Question about 1995 Mitsubishi 3000GT

Open Question

How do I install a keyless entry system on a 1997 Mistubishi 3000GT

I have a ICD model 2RTA2 keyless entry system ready to install

Posted by on

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
mcdevito75
  • 1970 Answers

SOURCE: replace harmonic balancer 1996 mitsubishi 3000gt

mcdevito75 here, You"ll need speciall tools for this job, let your local shop do the job.

Posted on Jun 17, 2010

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I can't find the alarm fuse on my 1997 Blazer


Didn't come with an alarm. Only Keyless Entry System. If you have an alarm, it was installed by someone after manufacture.

Dec 28, 2012 | 1997 Chevrolet Blazer

1 Answer

Replace harmonic balancer 1996 mitsubishi 3000gt


mcdevito75 here, You"ll need speciall tools for this job, let your local shop do the job.

Jun 16, 2010 | 1996 Mitsubishi 3000GT

1 Answer

How do i reprogram electronic door locks


Programming Electronic Door Lock Control System NOTE: The electronic door lock control processor (14B001) erases all previous keyless entry remote transmitter (15K601) from memory when the keyless entry remote transmitters are programmed or reprogrammed. The electronic door lock control processor can store up to four keyless entry remote transmitters in memory.


  • To program (or reprogram) keyless entry remote transmitter into the electronic door lock control processor, perform the following steps:
  1. Turn ignition switch to the RUN position and momentarily short the two terminals of the program connector taped to the wire assembly and located behind the glove compartment. All doors should lock and then unlock. Remove shorting pin.
  1. Press any button on keyless entry remote transmitter. All doors should lock and then unlock to verify the keyless entry remote transmitter has been programmed. If door locks do not respond, press button again (up to three times maximum with the same keyless entry remote transmitter).
  1. Repeat the above step to program additional keyless entry remote transmitters into the electronic door lock control processor (up to four keyless entry remote transmitters maximum).
  1. Turn ignition switch OFF. All doors should lock and then unlock.
  1. Check operation.

Jun 05, 2010 | 1997 Ford Windstar

1 Answer

HI, CAN I BUY A KEYLESS ENTRY SYSTEM ON EBAY, FOR MY BUICK CENTURY 97?, I MEAN DOES MY CAR HAS THE OPTION FOR THAT SYSTEM (KEYLESS). THANKS.


Generic answer... If you have electic locks, installing a Keyless should be fairly easy, if you do not, it gets much more complicated.

Peace,

Mar 28, 2010 | 1997 Buick Century

1 Answer

Diagnose keyless entry system of 1997 Cherokee


Before replacing any Relay. Try disconnecting the negative side of the battery for at least 2-minutes to de-energize the security system, re-setting itself. The reconnect the battery and try your security (and options) system again.
The only other big question that you will have to know: is this a factory installed security system or an aftermarket security system? This makes a difference in security systems, relays etc.

Dec 27, 2009 | 1997 Jeep Cherokee Country

2 Answers

Volume on honda civic radio not working


atxhonda is right. Your going to have to replace the stereo and an aft mkt stereo will be the cheapest by far, however you should know that 96-00 Civics keyless entry control unit is inside the factory unit and by replacing it with an aftermarket deck you will lose you factory keyless entry system. If you don't have or use honda factory keyless entry or maybe you have an aft mkt keyless entry installed than I would go with the aft mkt deck.

Dec 06, 2009 | 1997 Honda Civic

1 Answer

2000 Lincoln Towncar. Keypad on door will not unlock doors. Interior lights do come on. The last two keys pushed simultaneously will occasionally lock the doors. I am using the code printed on a sticker in...


The driver door module (DDM) is connected on the standard corporate protocol (SCP) communication network. The DDM controls many functions including power windows, power door locks and remote keyless entry. The DDM also communicates with the driver seat module (DSM) to control the power mirror and seat memory functions.
Do you know anything about automotive electronic control modules ?
The driver door module (DDM) receives inputs from the digital transmission range (DTR) sensor, ignition switch, seat switch, window/door lock switches, lighting control module (LCM), keyless entry keypad switch and remote transmitter. The DDM outputs consists of keyless entry keypad switch illumination, power door lock actuators, luggage compartment release solenoid, horn relay, and lighting control module (LCM).
Best thing to do would be to have a factory scan tool hooked up to check for DTC'S diagnostic trouble codes . That should be the first step if it's not programming the code.
  • The doors do not lock/unlock using the keyless entry keypad
  • Keypad.
  • Circuitry.
  • Driver door module (DDM).
  • GO to Pinpoint Test L .

PINPOINT TEST L: THE DOORS DO NOT LOCK/UNLOCK USING THE KEYLESS ENTRY KEYPAD CONDITIONS DETAILS/RESULTS/ACTIONS L1 RETRIEVE THE RECORDED RESULTS FROM BOTH CONTINUOUS AND ON DEMAND SELF TESTS Use the recorded DDM DTCs from the Continuous and On Demand self tests.
  • Are any DTCs recorded?
Yes For DTC B1525, GO to L3 .

For all other DDM DTCs, REFER to the DDM Diagnostic Trouble Code (DTC) Index.

No If the door locks are inoperative, GO to L2 .

If the keypad illumination does not operate, GO to L10 .

If the keypad illumination is on continuously, GO to L14 .
L2 CHECK THE DOOR LOCK OPERATION Check the door lock operation by depressing a door lock switch.
  • Do the door locks operate?
Yes GO to L3 .

No GO to Pinpoint Test E . L3 MONITOR THE DDM PID KEY_PAD
Scan tool
Monitor the DDM PID KEY_PAD.
  • Are any of the keyless entry keypad switch numbers present?
Yes GO to L4 .

No GO to L5 . L4 CHECK THE KEYLESS ENTRY KEYPAD SWITCH
Keyless Entry Keypad Switch C525
Monitor the DDM PID KEY_PAD.
  • Are any of the keyless entry keypad switch numbers present?
Yes If 1/2, REPAIR Circuit 78 (LB/YE). TEST the system for normal operation.
If 3/4, REPAIR Circuit 79 (LG/RD). TEST the system for normal operation.
If 5/6, REPAIR Circuit 121 (YE/BK). TEST the system for normal operation.
If 7/8, REPAIR Circuit 122 (YE). TEST the system for normal operation.
If 9/0, REPAIR Circuit 123 (RD). TEST the system for normal operation.

No INSTALL a new keyless entry keypad switch; for additional information, REFER to Keypad-Keyless Entry . L5 CHECK THE KEYLESS ENTRY KEYPAD INPUT WITH THE KEYLESS ENTRY KEYPAD SWITCH Monitor the DDM PID KEY_PAD, while depressing all the keyless entry keypad switches one at a time.
  • Are all the keyless entry keypad switches operating correctly?
Yes GO to L9 .

No GO to L6 . L6 CHECK CIRCUIT 797 (LG/VT) FOR VOLTAGE
Keyless Entry Keypad C525
Measure the voltage between keyless entry keypad C525-7, Circuit 797 (LG/VT), and ground; and between keyless entry keypad C525-8, Circuit 797 (LG/VT), and ground.
  • Are the voltages greater than 10 volts?
Yes GO to L7 .

No REPAIR Circuit 797 (LG/VT). TEST the system for normal operation. L7 CHECK THE KEYLESS ENTRY KEYPAD SWITCH INPUT While monitoring the DDM PID KEY_PAD, momentarily connect a fused (7.5A) jumper wire between positive battery post and keyless entry keypad switch C525 as follows:
    Keypad Button Keyless Keypad Switch C525 Circuit 1/2 Pin 3 78 (LB/YE) 3/4 Pin 4 79 (LG/RD) 5/6 Pin 5 121 (YE/BK) 7/8 Pin 6 122 (YE) 9/0 Pin 1 123 (RD)

  • Are all the keyless entry keypad switch inputs operating correctly?
Yes INSTALL a new keyless entry keypad switch; for additional information, REFER to Keypad-Keyless Entry .

No GO to L8 . L8 CHECK THE KEYLESS ENTRY KEYPAD SWITCH CIRCUITRY FOR AN OPEN
DDM
Measure the resistance between keyless entry keypad switch C525 and DDM as follows:
    Keyless Keypad Switch C525 DDM Circuit Pin 3 C521 Pin 8 78 (LB/YE) Pin 4 C521 Pin 13 79 (LG/RD) Pin 5 C521 Pin 16 121 (YE/BK) Pin 6 C520 Pin 24 122 (YE) Pin 1 C520 Pin 25 123 (RD)

  • Is the resistance less than 5 ohms?
Yes INSTALL a new DDM; for additional information, REFER to Section 419-10 . TEST the system for normal operation.

No REPAIR the circuit in question. TEST the system for normal operation. L9 CHECK THE KEYLESS ENTRY KEYPAD BACKLIGHT Depress a key on the keyless entry keypad.
  • Does the keypad illumination operate correctly?
Yes INSTALL a new DDM. For additional information, REFER to Section 419-10 . TEST the system for normal operation.

No If the keypad illumination does not operate, GO to L10 .

If the keypad illumination is on continuously, GO to L14 . L10 CHECK THE KEYPAD - DDM ACTIVE COMMAND KEYPAD BACKLIGHTING LIGHT ON AND OFF Trigger the DDM active command KEYPAD BACKLIGHTING LIGHT ON and OFF.
  • Does the keypad illumination turn off and on?
Yes INSTALL a new DDM. For additional information, REFER to Section 419-10 . TEST the system for normal operation.

No GO to L11 . L11 CHECK DDM GROUND - JUMPER CIRCUIT 66 (LB) TO GROUND
DDM 522
Connect a fused (7.5A) jumper wire between DDM C522-4, circuit 66 (LB), and ground.
  • Does the keypad illuminate?
Yes INSTALL a new DDM; for additional information, REFER to Section 419-10 . TEST the system for normal operation.

No GO to L12 . L12 CHECK CIRCUIT 51 (BK/W) FOR OPEN
Keyless Entry Keypad C525
Measure the voltage between keyless entry keypad C525-7, circuit 797 (LG/VT), and ground; and between keyless entry keypad C525-8, circuit 797 (LG/VT), and ground.
  • Are the voltages greater than 10 volts?
Yes GO to L13 .

No REPAIR circuit 797 (LG/VT). TEST the system for normal operation. L13 CHECK CIRCUIT 66 (LB) FOR OPEN Measure the resistance between keyless entry keypad C525-2, Circuit 66 (LB), and DDM C522-4, Circuit 66, (LB).
  • Is the resistance less than 5 ohms?
Yes INSTALL a new keyless entry keypad switch; for additional information, REFER to Keypad-Keyless Entry .

No REPAIR Circuit 66 (LB). TEST the system for normal operation. L14 CHECK THE KEYPAD ILLUMINATION - DDM DISCONNECTED
DDM C522

  • Does the keypad illumination turn off?
Yes INSTALL a new DDM; for additional information, REFER to Section 419-10 . TEST the system for normal operation.

No GO to L15 . L15 CHECK KEYLESS ENTRY KEYPAD FOR SHORT TO GROUND
Keyless Entry Keypad C525

  • Does the keypad illumination turn off?
Yes GO to L16 .

No INSTALL a new keyless entry keypad switch. For additional information, REFER to Keypad-Keyless Entry . TEST the system for normal operation. L16 CHECK CIRCUIT 66 (LB) FOR SHORT TO GROUND Measure resistance between DDM C522-4, circuit 66 (LB), and ground.
  • Is resistance greater than 10,000 ohms?
Yes System OK. CLARIFY the concern with the customer.

No REPAIR circuit 66 (LB). TEST the system for normal operation.

Nov 03, 2017 | Lincoln Town Car Cars & Trucks

1 Answer

Intall Remote Keyless Entry System in an 02 Honda Accord


You got the Wrong Information! Go to Wal Mart and Purchase a "Bulldog Security Keyless Entry" System for your Car. It will cost you a Quarter of the Price and is Just asw Reliable as the Factory Unit! Got one on My Truck with Remote Start also and it works GREAT! Should cost about $50.00 Bucks or so.

Jan 22, 2009 | 2002 Honda Accord

1 Answer

How to install a keyless entry system!


buy a system from a parts store and follow the directions

Oct 12, 2008 | 1997 Mazda Protege

2 Answers

Keyless entry module


Under the hood fuse panel, my 1997 doesn't have keyless entry so it might be aftermarket.

Aug 07, 2008 | 1997 Mazda MX-6

Not finding what you are looking for?
1995 Mitsubishi 3000GT Logo

Related Topics:

60 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

77169 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8729 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...