not it, maybe wiper motor or transmission went out.

Nov 30, 2012 | 2005 Saturn VUE

1 Answer

How to replace the wiper motor on a 1994 volkswagon golf


The wiper motor on a Volkswagen is an electric motor connected through a drive linkage to the wiper arms. Windshield wipers are an integral feature for operating a motor vehicle safely. If your wipers are not functioning, or seem to lack the speed or power they used to have, the wiper motor should be removed and replaced immediately
.


Location
  • The wiper motor on a Volkswagen is located directly underneath the plastic cowl cover. The cowl cover is located directly below the windshield.

Removal
  • Begin by removing the wiper arms by prying off the covers at the base of the arms and removing the nuts that secure the arms to the drive shafts. Label the passenger and driver arms so they can be installed in the same positions. They are not interchangeable. Remove the rubber hood to cowl weather seal. Unscrew the plastic fasteners from the driver's side of the cowl cover, then remove this half of the cover. Remove the fasteners from the passenger's side cowl cover and remove this half of the cover. Disconnect the windshield wiper motor wiring harness by separating the plastic wiring connector. Remove the three bolts that secure the wiper motor to the vehicle's body. Pull the motor slightly away from the body, then remove the nut that connects the motor shaft to wiper linkage. Remove the motor.

Installation
  • Place the new wiper motor into position in the cowl and reconnect it to the wiper arm linkage. Then reinstall the three retaining bolts. Reconnect the plastic wiring connector to the wiper motor wiring harness. Place the cowl covers into position below the windshield and reinstall the plastic fasteners that retain them. Reinstall the rubber hood to the cowl weather seal. Reinstall the wiper arms in the same position you removed them from, along with the wiper arm retaining nuts and lower wiper arm covers. Turn the windshield wipers on and test for proper operation. If the wiper blades slap against the bodywork surrounding the windshield, loosen the nuts that connect the wiper arms to the shafts and adjust.

More Read: OBD2 car diagnostic tool

Aug 06, 2012 | 1994 Volkswagen Golf

1 Answer

Where is the windshield washer motor located? Is it near the heater motor? I had mine fixed and now the heat comes out of the dash for the defroster


Windshield Washer Pump Removal & Installation To Remove:
  1. Remove the air cleaner assembly.
  2. Remove the bolts. windwash.gif

  3. Position the pump and reservoir aside.
  4. Disconnect the electrical connectors.
  5. Disconnect the washer hose.
  6. Remove the pump and reservoir.
  7. Remove the washer pump.
washpump.gif

WARNING
Windshield washer solution contains methanol which is poisonous. Observe all cautions and warnings indicated on label of washer solution container.
NOTE: Windshield washer fluid should be collected in a container after the windshield washer hose is disconnected.
To Install:
WARNING
Windshield washer solution contains methanol which is poisonous. Observe all cautions and warnings indicated on label of washer solution container.
  1. Install washer pump in reservoir.
  2. Install washer pump reservoir assembly.
  3. Connect washer hose.
  4. Connect washer electrical connector.
  5. Install air cleaner assembly.
---
The windshield wiper fluid pump is located in the tank which is not in the heater motor or defroster area in the dash.

The defroster/heat control door is located in the dash board area:

Air Door Actuators, Cables or Motors Removal & Installation Air Inlet Door Vacuum Control Motor To Remove:
  1. Remove the instrument panel lower insulator cover.
  2. Disconnect the vacuum connector.
  3. Remove the control arm clip and the spring.
  4. Remove the nuts and the air inlet door vacuum control motor.
Air inlet door vacuum motor mounting screws for-10-00-245.gif

To Install:
  1. Install the vacuum motor on the mounting bracket.
  2. Connect the control arm and spring.
  3. Connect the vacuum hose to the vacuum motor.
  4. Install the lower instrument panel lower cover.
Floor Defrost Door Vacuum Control Motor To Remove:
  1. Disconnect the negative battery cable.
  2. Remove the left lower dash insulator panel and disconnect the lamp.
  3. Remove the two pin-type retainers and remove the fill panel.
  4. Remove the DLC mounting screws.
  5. Detach the vacuum line.
  6. Remove the lighting module.
  7. Remove the screws and the bracket.
  8. Remove the floor/defrost door vacuum control motor.
Floor/Defrost vacuum motor mounting screws for-10-00-246.gif

To Install:
  1. Connect the vacuum lines and install the floor/defrost vacuum motor.
  2. Install the bracket and lighting control module.
  3. Install the DLC bracket and mounting screws.
  4. Install the fill panel.
  5. Install the left lower dash insulator panel.
  6. Connect the negative battery cable.
Panel Door Vacuum Control Motor To Remove:
  1. Remove the instrument panel.
  2. Reach through the door opening and remove the pin.
  3. Disconnect the panel door vacuum control motor vacuum line.
  4. Remove the screws and remove the panel door vacuum control motor.
To Install:
  1. Install the panel door vacuum motor.
  2. Connect the vacuum line to the panel door motor.
  3. Reach through the opening and install the pin to the linkage.
  4. Install the instrument panel.
prev.gif next.gif

Jan 19, 2011 | 2003 Mercury Grand Marquis

1 Answer

How to reconnect the hose on my windshield wipers to spray windshield washer fluid correctly


is this the type that runs through the hood and the hole is so small you can run a piece or wire thread like a needle and tape or tie to hose or are they just pulled apart

Dec 30, 2010 | 1995 Pontiac Grand Am

1 Answer

I have a 2008 Grand Prix. Windshield washer is


follow the hoses to the hood or wiper arm (i dont know where your spray nozzles are)and disconnect hem and press the spray button. if it sprays your nozzles are plugged, if not its your pump motor.

Feb 16, 2010 | 2008 Pontiac Grand Prix

1 Answer

The wiper motor on my 1983 Ford Ranger still works but the wipers no longer move. I think there is a failure of the mechanical linkage. Where do I go to find repair parts?


why do you think the motor still works if the wipers don't move? Can you hear the motor run or can you see a little movement when you turn the switch on?

What happens when you activate the washers?

go to a salvage yard that allows you to remove the parts yourself. Then you can see how the motor and linkage assembly comes out.


don't have 1983 info, but here is 1994:

Section 01-16A: Wiper and Washer System, Ranger/Explorer 1994 Ranger and Explorer Vehicles Workshop Manual
DESCRIPTION AND OPERATION Windshield Wiper System, Ranger/Explorer The windshield wipers are actuated by a permanent magnet, rotary-type electric windshield wiper motor (17504) . The two windshield wiper pivot arms (17526) and windshield wiper blades (17528) are mounted on a pivot shaft, one at each side of the windshield. The windshield wiper mounting arm and pivot shaft (17566) are connected to the motor by windshield wiper adapter and connecting arm clip (17531) . Ranger and Explorer vehicles are equipped with an interval wiper and washer (IWW) system featuring a lever-type turn signal and windshield wiper switch (13K359) mounted on the steering column. The IWW windshield wiper governor (17C476) uses a relay contact to control current to the windshield wiper motor . The governor electronic circuitry controls the contact to supply current to windshield wiper motor . A rear wiper/washer system is available on Explorer vehicles. The rear window wiper system consists of a windshield wiper motor mounted inside the liftgate (40010) , an articulating windshield wiper pivot arm and windshield wiper blade , a windshield wiper/washer switch (17A553) and an inline circuit breaker. The front electric windshield washer system consists of a control switch, integral with the turn signal, a windshield washer reservoir (17618) and windshield wiper motor and the necessary windshield washer hoses (17A605) , windshield washer nozzle jet and brackets (17603) and attaching parts.
------------------------------------------------------------------------------------------------
Pivot Shafts and Linkage Removal and Installation
NOTE: The left and right pivot and windshield wiper adapter and connecting arm clip assemblies are serviced separately.
  1. Perform Steps 1 through 9 of Windshield Wiper Motor Removal as described in this section.
  1. If servicing left windshield wiper adapter and connecting arm clip , remove left windshield wiper mounting arm and pivot shaft and windshield wiper blade assembly.
  1. Remove left windshield wiper adapter and connecting arm clip access cover.
  1. Remove left pivot nut, lower windshield wiper adapter and connecting arm clip and slide it out through left access opening. For installation, follow removal procedures in reverse order. Tighten nut to 10-13 Nm (7-10 ft-lb). Make sure the clip is fully seated in the windshield wiper adapter and connecting arm clip . Do not try to install clip with windshield wiper adapter and connecting arm clip on motor crank pin.
----------------------------------------------------------
Windshield Wiper Motor Windshield wiper motor are not serviceable. If worn or damaged, the windshield wiper motor must be replaced as an assembly. Removal
  1. Cycle windshield wiper blades until in straight-up position and turn ignition switch OFF.
  1. Disconnect battery and wiper motor electrical connector.
  1. Remove the right windshield wiper mounting arm and pivot shaft and windshield wiper blade .
  1. Disconnect the battery ground cable (14301).
  1. Remove the right pivot nut and allow the windshield wiper adapter and connecting arm clip to drop into the cowl top outer panel .
  1. Remove the linkage access cover, located on the right side of the dash panel near the windshield wiper motor.
  1. Reach through the access cover opening and unsnap the wiper motor clip.
  1. Push the clip away from the windshield wiper adapter and connecting arm clip until it clears the nib on the crack pin. Then, push the clip off the windshield wiper adapter and connecting arm clip.
  1. Remove the windshield wiper adapter and connecting arm clip from windshield wiper motor crank pin.
  1. Remove nut and ground strap.
  1. Remove three attaching nuts from windshield wiper motor. Remove the windshield wiper motor .
Installation
  1. Position the windshield wiper motor and install the three attaching screws. Tighten to 13.6-19.0 Nm (10-14 ft-lb).
  1. Install nut and ground strap.
  1. Connect wiper motor electrical connector.
  1. Install clip completely onto right windshield wiper adapter and connecting arm clip. Make sure the clip is fully seated. Do not put the windshield wiper adapter and connecting arm clip on the motor crank pin and then try to install the clip.
  1. Install the left windshield wiper adapter and connecting arm clip onto the wiper motor crank pin.
  1. Install the right windshield wiper adapter and connecting arm clip onto the wiper motor crank pin. Pull the windshield wiper adapter and connecting arm clip onto the crank pin until it snaps into place. The clip is properly installed if the nib is protruding through the center of the clip.
  1. Install the right windshield wiper mounting arm and pivot shaft and nut. Tighten the nut to 9.5-12.5 Nm (84-110 in-lb). NOTE: When the battery has been disconnected and reconnected, some abnormal drive symptoms may occur while the powertrain control module (PCM) (12A650) relearns its adaptive strategy. The vehicle may need to be driven 10 miles or more to relearn the strategy.
  1. Connect the battery ground cable and turn the ignition switch on. Turn turn signal and windshield wiper switch off so windshield wiper motor will park, then turn ignition switch off. Replace right windshield wiper adapter and connecting arm clip access cover.
  1. Install the windshield wiper mounting arm and pivot shaft and windshield wiper blade assemblies on the pivot shafts to dimension X. Dimension X is the distance between the centerline of the blade saddle and the top edge of the cowl top outer panel grille. The value of Dimension X for each vehicle is given in the Dimension X chart in the Specifications portion of this section.
  1. Test the system.
6bd608c.gif

Jan 04, 2010 | 1983 Ford Ranger

1 Answer

Wiper motor replacement


SECTION 501-16: Wipers and Washers 1999 Town Car Workshop Manual REMOVAL AND INSTALLATION Mounting Arm and Pivot Shaft Removal
  1. Disconnect the battery ground cable (14301).
  1. Remove the windshield wiper pivot arms (17527).
    1. Remove the nuts (one each side).
    1. Remove the windshield wiper pivot arms.
  1. Remove the LH and RH cowl top vent panels.
    1. Remove the hood weatherstrip.
    1. Remove the screws.
    1. Remove the retaining clips.
      • Disconnect the LH and RH washer hoses.
  1. Position the windshield wiper mounting arm and pivot shaft (17566) assembly aside.
    1. Remove the nuts.
    1. Remove the bolt.
    1. Position the windshield wiper mounting arm and pivot shaft assembly aside.
  1. Remove the windshield wiper mounting arm and pivot shaft assembly.
    1. Disconnect the electrical connector.
    1. Remove the windshield wiper mounting arm and pivot shaft assembly.
----------------------------------------------------------------------------------------
Motor —Windshield Wiper Removal
  1. Remove the windshield wiper mounting arm and pivot shaft (17566) assembly; refer to Mounting Arm and Pivot Shaft .
  1. Remove the windshield wiper motor (17508).
    1. Remove the output shaft bolt.
    1. Remove the bolts.
    1. Remove the windshield wiper motor.

May 01, 2009 | 1999 Lincoln Town Car

2 Answers

Front Windsheild Wipers


I have 2007 only. please rate as solved if this is what you needed. good luck.

SECTION 501-16: Wipers and Washers 2007 Freestar/Monterey Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 04/27/2006
Wiper Motor — Windshield s7w~us~en~file=adobe.gif~gen~ref.gif Printable View (104 KB) Removal
  1. Remove the windshield wiper arms.
  1. NOTE: Disconnect the washer hose before removing the cowl panel grille.
    Remove the pushpin-type retainers and the cowl panel grille.
  1. Remove the washer hose grommet from the cowl panel and position aside the washer hose.
  1. If equipped, remove the A/C air inlet filter.
  1. Remove the 9 cowl panel bolts and position aside the cowl panel.
  1. Disconnect the windshield wiper motor electrical connector.
  1. Remove the cowl panel from the vehicle.
  1. Remove the 4 bolts and the windshield wiper motor.
    s7w~us~en~file=n0001518.gif~gen~ref.gif
Installation
  1. Position the wiper pivot arms on the windshield wiper motor and install the bolt.
    • Tighten to 15 Nm (11 lb-ft).
  1. Install the 3 windshield wiper-to-cowl panel bolts.
    • Tighten to 15 Nm (11 lb-ft).
  1. Position the cowl panel in the vehicle and connect the windshield wiper motor electrical connector.
  1. Install the washer hose and grommet in the cowl panel.
  1. Install the 9 cowl panel bolts.
    • Tighten to 6 Nm (53 lb-in).
  1. If equipped, install the A/C air inlet filter.
  1. Position the cowl panel grille in the vehicle and connect the washer hose.
  1. Install the pushpins.
  1. Install the windshield arms and nuts.
    • Tighten to 27 Nm (20 lb-ft).
  1. Cycle and park the windshield wipers to check for correct alignment.
3c6f4d5.gif
b8a2ebf.gif

Apr 09, 2009 | 2006 Ford Freestar

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

266 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

chargerhp
chargerhp

Level 3 Expert

813 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...