Question about 2001 Oldsmobile Silhouette

1 Answer

Missfire #3 3.4 olds 01 - 2001 Oldsmobile Silhouette

Posted by on

Ad

1 Answer

What is the question?

The #3 cylinder- as well as all cylinders have
to be tested for the cause

Posted on Dec 12, 2012

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

01 Audi A6 p0351 p0352 and p0353


Look at fuel trim on a professional scanner

You still have the same codes for the same cylinder
misfires,IF the codes are correct

The misfires could come from valve issues,the valves themselves
or the variable cam actuators if that applies,or from fuel issues,but
not as likely on all three cyl on same bank

You need to do a cylinder leak down test on all cylinders--to eliminate mechanical issues

Then a cylinder contribution test electrically with scope software

Then scope the timing events,the cam advance events,the crank
position, all layered on the same screen & see if they line
up where they belong.

If the cams are not the issue, then your left with a serious vacuum
leak in the intake on one bank.

What I'm saying, is you have one bank with misfires apparently
not now from the ignition since the coils were replaced

Mar 19, 2014 | 2001 Audi A6

1 Answer

I got a 2001 Oldsmobile aurora that the code reads PO301


well that code means ur have a missfire in cylinder one change the wires for the spark plugs that really the only thing i can think off beacuse you have already done the spark plugs and the oxygen sensors and the coil packs

Feb 26, 2013 | 2001 Oldsmobile Aurora

1 Answer

1999 malibu 3.1 clyd 5 missfire and now random missfire oil light is on lfters very noise runs rough


Have you confirmed there is no oil pressure and the oil level is full on the dipstick?

The oil pump is turned by the oil pump drive located under the throttle body. The oil pump drive is run of from the cam shaft. It is not uncommon for the camshafts to break on these engines.

It may not be a bad idea to pull the front valve cover and turn the engine over by hand to see if all the rockers are moving.

Jan 17, 2012 | Cars & Trucks

1 Answer

Hard to start cly 3 missfire smoothens out fast


You might want to pressure test the cooling system and remove the #3 spark plug. After the pressure tester sits on there for a few hours look into the combustion chamber to see if there is coolant. Misfires like these can sometimes be the result of a leaky head gasket. Also white smoke in the exhaust can be a sign. I assume the spark plug looks good?

Dec 23, 2011 | Volvo S40 Cars & Trucks

1 Answer

I have a 01 dodge ram 1500 with a check engine code of p0308 can you tell me what it is and how to repair it


it means number 8 cylinder missfire.start off with the good old fashion tune up,plugs,wires, throttle body cleaning air filter. if recently done remove plugs and inspect for damage or wrong gap.

Jun 09, 2010 | 2001 Dodge Ram 1500 Truck 2WD

2 Answers

Check engine light flashing runs rough not firing on all cylinder2000 lincoln navigator with large triton engine Hooked up diagnnostic and it said 1. system too lean bank #2 2. Unable to bleed up fuel tank...


you may try your rotor button and distributor cap. and spark plug wires. try your map sensor also they tend to cause a lot of misfiring if they go bad.hope this helps.

Apr 20, 2010 | Lincoln Navigator Cars & Trucks

1 Answer

Missfire on cylinder 2 and can't open bonnet - Fiat Bravo '01


There are other, professional ways to get the bonnet open without having to break anything. Have someone push down on the hood a bit while someone else pulls on the release. If that doesnt work, you can get behind the grill and access the release by going under grill, find hood latch and pull release.
The misfire can be a number of things. Check for spark,Install a spark tester between spark plug and wire. If there is no spark, check wire, module, coil. If there is spark, check plug, Perform a compression check.

Jul 23, 2009 | Fiat Strada Cars & Trucks

2 Answers

Missfire on number 3 coil on 2001 S type Jaguar 3.0 V6 Sport


Check the igniter module.
I assume you have a ecu code telling you #3 coil is missfiring ?
If so also check the crankshaft angle sensor .
If it is not an error code do a compression test and check the injector.
Hope this helps
Regards
George

Jul 08, 2009 | 2001 Jaguar S-Type

1 Answer

1998 honda civic cel code 71-74


code 71 means #1 cylinder missfire 72 Means #2 cylinder missfire 73 means #3 cylinder missfire and 74 means #4 cylinder Missfire

May 29, 2009 | 1998 Honda Civic

Not finding what you are looking for?
2001 Oldsmobile Silhouette Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...