No warning buzzer that my lights are on

Jody, this is out of the manual
Warning light Comes on or blinks when: Comes on There is a malfunction in the 4-wheel drive system Blinks slowly The difference in wheel rotation is large
Have checked by a good technician, press the helpful button

http://www.vadennissanservicecontracts.com/owners-manual/nissan/2013-Nissan-Titan.pdf

Buzzer is dead. As long as the lights don't stay on, keep driving. Buzzers are annoying anyway.

Cocking time ? Cocking what ?

Not surprisingly, many others have experienced problems with the ignition switch on this car. Historically, it is not a sound, but that the key is stuck in the ignition. http://repairpal.com/key-will-not-come-out-of-ignition-570 Your problem sounds different, but it may be related. Although I do not recommend the fix in the link above, it is possible the previous owner of your car did perform this fix and it has resulted in the problem you now have. My better guess is that the chime/buzzer has failed due to moisture or dirt and is no longer producing the sound that it should, but instead is altered to the ringing you describe.To disable follow these instructions:

1. Turn the ignition switch to the RUN (or ON) position. (DO NOT
START THE ENGINE)
2. Wait until the safety belt warning light turns off. (Approximately 1
minute)
Step 3 must be completed within 50 seconds after the safety belt
warning light turns off.
3. For the seating position being disabled, at a moderate speed, buckle
then unbuckle the safety belt 9 times, ending in the unbuckled state.
(Step 3 must be completed within 50 seconds after the safety belt
warning light turns off.)
After Step 3, the safety belt warning light will be turned on for three
seconds.
4. Within 10 seconds of the light turning on, at a moderate speed, buckle
then unbuckle the safety belt.
This will disable the BeltMinder feature for that seating position if it
is currently enabled. As confirmation, the safety belt warning light will
flash 4 times per second for 3 seconds.
This will enable the BeltMinder feature for that seating position if it
is currently disabled. As confirmation, the safety belt warning light will
flash 4 times per second for 3 seconds, followed by 3 seconds with the
light off, then followed by the safety belt warning light flashing 4 times
per second for 3 seconds again.
I hope this helps. Good luck.

There is a procedure in the owners manual on page 110.

BeltMinder activation and deactivation procedure
1. Turn the ignition switch to the RUN (or ON) position. (DO NOT START THE ENGINE.)
2. Wait until the safety belt warning light turns off. (Approximately 1–2 minutes.)
• Steps 3–5 must be completed within 60 seconds or the procedure will have to be repeated.
3. Buckle then unbuckle the safety belt three times, ending with the safety belt unbuckled. This can be done before or during BeltMinder warning activation.
4. Turn on the parklamps/headlamps, turn off the parklamps/headlamps.
5. Buckle then unbuckle the safety belt three times, ending with the safety belt unbuckled
• After step 5 the safety belt warning light will be turned on for three seconds.
6. Within seven seconds of the safety belt warning light turning off, buckle then unbuckle the safety belt.
• This will disable BeltMinder if it is currently enabled, or enable BeltMinder if it is currently disabled.
7. Confirmation of disabling BeltMinder is provided by the safety belt warning light flashing four times per second for three seconds.
8. Confirmation of enabling BeltMinder is provided by:
• The safety belt warning light flashing four times per second for three seconds.
• Followed by three seconds with the safety belt warning light off.
• Once again, the safety belt warning light will flash four times per second for three seconds.
9. After receiving confirmation, the deactivation/activation procedure is complete.

If you did not get an owners manual with your truck ( purchased used ), you can download one from Ford :
https://www.fleet.ford.com/maintenance/owners_manuals/default.asp

the little PASEO BUZZER may have failed or is not getting power to it
Cheers Rob.

hi,light switch is located at the left side lower area of cluster,if you remove your key then a warning buzzer on,you left one light on,if your battery is flat,maybe some electrical consumer is draining your battery,if you see the sign of battery in your cluster even you remove the key,your alt.is defect,ty

Have you checked that the headlight switch is in the right position? Are the headlights or parking lights still on when the key is removed?

If so, then rotate the lamp switch to the correct position and the buzzer will go off. Headlights and parking lights are not controlled through the key circuits.

To stop the service interval warning and sound coming on please follow the following steps.
1. insert key into ignition. 2. using right hand press and hold the odometer reset stalk. 3 using your left hand turn on the ignition ( dont start the Car) 4 now use your left hand to press the clock adjust stalk and turnit to the left. ( just advance the time by 1 minute) 5 release both stalks and then turn ignition off , then on again and your service warnig light and sound will now not appear for the next 5000 miles. ( repeat the above when it comes on again) This will also save you £30.00 for the garage to do it.

HELLO MATE

IVE GOT THE MANUAL AND THAT LIGHT IS YA COOLANT LEVEL IS LOW TOP UP WITH COOLANT RUN FOR 5 MINS SWITCH OFF WAIT A COUPLE MINS THEN START AGAIN

STEVE