Question about Cars & Trucks

Open Question

Proton Arena just starts and dies, replaced crank sensor already , no error codes

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: 2008 nissan maxima crank sensor

mas air meter could cause this problem.

Posted on Jul 30, 2008

Ad
autodr
  • 260 Answers

SOURCE: 1998 dodge caravan crank shaft or cam shaft sensor??

maybe have autozone or equal scan the computer for codes. could be a misfire in the cyl. somewhere. give me a code number and i will try to assist you further.

Posted on Nov 09, 2008

ams51pr
  • 21 Answers

SOURCE: 2000 Mitsubishi Galant Dying at Random

It seems like a ground problem. First check all fuses to see that they have a good contact. Second, verify the battery terminals for good contact. Third verify the charging condition in the alternator battery system., remember shoul be around 14volts with car running.

Posted on Jan 15, 2009

cmm19987
  • 82 Answers

SOURCE: 1996 Chevy Suburban C1500 V8 5.7 suddenly died

Is the fuel pump coming on?

Posted on Nov 10, 2009

krolik7
  • 1 Answer

SOURCE: 2004 Kia Optima no start after timing belt, crank, cam sensor replacement

did you use aftermarket crank sensor? if so that might be your problem. dealer has several different ones, by providing vin number, but there is only one after market for all optimas 01-05. try to connect thick pink wire and thick orange wire together on the ignition failure sensor. you might have the same problem as me. good luck.

Posted on Jan 15, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2007 1,5 Proton Arena. Cold starting very rough (stalls). Once on temp all Ok. ps yellow engine light on whole time.


You need to have the diagnostic codes read. Anything else is pure guessing. Those codes can point you in the right direction and often will tell you exactly what is wrong.

Aug 19, 2016 | Proton Cars & Trucks

1 Answer

Car wont start ,no spark after replacing crank sensor


what maker of vehicle and motor are we talking about

EDIT Proton Arena 15i

something else is wrong
what ever is causing the no start does not have a code

yes PO335 right code and right part to replace6f1d8180-d547-4234-91c5-2b7b4c4df33f.jpg

car-wont-start-no-spark-after-replacing-r5w3vwqiamwa5yzrroebjr3v-2-2.jpg

Jun 22, 2016 | Cars & Trucks

1 Answer

1994 Jeep Cherokee country starts fine after driving awhile it will not start back doesnt die but cranks and cranks setting a code 54 already replaced camshaft sensor Also spitting and sputtering while...


could it be that the catalytic converter is clogged? The pressure will release over time, but eventually will build up back pressure as it runs stalling the engine.... then taking up to an hour for the pressure to release enough to start again.

Apr 27, 2014 | Cars & Trucks

1 Answer

2003 dodge Dakota 4.7l. High mileage. OBDII throwing a new code everytime I fix something. Crank sensor & Cam sensor - replaced. IAC-replaced. PCM-replaced. Throttle body cleaned. O2...


Have you checked the wiring that goes to both the Crank and Cam sensors? Most of the time the wires are close to a heat source (ie: exhaust manifold) and the plastic covering starts to melt causing the cooper on wires to make contact and thus making engine stop, you will have to take off the protective covering as well as tape around the wires and inspect each and every one. Had same problem with Dodge caravan, it turns out the Crank Sensor plug wires were melted together. Good Luck.

Oct 26, 2013 | 1993 Dodge Dakota

2 Answers

98 blazer 4.3 engine won't start code p0336, already replaced crank sensor


which crank sensor do you replaced ? the P0336 means P0336 Crankshaft Position Sensor A Circuit Range/Performance.

________________
autel maxidas 708

Feb 25, 2013 | 1998 Chevrolet Blazer

1 Answer

P1115 and P1116 Error Codes


P1115 Engine Coolant Temperature (ECT) Sensor Circuit Intermittent High Voltage/IAT - B Circuit High Input
P1116 Engine Coolant sensor out of range/ECT Sensor Out Of Self Test Range
--------
Renault+Nissan key prog 2 in 1

Nov 29, 2012 | 2000 Mercury Sable

1 Answer

Any ideas for error codes? p0171,p0174,p01775,po1777 and p01350


Vacuum leak????Did you google the error codes?
PO171 is a lean code. get in there when it's running and listen.
You may have to stick a small rubber hose in your ear and hunt around a bit to find the HISSING noise.Check the EGR!!!
Check the resistance in the coolant temp sensor,also. It tells the ECM how much fuel is needed. if it's out of spec....

Nov 14, 2012 | 1999 Oldsmobile Aurora

1 Answer

Have a 1997 ford explorer with 4.0 sohc that died at stop and would not start. cranked but no start. error code was p0340. replaced crank sensor and started but died again in less than 2 minutes. still...


p0340 states: Cam Position Sensor A circuit (Bank 1, or single sensor)

p1318 : unknown code cannot find online or in my code reader definitions.

remember the code does not mean the part is bad just where to look for bad wires, connectors and to test for bad parts.

Sep 16, 2012 | Ford Explorer Cars & Trucks

1 Answer

1996 buick skylark


1996 buick skylark i see this problem all the time, it starts and then shuts off let it cool down and it starts back up only to die again.lol... been there to many time, replce the crank sensor and you sould be fine. the crank sensor is behind the crank pully, jack the car up and pull the passanger side wheel the crank pully will be right there, you may have to rent a pully puller from a part store but the job is simple

Mar 22, 2012 | Buick Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

42 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...