Question about Kia Sedona

Open Question

Tension rod bar bushing - Sedona Kia Cars & Trucks

Posted by Anonymous on

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 2 Answers

SOURCE: 2003 Dodge Durango clunking noise in front end can

With the information given this is not a sure solution. Questions that need to be asked is when does this happen, turning at slow speedm high speed, when hitting a pot hole etc? Since you have replaced a lot of things already, assuming you have NEW good quality parts so you did not replace bad parts with new bad parts i would definitelu check the pitman arm. This runs from the stering gear to the tierod. It can give you some good clunks while steering, especially at low speed when there is a lot of resistance. Check it by having someone turning the steering wheel when watchin/feeling it.

Posted on Sep 18, 2009

Ad
  • 5 Answers

SOURCE: what is the bar or rod called that is on the

The rods that connect the K-member (subframe) to the lower control arms are called "strut rods". Your local auto parts store should carry the bushings.

Posted on Dec 10, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace front anti roll bar bushes


Frank, you haven't said what make or model your car is.
However, have a look on the following link - it will take you to Youtube:
how to replace anti roll bar bushes Google Search

It's not a particularly difficult job. It entails loosening the drop-links/tie bars that connect to the torsion bar - the anti roll bar, then loosening the bolts holding the anti roll bar in place.

Just be aware that the anti roll bar is in effect a 'spring' and is under tension. Loosen the retaining bolts gradually, slowly.

replacing the bushes is straight forward. Once you have removed the anti roll bar just lever the old rubber bushes out with a screwdriver and push the new ones into place .. then reassemble everything.

In the most general of terms you would do the job in a couple of hours

May 12, 2016 | Cars & Trucks

2 Answers

Car shekes when hit bumps


Check for bad wheel balance, struts, lower ball joints ( no upper joints) , outer tie rod ends, inner tie rod ends, stabilizer bar bushings, lower control arm bushings , and finally a wheel alignment ,you have some bad looseness in one or more of these front end parts. GOOD LUCK FRIEND.

Mar 15, 2015 | 2001 Dodge Intrepid

1 Answer

How to change shaft stabalizer bar on 2002 buick rendezvous


The stabilizer bard rarely need replaced. There 2 brackets holding the bar in place. They both have a bushing that goes bad from time to time. The real issue with the stabilizer bar is the end- the stabilizer rods on the ends. You can usually replace these in about 1/2 hour and the job is done. Go to your local parts store and order the stabilizer rod and bushing kit, The kit will come with an in instruction sheet, and it is a very simple job.

Dec 31, 2014 | 2002 Buick Rendezvous

1 Answer

My 96 Camaro has the rear swaying a little extra over speed bumps and turns with bumps. Changed front/rear sway bar bushings and gonna do tie-rods soon.. Any hints...


check the rear track bar bushings this runs from side of axle up to body. also the lower link bushings in rear. have you checked air pressure ?

Dec 23, 2010 | 1996 Chevrolet Camaro

1 Answer

How do you replace the tie rod end bushing on a


If your having a hard time taking the nut off the tie rod without the stud spinning use a jack or pry bar and put some pressure on the bottom of the tie rod. An impact gun will usually zip it right off too. Be sure to get an alignment once you replace the tie rod.

Jun 13, 2010 | 2000 Hyundai Elantra

1 Answer

Rattling/clattering from suspension on poor roads


check shock absorber mounting support/ must be worn-out/ or stabilizer bar rubber bush / or stabilizer linkage rubber bush/ check tie rod ends balljoints / check lower suspension arms balljoints as well as upper suspension arm balljoints and lastly check strut bar rubber bushes/ all the mentioned parts can be easily seen underneath the car....

Apr 09, 2010 | 2003 Land Rover Range Rover

2 Answers

What is the bar or rod called that is on the drivers side hooked to the lower controll arm and goes towards the front it has bushings in it were it connects to the lower controll arm- thoes bushings are...


The rods that connect the K-member (subframe) to the lower control arms are called "strut rods". Your local auto parts store should carry the bushings.

Dec 02, 2009 | 1997 Ford Thunderbird LX

1 Answer

How to replace tie rods and bushings in a 1997 dodge caravan


I recommend you get a Haynes or Chilton repair manual for most auto parts stores ($20-$30). But to save you some money:
Tie Rods:
1. Loosen the lug nuts.
2. Raise front of vehicle.
3, Support it with jack stands.
4. Chock/Block the rear tires.
5. Set the parking brake.
6. Remove the front tire.
7. Mark the nut shaped end of the tie rod and the jam nut with a straight line on top.
8. Using two wrenches - one on the tie rod (nut shaped) end and the other on the jam nut,..loosen SLIGHTLY the jam nut (clockwise turn). While loosening the jam nut - make sure you count the number of turns 1/4, 1/2, 1, 2 etc...
9. Using 11/32 Socket remove the tie-rod end to steering knuckle nut.
10. Use a tie rod end separator (fork) or ball joint separator (jaws) and separate the tie rod from the steering knuckle.
11. Before turning the tire rod off the steering arm: Count the number of turns coming off the arm using the mark you put on the tie rod nut shaped end.
Notice on the final turn off the arm what the mark position is. This wil be the position you start when screwing the new tie rod on.
12. Place the jam nut back just short of it's original position.
13. Screw the new tie rod back starting with that start position and with the same number of turns.
14. Connect the tie rod and steering knuckle.
15. Tighten the tie rod to steering knuckle nut to 40 ft-lbs.
16. The tie rod end and jam nut should then be tightened. They should be close anyway within a 1/8 turn.
17. Install lug nuts.
18. Lower Van.
19. Tighten lug nuts to 100 ft-lbs. Using the everyother nut until all are tightened process.
20. Wheel alignment? Test drive Van and have checked at an alignment shop.

The Stabilizer Bar Bushings:
Steps 1. thru Step 6 above. Remove both tires.
7. Remove bolts (should be 10 of them) attaching the cradle plate to the bottom of the front suspension cradle.
8. Remove the cradle plate.
9. Remove the stablizer bar links from the stabilzer bar. Confused? There is a straight bar coming from the Strut down to the sway (stabilizer) bar (which goes from one side of the Van to the other). Remove this nut.
10. Remove the stabilizer (sway) bar bushing retainers (one on each side) from the front suspension cradle.
11. Be careful this bar is heavy and will fall suddenly and may hit you on the head!!
12. Remove the bar and bushings as a unit (together).
13. Install the new bushings with the slits facing the rear of the Van and the square corners facing the ground.
14. Make sure you clean the areas on the bar where the bushings are positioned.
15. Use lubricant (non-petroleum based, like vegetable oil) to easy re-assembly.
16. Re-assembly is pretty much the reverse.
Hints:
a. Align the stabilizer bar in position using the depressions in the cradle.
b. Do not tighten all-the-way the bushing retainers until later.
c. Tighten stabilizer bar to link stabilzer (sway) bar to 65 ft-lbs.
d. Tighten bushing retainer nuts to 50 ft-lbs.
e. Tighten the cradle plate bolts:
M14 at 123 ft-lbs
M12 at 80 ft-lbs.

Let mne know if this worked for you. Good Luck!!
Any other questions? Drop me a line on fixya.com!


Nov 21, 2009 | 2000 Dodge Caravan

2 Answers

Noise in sway bar area/94 camry 4 cyl


Possible tranny or engine mount. Check bushings. Check brake pad backing plates (loose), check brake pad movement (add shims), but most likely mounts. you need to torque the engine while an assistant checks for bad mounts.

Aug 31, 2009 | 1994 Toyota Camry

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

35 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kia Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

yadayada
yadayada

Level 3 Expert

76649 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8522 Answers

Are you a Kia Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...