I have scanned for codes it stored a po171 a p0174 a po302...p0171 is bank 1 lean p0174 is bank 2 lean p0302 is cyl #2 misfire i cleared codes replaced plugs cked wires.test drove it reset the same codes after 3 drive cycles.i noticed that the miss happens all the time between1300 rpm-1600 rpm..it has no miss before or after that rpm range... i think there may be tsb on this issue..any help apprichiated doyal.
An expert who has achieved level 2 by getting 100 points
An expert that got 10 achievements.
An expert that got 5 achievements.
An expert whose answer got voted for 100 times.
Re: 1999windstar missing prob
Check the pcv valve vacum lines for a leak a vacum leak will set 171 174 codes. lift the hood with engine running and listen for a air leak , check all vacum lines if no vacum leaks can be found then clean the mass air flow sensor by spraying carb cleaner directly on it for about 5 seconds. in other words take the air filter cover up and spray down the tube that leads to engine. shine a light down hose first and see if u can see the mass air flow sensor so u can get a direct hit
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US. click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need. Goodluck!
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
DTC code PO400 could be caused by a clogged EGR valve or EGR tube. try cleaning the EGR valve, tube
DTC code PO171 is fuel system too lean bank 1
DTC code PO174 is fuel system too lean Bank 2
Most likely suspects are O2 sensors, But can be caused by vacuum leaks and also can be Mass airflow sensor (MAF) try cleaning with electrical parts cleaner
DTC code PO 302 is a misfire at cylinder # 2
Check spark plugs and wires
Try cleaning the EGR Valve first along with changing the spark plug first, and see if any codes erase, in other words start with the cheaper fixes first, as some problems can be causing the other other codes
code p0128 indicates a mechanical fault ( could be the thermostat stuck open)
code p0174 -system too lean -bank2 ===causes --intake /exhaust leak--fuel pressure/pump--injectors--AIR system--hose connection/s
code po171 refers to system too lean bank 1 same as po174 with the HO2S sensor being the culprit. As to all being related . only by way of the o2 sensors
code p0442 is not connected to the first 3 as it is in a different section of the fuel system
P0171------ system too lean bank#1
Po174------ system too lean bank#2
For these 2 codes, try cleaning the maf sensor (mass air flow), that is mounted in the big black hose that goes from the air filter housing to the throttle plate, if it is dirty, that will cause those 02 sensors to send a signal to the computor to lean the air fuel mixture. If cleaning it doesn't work, the sensors will probably need changing.
P0300---- Random/multiple cylinder misfire
P0316---- Cylinder misfire at start up---- first 100 revolutions.
On those 2 codes, you have to do some testing to find out why there is a misfire.
weak coil pack
fowling spark plugs/wires
Low fuel pressure
P0171 is system too lean bank 1, P0174 is too lean bank 2, and 302 is misfire bank 1. Look for vacuum leaks. If you don't find them, put a vacuum gage on it can check. The P0171 is almost always a vacuum leak. If not other possibilities are front O2 sensor is too old and should be replaced (if mileage is greater than 100k then replace). Try injector cleaner. Misfires are usually bad spark plugs, but could possibly be caused by insufficient fuel. I've never had a car of mine in bad enough shape to have that error.